24026EMD1 bearing: complete specifications & equivalents
The 24026EMD1 is a ISO 15 radial bearing sized 130 x 200 x 69 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 130 mm |
| Outer diameter D | 200 mm |
| Width B | 69 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | brass, machined (M1) |
| Basic dynamic load rating C | 682 kN |
| Basic static load rating C0 | 936 kN |
| Fatigue load limit Pu | 42.2 kN |
| Limiting speed (mechanical) | 1900 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 7820 g |
| Manufacturer designation | NTN 24026EMD1 |
| Standard | ISO 15 |
| Catalog version | NTN Ball and Roller Bearings CAT.No.2203E |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203E) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203E); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 24000-series range
| Bore d | 5.118 in |
|---|---|
| Outer diameter D | 7.874 in |
| Width B | 2.717 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 35 mm |
| Smallest bore in 24000-series | 65 mm |
| Largest outer diameter in 24000-series | 1580 mm |
| Width range across 24000-series | 35–462 mm |
| Bore position in 24000-series (smallest first) | 6 of 42 |
| Bore above smallest 24000-series size | 65 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 24026EMK30D1 | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same NTN 24000-series envelope, cage and ratings; this is the cylindrical-bore execution of the tapered-bore 24026EMK30D1 (K/K30 sleeve or tapered-seat mounting). Verify shaft arrangement. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 24026EMD1 model number is decoded
24026EMD1 is an NTN double-row spherical roller bearing: two rows of symmetric rollers on a sphered outer raceway, 130×200×69 mm to ISO 15, with one-piece machined brass cage (EM high-capacity design). The leading digits are the ISO 15 dimension series (24000 series); the bore code resolves to 130 mm (two-digit code ×5, with the 00–03 exception table), and 200 mm OD / 69 mm width follow the general plan. The sphered outer raceway lets the inner-ring assembly pivot, accommodating shaft deflection and housing misalignment (around 1–2° for this class; use the 2203E value for the exact series) without edge loading the rollers. 130 mm bore is 5.118 in and 200 mm OD is 7.874 in; the ISO 15 envelope swaps between brands, but the 682/936 kN ratings and cage design are NTN 2203E values. On vibrating-duty shafts verify the radial clearance class and cage choice at order time; the open 24026EMD1 leaves sealing and the C3/C4 clearance decision to the application drawing.
Typical equipment & failure modes
Common applications
- cement-rotary-kiln support and trunnion rolls
- large SAG/ball-mill trunnion and pinion shafts
- heavy vibrating screens and grizzly feeders
- offshore and marine propulsion shaftlines
Known failure patterns
- lubricant starvation at the centre rib area when the D1/W33 groove is not connected to a relubrication supply
- machined EM cage wear from inadequate oil film at the cage-guiding surfaces
- sliding wear and heat when relubrication intervals ignore the groove (D1/W33) supply path
- fretting corrosion between adapter sleeve and tapered bore when the drive-up is insufficient
- rolling-contact fatigue after the catalogue L10 life at the actual load
Selection pitfalls — read before you substitute
- At 130 mm bore 24026EMD1 is normally mounted on adapter/withdrawal sleeves with hydraulic assistance; follow the NTN drive-up angle or oil-injection procedure — manual nut tightening cannot set the multi-tonne seating correctly.
- Oil relubrication toward 2,400 r/min needs drain and level design; flooding the 69 mm cavity churns heat through the heavy roller set and cage despite the higher oil speed figure.
- Self-aligning does not mean unlimited misalignment: beyond the catalogue angle the outer ring's spherical travel is exhausted and the 682 kN rating no longer applies.
- Open spherical rollers swallow dust in mining duty; specify labyrinth or taconite seals externally, or the 1,900 r/min grease rating is lost to abrasive wear long before fatigue.
- Minimum load must be maintained even at rest under vibration: an unloaded 24026EMD1 on a stopped screen false-brinells; parking brakes and shaker isolation both matter.
- The 682/936 kN ratings, 42.2 kN Pu and 7820 g mass are NTN Ball and Roller Bearings CAT.No.2203E values for 24026EMD1 (EM machined-brass-cage/D1); another maker's same-envelope part revises internal geometry, so re-verify ratings and cage before substitution on vibrating or rated drives.
Frequently asked questions
What are the dimensions and catalogue data of 24026EMD1?
24026EMD1 is an NTN double-row spherical roller bearing to ISO 15: 130 mm bore, 200 mm OD and 69 mm width (5.118 × 7.874 × 2.717 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 682 kN, C0 936 kN, Pu 42.2 kN, grease limiting speed 1,900 r/min, oil 2,400 r/min, mass about 7820 g. It is open, with one-piece machined brass cage (EM high-capacity design).
What is the difference between the K/K30 tapered bore and the cylindrical bore versions?
24026EMD1 has a cylindrical bore and mounts directly on a machined shaft seat. Its tapered-bore counterpart is 24026EMK30D1 (K = 1:12, or K30 = 1:30 on the wide series), intended for adapter/withdrawal-sleeve mounting.
What do EA and EM mean on NTN spherical roller bearings?
EA is the NTN standard-capacity/high-capacity execution with a pressed sheet-steel window cage; EM is the high-capacity execution with a one-piece machined brass cage. Both use the optimised symmetric-roller design, but cage identity changes mass, speed behaviour and suitability for duties like vibrating screens, so they are separate order numbers. 24026EMD1 is the EM machined-brass-cage execution, listed with the ＊ ULTAGE new-generation mark.
What do D1 and W33 mean on 24026EMD1?
D1 is NTN's outer-ring lubrication feature: an annular groove with oil holes around the outer ring, aligned with a housing grease port so lubricant reaches both roller rows directly. 24026EMD1 carries D1; W33 is the equivalent industry-spelled annular-groove-and-holes feature seen on other executions.
How much misalignment and axial load can 24026EMD1 take?
The sphered outer raceway compensates static and dynamic misalignment in the order of 1–2° (verify the exact 2203E figure for the 24000 series); beyond that, load concentrates on one roller row. Load is predominantly radial with a moderate axial share in either direction — 682 kN C / 936 kN C0 — but sustained pure axial load is not recommended because it unloads one row.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN Ball and Roller Bearings CAT.No.2203E on 2026-10-01. Read our editorial & correction policy.