23292 bearing: complete specifications & equivalents
The 23292 is a ISO 15 radial bearing sized 460 x 830 x 296 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 460 mm |
| Outer diameter D | 830 mm |
| Width B | 296 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | brass, machined (M1) |
| Basic dynamic load rating C | 8958 kN |
| Basic static load rating C0 | 13700 kN |
| Fatigue load limit Pu | 880 kN |
| Reference speed (thermal) | 400 rpm |
| Limiting speed (mechanical) | 560 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 695000 g |
| Manufacturer designation | SKF 23292 CA/W33 |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 9.1 spherical roller bearings |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 9.1 spherical roller bearings) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 9.1 spherical roller bearings); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 23200-series range
| Bore d | 18.11 in |
|---|---|
| Outer diameter D | 32.677 in |
| Width B | 11.654 in |
| ISO bore code | 92 |
| Radial section height (D−d)/2 | 185 mm |
| Smallest bore in 23200-series | 90 mm |
| Largest outer diameter in 23200-series | 870 mm |
| Width range across 23200-series | 52.4–310 mm |
| Bore position in 23200-series (smallest first) | 25 of 26 |
| Bore above smallest 23200-series size | 370 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 23292 | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; D/B cross-verified against Schaeffler HR1 2022; brand-specific OEM equivalents (NSK/FAG/NTN) pending multi-source data. |
| 23292-CAK-W33 | SKF | full Dimensions and internal design equivalent — standard interchange. | Tapered-bore (1:12) execution on AOHX3292 withdrawal sleeve; same ISO 15 envelope, separate order number. |
| C3292-MB | SKF | full Dimensions and internal design equivalent — standard interchange. | SKF CARB toroidal bearing C 3292 MB shares the 460×830×296 mm envelope with ratings within 10 %; it self-aligns but floats axially and cannot locate the shaft — locating/non-locating pair, not a substitute. |
| C3292-KMB | SKF | full Dimensions and internal design equivalent — standard interchange. | SKF CARB toroidal bearing C 3292 KMB shares the 460×830×296 mm envelope with ratings within 10 %; it self-aligns but floats axially and cannot locate the shaft — locating/non-locating pair, not a substitute. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 23292 model number is decoded
The 23292 CA/W33 is a 460×830×296 mm spherical roller bearing — the dimension series 32 (medium OD, extra wide) entry for a 460 mm shaft, with two rows of symmetrical barrel rollers for combined radial and axial load. Digit by digit, 23292 reads as bearing type 2 (spherical roller, two barrel-roller rows), dimension series 32, and bore reference 92 resolving to 460 mm; 830 mm OD and 296 mm width are the matching ISO 15 boundary values. In SKF suffix language, CA/W33 means the brass-cage CA execution — often preferred for the largest bores and for shock/vibration duty where a rigid machined cage matters; W33 adds the relubrication groove. The sealed 2CS5 and vibrating-screen VA405 are separate executions. Selection arithmetic: the C0/C ratio is about 1.53 (static 13700 kN against dynamic 8958 kN), typical of a spherical roller sized for heavy combined loads, and the 880 kN fatigue load limit Pu is the equivalent-load floor used in the life calculation. Spherical roller bearings are routinely specified with C3 clearance because the tight inner-ring fit and inner/outer temperature gradient eat into the CN running clearance — check the residual clearance after mounting with feeler gauges.
Typical equipment & failure modes
Common applications
- SAG and ball-mill drive shafts
- large mining crusher main shafts
- wind-turbine main shaft support
- heavy rolling-mill work-roll chocks
Known failure patterns
- raceway fatigue spalling of the sphered outer raceway after extended service above the catalogue L10 rating
- inner-ring raceway spalling from edge loading when misalignment exceeds the self-aligning recovery range
- cage pocket wear or fracture from roller skew at insufficient minimum load or rapid acceleration
- surface distress and smearing when the relubrication interval is exceeded — the W33 groove is only effective if grease actually reaches the roller rows
- seal-lip wear and grease purge loss when an open bearing is run without functioning housing seals
Selection pitfalls — read before you substitute
- At 460 mm bore the ring mass makes cocking during mounting a real risk; guide the bearing square, confirm seat contact around the full circumference, and re-check the self-aligning swing after the housing cap is torqued down.
- The 23200-series series at 460 mm bore (830×296 mm) adds still more width for shock-loaded and vibratory loads; it does not interchange with a 231 bearing of the same bore because the 296 mm width changes abutment spacing, even though the 830 mm OD matches.
- The 695000 g mass and 296 mm width mean abutment faces must be square to the axis within the bearing's own P0 tolerance; a tilted spacer tilts the outer ring and concentrates load on one roller row of 23292.
- Catalogue reference speed and limiting speed are different limits: the 400 r/min reference is a thermal criterion under load, while the 560 r/min limiting value is the mechanical ceiling — observe both.
- The 8958/13700 kN ratings are SKF catalogue values for this exact execution (23292 CA/W33); SKF can revise internal geometry without changing the order number, so keep the catalogue version (SKF catalogue PUB BU/P1 17000) with the specification and re-verify for critical drives.
- SKF lists several executions of 23292 (cylindrical bore as listed, tapered-bore 23292 CCK/W33 variant, plus sealed and vibrating-screen options in the same envelope); they are not interchangeable order numbers — quote the full 23292 CA/W33 designation when purchasing.
Frequently asked questions
What are the dimensions and catalogue data of 23292?
The 23292 CA/W33 is a double-row spherical roller bearing with 460 mm bore, 830 mm outer diameter and 296 mm width (18.11 × 32.677 × 11.654 in) per ISO 15. From SKF catalogue PUB BU/P1 17000: basic dynamic load rating C 8958 kN, C0 13700 kN, fatigue load limit Pu 880 kN, reference speed 400 r/min, limiting speed 560 r/min, mass about 695000 g. It is an open, self-aligning bearing with a one-piece machined brass cage guided on the inner ring (CA design).
How does the 23292 bore code work?
The last two digits of 23292 are bore code 92, so 92 × 5 = 460 mm bore. The 830 mm OD and 296 mm width come from the ISO 15 dimension-series plan (dimension series 32 (medium OD, extra wide)), shared with other spherical roller bearings of the same code.
What does the CA/W33 suffix mean on 23292?
CC denotes two pressed-steel cages with a floating guide ring between the roller rows, and W33 adds an annular groove plus three lubrication holes in the outer ring for relubrication. CCK/W33 is the 1:12 tapered-bore counterpart.
Can 23292 accommodate misalignment and axial load?
Yes on both counts. The sphered outer raceway lets the bearing self-align ≈ 0.5–2.5° depending on series, absorbing shaft deflection and housing-seat errors. The two barrel-roller rows also carry bidirectional axial load in addition to heavy radial load — this is the key difference from cylindrical roller bearings, which take no axial load.
When should the tapered-bore 23292K variant be used instead?
Choose the K (1:12 tapered bore) variant when the bearing must seat on an adapter or withdrawal sleeve — typical for long shafts, frequent dismounting, or stepped shafts where machining a precision journal is impractical. Sleeve mounting requires measuring clearance reduction or axial drive-up, not nut torque. The cylindrical-bore 23292 listed here seats directly on a machined journal.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 9.1 spherical roller bearings on 2026-09-26. Read our editorial & correction policy.