24036 bearing: complete specifications & equivalents
The 24036 is a ISO 15 radial bearing sized 180 x 280 x 100 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 180 mm |
| Outer diameter D | 280 mm |
| Width B | 100 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 1134 kN |
| Basic static load rating C0 | 1730 kN |
| Fatigue load limit Pu | 156 kN |
| Reference speed (thermal) | 1500 rpm |
| Limiting speed (mechanical) | 2200 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 23000 g |
| Manufacturer designation | SKF 24036 CC/W33 |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 9.1 spherical roller bearings |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 9.1 spherical roller bearings) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 9.1 spherical roller bearings); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 24000-series range
| Bore d | 7.087 in |
|---|---|
| Outer diameter D | 11.024 in |
| Width B | 3.937 in |
| ISO bore code | 36 |
| Radial section height (D−d)/2 | 50 mm |
| Smallest bore in 24000-series | 65 mm |
| Largest outer diameter in 24000-series | 700 mm |
| Width range across 24000-series | 35–218 mm |
| Bore position in 24000-series (smallest first) | 11 of 27 |
| Bore above smallest 24000-series size | 115 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 24036 | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; D/B cross-verified against Schaeffler HR1 2022; brand-specific OEM equivalents (NSK/FAG/NTN) pending multi-source data. |
| 24036-CCK30-W33 | SKF | full Dimensions and internal design equivalent — standard interchange. | Tapered-bore (1:30) execution on AH24036 withdrawal sleeve; same ISO 15 envelope, separate order number. |
| C4036-V | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | SKF CARB toroidal bearing C 4036 V shares the 180×280×100 mm envelope but catalogue C/C0 differ (1320/2120 kN vs 1134/1730 kN); it floats axially and cannot locate the shaft — pair, never swap one-for-one. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 24036 model number is decoded
In SKF catalogue PUB BU/P1 17000, 24036 appears as 24036 CC/W33: an open, double-row spherical roller bearing, self-aligning by virtue of the sphered outer raceway, sized 180×280×100 mm to the ISO 15 boundary plan. Reading the designation: the leading 2 marks a spherical roller bearing, the 40 is the ISO 15 dimension series (dimension series 40 (compact OD, maximum width)), and the last two digits encode the 180 mm bore; the 280 mm OD and 100 mm width follow the ISO 15 general plan. SKF basic executions here are CC/W33; specialist suffixes change the bearing materially — VA405 for vibrating screens (C4 clearance, surface-hardened cage), 2CS5 for the sealed variant — and must be quoted in full when ordering. The 156 kN Pu figure feeds the adjusted-life equation at contaminated or partial-film conditions, and the 1.53 C0/C balance shows this execution is tuned to heavy radial-plus-axial duty with misalignment tolerance. After mounting, swing the outer ring to confirm free self-alignment: the 24036 should tilt through its full catalogue misalignment range without binding; a stiff joint signals a cocked seat or shoulder interference.
Typical equipment & failure modes
Common applications
- steel-plant continuous-caster segments
- large induced-draft fan rotors
- SAG and ball-mill drive shafts
- large mining crusher main shafts
Known failure patterns
- raceway fatigue spalling of the sphered outer raceway after extended service above the catalogue L10 rating
- inner-ring raceway spalling from edge loading when misalignment exceeds the self-aligning recovery range
- cage pocket wear or fracture from roller skew at insufficient minimum load or rapid acceleration
- roller-end scoring from starved lubricant at start-up before the grease channel purges
- false brinelling on standby machines exposed to external vibration
Selection pitfalls — read before you substitute
- At 180 mm bore the ring mass makes cocking during mounting a real risk; guide the bearing square, confirm seat contact around the full circumference, and re-check the self-aligning swing after the housing cap is torqued down.
- The 24000-series series at 180 mm bore (280×100 mm) packs maximum roller length into the smallest OD envelope — very high C0 for its size but the lowest speed ceiling; never swap it for a wider-OD 231 bearing without re-checking the housing bore and the speed margin.
- Never use the tapered-bore CCK30/K30 variant's drive-up figures on this cylindrical-bore 24036; clearance reduction targets differ, and over-driving a cylindrical bore onto an oversized journal cracks the inner ring.
- The 24036 shares its ISO 15 envelope across brands, but internal geometry differs — SKF load ratings in this row are 1134/1730 kN; another maker's same-size bearing may rate higher or lower, so do not interchange on envelope alone.
- The 1134/1730 kN ratings are SKF catalogue values for this exact execution (24036 CC/W33); SKF can revise internal geometry without changing the order number, so keep the catalogue version (SKF catalogue PUB BU/P1 17000) with the specification and re-verify for critical drives.
- SKF lists several executions of 24036 (cylindrical bore as listed, tapered-bore 24036 CCK30/W33 variant, plus sealed and vibrating-screen options in the same envelope); they are not interchangeable order numbers — quote the full 24036 CC/W33 designation when purchasing.
Frequently asked questions
What are the dimensions and catalogue data of 24036?
The 24036 CC/W33 is a double-row spherical roller bearing with 180 mm bore, 280 mm outer diameter and 100 mm width (7.087 × 11.024 × 3.937 in) per ISO 15. From SKF catalogue PUB BU/P1 17000: basic dynamic load rating C 1134 kN, C0 1730 kN, fatigue load limit Pu 156 kN, reference speed 1,500 r/min, limiting speed 2,200 r/min, mass about 23000 g. It is an open, self-aligning bearing with two pressed-steel cages with a floating guide ring.
How does the 24036 bore code work?
The last two digits of 24036 are bore code 36, so 36 × 5 = 180 mm bore. The 280 mm OD and 100 mm width come from the ISO 15 dimension-series plan (dimension series 40 (compact OD, maximum width)), shared with other spherical roller bearings of the same code.
What does the CC/W33 suffix mean on 24036?
CC denotes two pressed-steel cages with a floating guide ring between the roller rows, and W33 adds an annular groove plus three lubrication holes in the outer ring for relubrication. In dimension series 40/41 the tapered-bore counterpart carries CCK30/W33 with a 1:30 taper.
Can 24036 accommodate misalignment and axial load?
Yes on both counts. The sphered outer raceway lets the bearing self-align ≈ 0.5–2.5° depending on series, absorbing shaft deflection and housing-seat errors. The two barrel-roller rows also carry bidirectional axial load in addition to heavy radial load — this is the key difference from cylindrical roller bearings, which take no axial load.
When should the tapered-bore 24036K30 variant be used instead?
Choose the K30 (1:30 tapered bore) variant when the bearing must seat on an adapter or withdrawal sleeve — typical for long shafts, frequent dismounting, or stepped shafts where machining a precision journal is impractical. Sleeve mounting requires measuring clearance reduction or axial drive-up, not nut torque. The cylindrical-bore 24036 listed here seats directly on a machined journal.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 9.1 spherical roller bearings on 2026-09-26. Read our editorial & correction policy.