24064EMD1 bearing: complete specifications & equivalents
The 24064EMD1 is a ISO 15 radial bearing sized 320 x 480 x 160 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 320 mm |
| Outer diameter D | 480 mm |
| Width B | 160 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | brass, machined (M1) |
| Basic dynamic load rating C | 3250 kN |
| Basic static load rating C0 | 5400 kN |
| Fatigue load limit Pu | 184 kN |
| Limiting speed (mechanical) | 720 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 104000 g |
| Manufacturer designation | NTN 24064EMD1 |
| Standard | ISO 15 |
| Catalog version | NTN Ball and Roller Bearings CAT.No.2203E |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203E) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203E); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 24000-series range
| Bore d | 12.598 in |
|---|---|
| Outer diameter D | 18.898 in |
| Width B | 6.299 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 80 mm |
| Smallest bore in 24000-series | 65 mm |
| Largest outer diameter in 24000-series | 1580 mm |
| Width range across 24000-series | 35–462 mm |
| Bore position in 24000-series (smallest first) | 19 of 42 |
| Bore above smallest 24000-series size | 255 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 24064EMK30D1 | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same NTN 24000-series envelope, cage and ratings; this is the cylindrical-bore execution of the tapered-bore 24064EMK30D1 (K/K30 sleeve or tapered-seat mounting). Verify shaft arrangement. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 24064EMD1 model number is decoded
24064EMD1 is the EM machined-brass-cage execution of NTN's spherical roller range for a 320 mm shaft — 3250 kN basic dynamic capacity in a 104000 g, open ISO 15 envelope. On the NTN nameplate the suffix cluster after the size reads in order: cage design (EM), bore (cylindrical), lubrication feature (D1); 24064EMD1 is assembled exactly in that order. Two symmetric roller rows share the load: C 3250 kN, C0 5400 kN (C0/C ≈ 1.66), with useful axial capacity in either direction alongside the dominant radial load. With about 10.2 kN of C per millimetre of the 320 mm bore, 24064EMD1 screens interchange candidates quickly — then verify cage (EA/EM), bore (K/K30) and lubrication feature (D1/W33) suffixes. Fit the cylindrical-bore 24064EMD1 with the inner ring heated (max 120 °C) for the shaft interference; the outer ring slides into the housing with its spherical seat able to pivot after seating.
Typical equipment & failure modes
Common applications
- cement-rotary-kiln support and trunnion rolls
- large SAG/ball-mill trunnion and pinion shafts
- heavy vibrating screens and grizzly feeders
- offshore and marine propulsion shaftlines
Known failure patterns
- lubricant starvation at the centre rib area when the D1/W33 groove is not connected to a relubrication supply
- machined EM cage wear from inadequate oil film at the cage-guiding surfaces
- roller-end smearing during skidding starts under light load and high viscosity grease
- rolling-contact fatigue after the catalogue L10 life at the actual load
- false brinelling on stopped machines exposed to screen or crusher vibration
Selection pitfalls — read before you substitute
- At 320 mm bore 24064EMD1 is normally mounted on adapter/withdrawal sleeves with hydraulic assistance; follow the NTN drive-up angle or oil-injection procedure — manual nut tightening cannot set the multi-tonne seating correctly.
- The D1/W33 groove only helps if the housing has a matching grease passage; mounting a D1 24064EMD1 in a solid block with no port wastes the feature and leaves the centre rows under-lubricated.
- Adapter-sleeve mounting requires the correct sleeve series and locknut for the 320 mm shaft; a sleeve sized to bore alone ignores thread, width and the oil-injection option on large K30 seats.
- Adapter-sleeve mounting requires the correct sleeve series and locknut for the 320 mm shaft; a sleeve sized to bore alone ignores thread, width and the oil-injection option on large K30 seats.
- Adapter-sleeve mounting requires the correct sleeve series and locknut for the 320 mm shaft; a sleeve sized to bore alone ignores thread, width and the oil-injection option on large K30 seats.
- The 3250/5400 kN ratings, 184 kN Pu and 104000 g mass are NTN Ball and Roller Bearings CAT.No.2203E values for 24064EMD1 (EM machined-brass-cage/D1); another maker's same-envelope part revises internal geometry, so re-verify ratings and cage before substitution on vibrating or rated drives.
Frequently asked questions
What are the dimensions and catalogue data of 24064EMD1?
24064EMD1 is an NTN double-row spherical roller bearing to ISO 15: 320 mm bore, 480 mm OD and 160 mm width (12.598 × 18.898 × 6.299 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 3250 kN, C0 5400 kN, Pu 184 kN, grease limiting speed 720 r/min, oil 920 r/min, mass about 104000 g. It is open, with one-piece machined brass cage (EM high-capacity design).
What is the difference between the K/K30 tapered bore and the cylindrical bore versions?
24064EMD1 has a cylindrical bore and mounts directly on a machined shaft seat. Its tapered-bore counterpart is 24064EMK30D1 (K = 1:12, or K30 = 1:30 on the wide series), intended for adapter/withdrawal-sleeve mounting.
What do EA and EM mean on NTN spherical roller bearings?
EA is the NTN standard-capacity/high-capacity execution with a pressed sheet-steel window cage; EM is the high-capacity execution with a one-piece machined brass cage. Both use the optimised symmetric-roller design, but cage identity changes mass, speed behaviour and suitability for duties like vibrating screens, so they are separate order numbers. 24064EMD1 is the EM machined-brass-cage execution, listed with the ＊ ULTAGE new-generation mark.
What do D1 and W33 mean on 24064EMD1?
D1 is NTN's outer-ring lubrication feature: an annular groove with oil holes around the outer ring, aligned with a housing grease port so lubricant reaches both roller rows directly. 24064EMD1 carries D1; W33 is the equivalent industry-spelled annular-groove-and-holes feature seen on other executions.
How much misalignment and axial load can 24064EMD1 take?
The sphered outer raceway compensates static and dynamic misalignment in the order of 1–2° (verify the exact 2203E figure for the 24000 series); beyond that, load concentrates on one roller row. Load is predominantly radial with a moderate axial share in either direction — 3250 kN C / 5400 kN C0 — but sustained pure axial load is not recommended because it unloads one row.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN Ball and Roller Bearings CAT.No.2203E on 2026-10-01. Read our editorial & correction policy.