23992-NTN bearing: complete specifications & equivalents
The 23992-NTN is a ISO 15 radial bearing sized 460 x 620 x 118 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 460 mm |
| Outer diameter D | 620 mm |
| Width B | 118 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel |
| Basic dynamic load rating C | 2340 kN |
| Basic static load rating C0 | 4950 kN |
| Fatigue load limit Pu | 325 kN |
| Limiting speed (mechanical) | 480 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 107000 g |
| Manufacturer designation | NTN 23992 |
| Standard | ISO 15 |
| Catalog version | NTN Ball and Roller Bearings CAT.No.2203E |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203E) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203E); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 23900-series range
| Bore d | 18.11 in |
|---|---|
| Outer diameter D | 24.409 in |
| Width B | 4.646 in |
| ISO bore code | 92 |
| Radial section height (D−d)/2 | 80 mm |
| Smallest bore in 23900-series | 160 mm |
| Largest outer diameter in 23900-series | 1820 mm |
| Width range across 23900-series | 45–315 mm |
| Bore position in 23900-series (smallest first) | 18 of 38 |
| Bore above smallest 23900-series size | 300 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 23992K | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same NTN 23900-series envelope, cage and ratings; this is the cylindrical-bore execution of the tapered-bore 23992K (K/K30 sleeve or tapered-seat mounting). Verify shaft arrangement. |
| 23992 | SKF | full Dimensions and internal design equivalent — standard interchange. | Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier. |
| 23992-CAK-W33 | SKF | full Dimensions and internal design equivalent — standard interchange. | Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 23992-NTN model number is decoded
23992 is the basic execution of NTN's spherical roller range for a 460 mm shaft — 2340 kN basic dynamic capacity in a 107000 g, open ISO 15 envelope. The leading digits are the ISO 15 dimension series (23900 series); the bore code resolves to 460 mm (two-digit code ×5, with the 00–03 exception table), and 620 mm OD / 118 mm width follow the general plan. The 80.0 mm radial section over the 460 mm bore carries two roller rows; capacity per millimetre of bore is about 5.1 kN/mm, among the highest of rolling bearings for the ISO 15 envelope. Selection: the C0/C ratio of 2.12 (4950/2340 kN) reflects the heavy static and shock proportioning of 23992; size the equivalent load at the required L10 with shock factor for the application. Never mount 23992 by striking the outer ring through the roller set; drive through ring faces (or the adapter sleeve nut) and support the ring square to avoid brinelling the 620 mm race.
Typical equipment & failure modes
Common applications
- cement-rotary-kiln support and trunnion rolls
- large SAG/ball-mill trunnion and pinion shafts
- heavy vibrating screens and grizzly feeders
- offshore and marine propulsion shaftlines
Known failure patterns
- lubricant starvation at the centre rib area when the D1/W33 groove is not connected to a relubrication supply
- cage damage when a mounting force is applied through the roller set instead of the ring face
- sliding wear and heat when relubrication intervals ignore the groove (D1/W33) supply path
- fretting corrosion between adapter sleeve and tapered bore when the drive-up is insufficient
- asymmetric wear on the two roller rows from sustained angular misalignment beyond the self-aligning range
Selection pitfalls — read before you substitute
- At 460 mm bore 23992 is normally mounted on adapter/withdrawal sleeves with hydraulic assistance; follow the NTN drive-up angle or oil-injection procedure — manual nut tightening cannot set the multi-tonne seating correctly.
- The cylindrical-bore 23992 and its tapered-bore counterpart 23992K share envelope and ratings but not mounting: do not order the K variant unless the drawing specifies a sleeve or tapered seat.
- Adapter-sleeve mounting requires the correct sleeve series and locknut for the 460 mm shaft; a sleeve sized to bore alone ignores thread, width and the oil-injection option on large K30 seats.
- K and K30 are different tapers — K is 1:12 and K30 is 1:30 on the wide series; an adapter sleeve for one will not mount the other 460 mm bearing, and drive-up procedures differ.
- The cylindrical-bore 23992 and its tapered-bore counterpart 23992K share envelope and ratings but not mounting: do not order the K variant unless the drawing specifies a sleeve or tapered seat.
- The 2340/4950 kN ratings, 325 kN Pu and 107000 g mass are NTN Ball and Roller Bearings CAT.No.2203E values for 23992 (basic); another maker's same-envelope part revises internal geometry, so re-verify ratings and cage before substitution on vibrating or rated drives.
Frequently asked questions
What are the dimensions and catalogue data of 23992?
23992 is an NTN double-row spherical roller bearing to ISO 15: 460 mm bore, 620 mm OD and 118 mm width (18.11 × 24.409 × 4.646 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 2340 kN, C0 4950 kN, Pu 325 kN, grease limiting speed 480 r/min, oil 620 r/min, mass about 107000 g. It is open, with pressed-steel cage (standard execution).
What is the difference between the K/K30 tapered bore and the cylindrical bore versions?
23992 has a cylindrical bore and mounts directly on a machined shaft seat. Its tapered-bore counterpart is 23992K (K = 1:12, or K30 = 1:30 on the wide series), intended for adapter/withdrawal-sleeve mounting.
What do EA and EM mean on NTN spherical roller bearings?
EA is the NTN standard-capacity/high-capacity execution with a pressed sheet-steel window cage; EM is the high-capacity execution with a one-piece machined brass cage. Both use the optimised symmetric-roller design, but cage identity changes mass, speed behaviour and suitability for duties like vibrating screens, so they are separate order numbers. 23992 is the basic execution.
What do D1 and W33 mean on 23992?
23992 is listed without a D1/W33 outer-ring groove in 2203E; lubrication is supplied from the ring sides. D1 (NTN spelling) and W33 add the annular groove plus holes and are ordered as distinct suffixed executions of the same envelope.
How much misalignment and axial load can 23992 take?
The sphered outer raceway compensates static and dynamic misalignment in the order of 1–2° (verify the exact 2203E figure for the 23900 series); beyond that, load concentrates on one roller row. Load is predominantly radial with a moderate axial share in either direction — 2340 kN C / 4950 kN C0 — but sustained pure axial load is not recommended because it unloads one row.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN Ball and Roller Bearings CAT.No.2203E on 2026-10-01. Read our editorial & correction policy.