23160 bearing: complete specifications & equivalents
The 23160 is a ISO 15 radial bearing sized 300 x 500 x 160 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 300 mm |
| Outer diameter D | 500 mm |
| Width B | 160 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 3368 kN |
| Basic static load rating C0 | 5100 kN |
| Fatigue load limit Pu | 380 kN |
| Reference speed (thermal) | 950 rpm |
| Limiting speed (mechanical) | 1200 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 125000 g |
| Manufacturer designation | SKF 23160 CC/W33 |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 9.1 spherical roller bearings |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 9.1 spherical roller bearings) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 9.1 spherical roller bearings); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 23100-series range
| Bore d | 11.811 in |
|---|---|
| Outer diameter D | 19.685 in |
| Width B | 6.299 in |
| ISO bore code | 60 |
| Radial section height (D−d)/2 | 100 mm |
| Smallest bore in 23100-series | 100 mm |
| Largest outer diameter in 23100-series | 790 mm |
| Width range across 23100-series | 52–248 mm |
| Bore position in 23100-series (smallest first) | 16 of 25 |
| Bore above smallest 23100-series size | 200 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 23160 | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; D/B cross-verified against Schaeffler HR1 2022; brand-specific OEM equivalents (NSK/FAG/NTN) pending multi-source data. |
| 23160-CCK-W33 | SKF | full Dimensions and internal design equivalent — standard interchange. | Tapered-bore (1:12) execution on OH3160 adapter sleeve; same ISO 15 envelope, separate order number. |
| C3160 | SKF | full Dimensions and internal design equivalent — standard interchange. | SKF CARB toroidal bearing C 3160 shares the 300×500×160 mm envelope with ratings within 10 %; it self-aligns but floats axially and cannot locate the shaft — locating/non-locating pair, not a substitute. |
| C3160-K | SKF | full Dimensions and internal design equivalent — standard interchange. | SKF CARB toroidal bearing C 3160 K shares the 300×500×160 mm envelope with ratings within 10 %; it self-aligns but floats axially and cannot locate the shaft — locating/non-locating pair, not a substitute. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 23160 model number is decoded
In SKF catalogue PUB BU/P1 17000, 23160 appears as 23160 CC/W33: an open, double-row spherical roller bearing, self-aligning by virtue of the sphered outer raceway, sized 300×500×160 mm to the ISO 15 boundary plan. Digit by digit, 23160 reads as bearing type 2 (spherical roller, two barrel-roller rows), dimension series 31, and bore reference 60 resolving to 300 mm; 500 mm OD and 160 mm width are the matching ISO 15 boundary values. In SKF suffix language, E marks the optimized high-capacity design and CC/W33 the pressed-steel-cage execution with relubrication groove; both are open bearings — the sealed variant carries the 2CS5 suffix and the vibrating-screen execution VA405. The 100.0 mm radial section height ((500−300)/2) and 125000 g catalogue mass frame a 300 mm bore bearing rated at 3368 kN C — roughly 11.23 kN of dynamic capacity per millimetre of bore before application factors. Drive-on force must go through the ring being fitted: press or induction-heat the inner ring onto the 300 mm shaft (max 120 °C) and never transmit mounting force through the roller complement, or the raceways brinell.
Typical equipment & failure modes
Common applications
- wind-turbine main shaft support
- heavy rolling-mill work-roll chocks
- large dredger and marine winch drums
- steel-plant continuous-caster segments
Known failure patterns
- raceway fatigue spalling of the sphered outer raceway after extended service above the catalogue L10 rating
- inner-ring raceway spalling from edge loading when misalignment exceeds the self-aligning recovery range
- stamped-steel cage fatigue after long service in high-vibration screening duty without the VA405 execution
- surface distress and smearing when the relubrication interval is exceeded — the W33 groove is only effective if grease actually reaches the roller rows
- electrical pitting on VFD-driven shafts without grounding protection
Selection pitfalls — read before you substitute
- At 300 mm bore the ring mass makes cocking during mounting a real risk; guide the bearing square, confirm seat contact around the full circumference, and re-check the self-aligning swing after the housing cap is torqued down.
- The 23100-series series at 300 mm bore (500×160 mm) is the medium-OD wide envelope for heavy continuous duty; it is wider than a 222 bearing in the same OD class, so housing width and spacer stack must be re-checked before substitution.
- Never use the tapered-bore EK/K variant's drive-up figures on this cylindrical-bore 23160; clearance reduction targets differ, and over-driving a cylindrical bore onto an oversized journal cracks the inner ring.
- Open spherical roller bearings rely on the housing seals; in screening or crusher duty a failed seal lets grit into the sphered raceway and the 23160 pits long before its L10 life.
- The 3368/5100 kN ratings are SKF catalogue values for this exact execution (23160 CC/W33); SKF can revise internal geometry without changing the order number, so keep the catalogue version (SKF catalogue PUB BU/P1 17000) with the specification and re-verify for critical drives.
- SKF lists several executions of 23160 (cylindrical bore as listed, tapered-bore 23160 CCK/W33 variant, plus sealed and vibrating-screen options in the same envelope); they are not interchangeable order numbers — quote the full 23160 CC/W33 designation when purchasing.
Frequently asked questions
What are the dimensions and catalogue data of 23160?
The 23160 CC/W33 is a double-row spherical roller bearing with 300 mm bore, 500 mm outer diameter and 160 mm width (11.811 × 19.685 × 6.299 in) per ISO 15. From SKF catalogue PUB BU/P1 17000: basic dynamic load rating C 3368 kN, C0 5100 kN, fatigue load limit Pu 380 kN, reference speed 950 r/min, limiting speed 1,200 r/min, mass about 125000 g. It is an open, self-aligning bearing with two pressed-steel cages with a floating guide ring.
How does the 23160 bore code work?
The last two digits of 23160 are bore code 60, so 60 × 5 = 300 mm bore. The 500 mm OD and 160 mm width come from the ISO 15 dimension-series plan (dimension series 31 (medium OD, wide)), shared with other spherical roller bearings of the same code.
What does the CC/W33 suffix mean on 23160?
CC denotes two pressed-steel cages with a floating guide ring between the roller rows, and W33 adds an annular groove plus three lubrication holes in the outer ring for relubrication. CCK/W33 is the 1:12 tapered-bore counterpart.
Can 23160 accommodate misalignment and axial load?
Yes on both counts. The sphered outer raceway lets the bearing self-align ≈ 0.5–2.5° depending on series, absorbing shaft deflection and housing-seat errors. The two barrel-roller rows also carry bidirectional axial load in addition to heavy radial load — this is the key difference from cylindrical roller bearings, which take no axial load.
When should the tapered-bore 23160K variant be used instead?
Choose the K (1:12 tapered bore) variant when the bearing must seat on an adapter or withdrawal sleeve — typical for long shafts, frequent dismounting, or stepped shafts where machining a precision journal is impractical. Sleeve mounting requires measuring clearance reduction or axial drive-up, not nut torque. The cylindrical-bore 23160 listed here seats directly on a machined journal.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 9.1 spherical roller bearings on 2026-09-26. Read our editorial & correction policy.