23136EMD1 bearing: complete specifications & equivalents
The 23136EMD1 is a ISO 15 radial bearing sized 180 x 300 x 96 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 180 mm |
| Outer diameter D | 300 mm |
| Width B | 96 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | brass, machined (M1) |
| Basic dynamic load rating C | 1490 kN |
| Basic static load rating C0 | 1960 kN |
| Fatigue load limit Pu | 88.7 kN |
| Limiting speed (mechanical) | 1300 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 27400 g |
| Manufacturer designation | NTN 23136EMD1 |
| Standard | ISO 15 |
| Catalog version | NTN Ball and Roller Bearings CAT.No.2203E |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203E) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203E); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 23100-series range
| Bore d | 7.087 in |
|---|---|
| Outer diameter D | 11.811 in |
| Width B | 3.78 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 60 mm |
| Smallest bore in 23100-series | 100 mm |
| Largest outer diameter in 23100-series | 1420 mm |
| Width range across 23100-series | 52–412 mm |
| Bore position in 23100-series (smallest first) | 9 of 36 |
| Bore above smallest 23100-series size | 80 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 23136EMKD1 | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same NTN 23100-series envelope, cage and ratings; this is the cylindrical-bore execution of the tapered-bore 23136EMKD1 (K/K30 sleeve or tapered-seat mounting). Verify shaft arrangement. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 23136EMD1 model number is decoded
For heavy radial load with misalignment on a 180 mm shaft, NTN supplies 23136EMD1: sphered outer raceway, two roller rows, one-piece machined brass cage (EM high-capacity design), oil speed 1,700 r/min. On the NTN nameplate the suffix cluster after the size reads in order: cage design (EM), bore (cylindrical), lubrication feature (D1); 23136EMD1 is assembled exactly in that order. Pu 88.7 kN is the catalogue fatigue load limit for 23136EMD1, used in the adjusted-life equation at contaminated or partial-film conditions typical of mining and vibrating duty. The 60.0 mm section height hosts the spherical roller geometry; shaft and housing fillet radii must clear the chamfer table so the 96 mm-wide ring seats fully on both sides. Fit the cylindrical-bore 23136EMD1 with the inner ring heated (max 120 °C) for the shaft interference; the outer ring slides into the housing with its spherical seat able to pivot after seating.
Typical equipment & failure modes
Common applications
- offshore and marine propulsion shaftlines
- large wind-turbine main-shaft arrangements
- steel-mill and heavy crusher main shafts
- mining shovel and dragline swing shafts
Known failure patterns
- lubricant starvation at the centre rib area when the D1/W33 groove is not connected to a relubrication supply
- machined EM cage wear from inadequate oil film at the cage-guiding surfaces
- micro-pitting when the EHL film is thinner than the raceway composite roughness
- hard-particle indentation through the open arrangement in dusty mining duty
- brinelling from static overload or a hammer blow during sleeve mounting
Selection pitfalls — read before you substitute
- At 180 mm bore 23136EMD1 is normally mounted on adapter/withdrawal sleeves with hydraulic assistance; follow the NTN drive-up angle or oil-injection procedure — manual nut tightening cannot set the multi-tonne seating correctly.
- Never substitute 23136EMD1 by envelope alone: the 1960 kN C0 and 88.7 kN Pu are specific to the NTN EM machined-brass-cage execution, and vibrating duty depends heavily on cage identity.
- The two roller rows must share load equally — a tilted spacer or unequal abutment on the 96 mm-wide ring loads one row only and shows as asymmetric race polish during inspection.
- Do not confuse EA and EM at the same number: 23136EMD1 carries EM machined-brass-cage; swapping to the other cage execution changes mass, speed behaviour and sometimes suitability for vibration, even though the 180×300 mm envelope is identical.
- The D1/W33 groove only helps if the housing has a matching grease passage; mounting a D1 23136EMD1 in a solid block with no port wastes the feature and leaves the centre rows under-lubricated.
- The 1490/1960 kN ratings, 88.7 kN Pu and 27400 g mass are NTN Ball and Roller Bearings CAT.No.2203E values for 23136EMD1 (EM machined-brass-cage/D1); another maker's same-envelope part revises internal geometry, so re-verify ratings and cage before substitution on vibrating or rated drives.
Frequently asked questions
What are the dimensions and catalogue data of 23136EMD1?
23136EMD1 is an NTN double-row spherical roller bearing to ISO 15: 180 mm bore, 300 mm OD and 96 mm width (7.087 × 11.811 × 3.78 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 1490 kN, C0 1960 kN, Pu 88.7 kN, grease limiting speed 1,300 r/min, oil 1,700 r/min, mass about 27400 g. It is open, with one-piece machined brass cage (EM high-capacity design).
What is the difference between the K/K30 tapered bore and the cylindrical bore versions?
23136EMD1 has a cylindrical bore and mounts directly on a machined shaft seat. Its tapered-bore counterpart is 23136EMKD1 (K = 1:12, or K30 = 1:30 on the wide series), intended for adapter/withdrawal-sleeve mounting.
What do EA and EM mean on NTN spherical roller bearings?
EA is the NTN standard-capacity/high-capacity execution with a pressed sheet-steel window cage; EM is the high-capacity execution with a one-piece machined brass cage. Both use the optimised symmetric-roller design, but cage identity changes mass, speed behaviour and suitability for duties like vibrating screens, so they are separate order numbers. 23136EMD1 is the EM machined-brass-cage execution, listed with the ＊ ULTAGE new-generation mark.
What do D1 and W33 mean on 23136EMD1?
D1 is NTN's outer-ring lubrication feature: an annular groove with oil holes around the outer ring, aligned with a housing grease port so lubricant reaches both roller rows directly. 23136EMD1 carries D1; W33 is the equivalent industry-spelled annular-groove-and-holes feature seen on other executions.
How much misalignment and axial load can 23136EMD1 take?
The sphered outer raceway compensates static and dynamic misalignment in the order of 1–2° (verify the exact 2203E figure for the 23100 series); beyond that, load concentrates on one roller row. Load is predominantly radial with a moderate axial share in either direction — 1490 kN C / 1960 kN C0 — but sustained pure axial load is not recommended because it unloads one row.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN Ball and Roller Bearings CAT.No.2203E on 2026-10-01. Read our editorial & correction policy.