23188B bearing: complete specifications & equivalents
The 23188B is a ISO 15 radial bearing sized 440 x 720 x 226 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 440 mm |
| Outer diameter D | 720 mm |
| Width B | 226 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel |
| Basic dynamic load rating C | 5800 kN |
| Basic static load rating C0 | 10100 kN |
| Fatigue load limit Pu | 685 kN |
| Limiting speed (mechanical) | 390 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 370000 g |
| Manufacturer designation | NTN 23188B |
| Standard | ISO 15 |
| Catalog version | NTN Ball and Roller Bearings CAT.No.2203E |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203E) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203E); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 23100-series range
| Bore d | 17.323 in |
|---|---|
| Outer diameter D | 28.346 in |
| Width B | 8.898 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 140 mm |
| Smallest bore in 23100-series | 100 mm |
| Largest outer diameter in 23100-series | 1420 mm |
| Width range across 23100-series | 52–412 mm |
| Bore position in 23100-series (smallest first) | 23 of 36 |
| Bore above smallest 23100-series size | 340 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 23188BK | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same NTN 23100-series envelope, cage and ratings; this is the cylindrical-bore execution of the tapered-bore 23188BK (K/K30 sleeve or tapered-seat mounting). Verify shaft arrangement. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 23188B model number is decoded
23188B is an NTN double-row spherical roller bearing: two rows of symmetric rollers on a sphered outer raceway, 440×720×226 mm to ISO 15, with pressed-steel cage (standard execution). On the NTN nameplate the suffix cluster after the size reads in order: cage design (—), bore (cylindrical), lubrication feature (none); 23188B is assembled exactly in that order. At 5800 kN C and 370000 g mass the 23100 series part is built for shock and vibration; the 226 mm-wide ring needs square abutments to keep both rows equally loaded. Catalogue mass 370000 g (370.00 kg) for the 440×720×226 mm execution includes the basic cage and both roller rows; shaft and housing shoulders must support that ring squarely. Never mount 23188B by striking the outer ring through the roller set; drive through ring faces (or the adapter sleeve nut) and support the ring square to avoid brinelling the 720 mm race.
Typical equipment & failure modes
Common applications
- heavy vibrating screens and grizzly feeders
- offshore and marine propulsion shaftlines
- large wind-turbine main-shaft arrangements
- steel-mill and heavy crusher main shafts
Known failure patterns
- raceway spalling at the roller ends when misalignment or deflection concentrates the line contact
- cage damage when a mounting force is applied through the roller set instead of the ring face
- sliding wear and heat when relubrication intervals ignore the groove (D1/W33) supply path
- false brinelling on stopped machines exposed to screen or crusher vibration
- fretting corrosion between adapter sleeve and tapered bore when the drive-up is insufficient
Selection pitfalls — read before you substitute
- At 440 mm bore 23188B is normally mounted on adapter/withdrawal sleeves with hydraulic assistance; follow the NTN drive-up angle or oil-injection procedure — manual nut tightening cannot set the multi-tonne seating correctly.
- Oil relubrication toward 500 r/min needs drain and level design; flooding the 226 mm cavity churns heat through the heavy roller set and cage despite the higher oil speed figure.
- Adapter-sleeve mounting requires the correct sleeve series and locknut for the 440 mm shaft; a sleeve sized to bore alone ignores thread, width and the oil-injection option on large K30 seats.
- The D1/W33 groove only helps if the housing has a matching grease passage; mounting a grooved 23188B in a solid block with no port wastes the feature and leaves the centre rows under-lubricated.
- Open spherical rollers swallow dust in mining duty; specify labyrinth or taconite seals externally, or the 390 r/min grease rating is lost to abrasive wear long before fatigue.
- The 5800/10100 kN ratings, 685 kN Pu and 370000 g mass are NTN Ball and Roller Bearings CAT.No.2203E values for 23188B (basic); another maker's same-envelope part revises internal geometry, so re-verify ratings and cage before substitution on vibrating or rated drives.
Frequently asked questions
What are the dimensions and catalogue data of 23188B?
23188B is an NTN double-row spherical roller bearing to ISO 15: 440 mm bore, 720 mm OD and 226 mm width (17.323 × 28.346 × 8.898 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 5800 kN, C0 10100 kN, Pu 685 kN, grease limiting speed 390 r/min, oil 500 r/min, mass about 370000 g. It is open, with pressed-steel cage (standard execution).
What is the difference between the K/K30 tapered bore and the cylindrical bore versions?
23188B has a cylindrical bore and mounts directly on a machined shaft seat. Its tapered-bore counterpart is 23188BK (K = 1:12, or K30 = 1:30 on the wide series), intended for adapter/withdrawal-sleeve mounting.
What do EA and EM mean on NTN spherical roller bearings?
EA is the NTN standard-capacity/high-capacity execution with a pressed sheet-steel window cage; EM is the high-capacity execution with a one-piece machined brass cage. Both use the optimised symmetric-roller design, but cage identity changes mass, speed behaviour and suitability for duties like vibrating screens, so they are separate order numbers. 23188B is the basic execution.
What do D1 and W33 mean on 23188B?
23188B is listed without a D1/W33 outer-ring groove in 2203E; lubrication is supplied from the ring sides. D1 (NTN spelling) and W33 add the annular groove plus holes and are ordered as distinct suffixed executions of the same envelope.
How much misalignment and axial load can 23188B take?
The sphered outer raceway compensates static and dynamic misalignment in the order of 1–2° (verify the exact 2203E figure for the 23100 series); beyond that, load concentrates on one roller row. Load is predominantly radial with a moderate axial share in either direction — 5800 kN C / 10100 kN C0 — but sustained pure axial load is not recommended because it unloads one row.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN Ball and Roller Bearings CAT.No.2203E on 2026-10-01. Read our editorial & correction policy.