24076EMD1 bearing: complete specifications & equivalents
The 24076EMD1 is a ISO 15 radial bearing sized 380 x 560 x 180 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 380 mm |
| Outer diameter D | 560 mm |
| Width B | 180 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | brass, machined (M1) |
| Basic dynamic load rating C | 4140 kN |
| Basic static load rating C0 | 7280 kN |
| Fatigue load limit Pu | 240 kN |
| Limiting speed (mechanical) | 610 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 154000 g |
| Manufacturer designation | NTN 24076EMD1 |
| Standard | ISO 15 |
| Catalog version | NTN Ball and Roller Bearings CAT.No.2203E |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203E) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203E); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 24000-series range
| Bore d | 14.961 in |
|---|---|
| Outer diameter D | 22.047 in |
| Width B | 7.087 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 90 mm |
| Smallest bore in 24000-series | 65 mm |
| Largest outer diameter in 24000-series | 1580 mm |
| Width range across 24000-series | 35–462 mm |
| Bore position in 24000-series (smallest first) | 22 of 42 |
| Bore above smallest 24000-series size | 315 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 24076EMK30D1 | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same NTN 24000-series envelope, cage and ratings; this is the cylindrical-bore execution of the tapered-bore 24076EMK30D1 (K/K30 sleeve or tapered-seat mounting). Verify shaft arrangement. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 24076EMD1 model number is decoded
24076EMD1 is the EM machined-brass-cage execution of NTN's spherical roller range for a 380 mm shaft — 4140 kN basic dynamic capacity in a 154000 g, open ISO 15 envelope. On the NTN nameplate the suffix cluster after the size reads in order: cage design (EM), bore (cylindrical), lubrication feature (D1); 24076EMD1 is assembled exactly in that order. The 90.0 mm radial section over the 380 mm bore carries two roller rows; capacity per millimetre of bore is about 10.9 kN/mm, among the highest of rolling bearings for the ISO 15 envelope. Catalogue mass 154000 g (154.00 kg) for the 380×560×180 mm execution includes the EM machined-brass-cage cage and both roller rows; shaft and housing shoulders must support that ring squarely. Fit the cylindrical-bore 24076EMD1 with the inner ring heated (max 120 °C) for the shaft interference; the outer ring slides into the housing with its spherical seat able to pivot after seating.
Typical equipment & failure modes
Common applications
- large SAG/ball-mill trunnion and pinion shafts
- heavy vibrating screens and grizzly feeders
- offshore and marine propulsion shaftlines
- large wind-turbine main-shaft arrangements
Known failure patterns
- raceway spalling at the roller ends when misalignment or deflection concentrates the line contact
- cage damage when a mounting force is applied through the roller set instead of the ring face
- micro-pitting when the EHL film is thinner than the raceway composite roughness
- rolling-contact fatigue after the catalogue L10 life at the actual load
- hard-particle indentation through the open arrangement in dusty mining duty
Selection pitfalls — read before you substitute
- At 380 mm bore 24076EMD1 is normally mounted on adapter/withdrawal sleeves with hydraulic assistance; follow the NTN drive-up angle or oil-injection procedure — manual nut tightening cannot set the multi-tonne seating correctly.
- Minimum load must be maintained even at rest under vibration: an unloaded 24076EMD1 on a stopped screen false-brinells; parking brakes and shaker isolation both matter.
- Do not confuse EA and EM at the same number: 24076EMD1 carries EM machined-brass-cage; swapping to the other cage execution changes mass, speed behaviour and sometimes suitability for vibration, even though the 380×560 mm envelope is identical.
- The two roller rows must share load equally — a tilted spacer or unequal abutment on the 180 mm-wide ring loads one row only and shows as asymmetric race polish during inspection.
- The cylindrical-bore 24076EMD1 and its tapered-bore counterpart 24076EMK30D1 share envelope and ratings but not mounting: do not order the K variant unless the drawing specifies a sleeve or tapered seat.
- The 4140/7280 kN ratings, 240 kN Pu and 154000 g mass are NTN Ball and Roller Bearings CAT.No.2203E values for 24076EMD1 (EM machined-brass-cage/D1); another maker's same-envelope part revises internal geometry, so re-verify ratings and cage before substitution on vibrating or rated drives.
Frequently asked questions
What are the dimensions and catalogue data of 24076EMD1?
24076EMD1 is an NTN double-row spherical roller bearing to ISO 15: 380 mm bore, 560 mm OD and 180 mm width (14.961 × 22.047 × 7.087 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 4140 kN, C0 7280 kN, Pu 240 kN, grease limiting speed 610 r/min, oil 780 r/min, mass about 154000 g. It is open, with one-piece machined brass cage (EM high-capacity design).
What is the difference between the K/K30 tapered bore and the cylindrical bore versions?
24076EMD1 has a cylindrical bore and mounts directly on a machined shaft seat. Its tapered-bore counterpart is 24076EMK30D1 (K = 1:12, or K30 = 1:30 on the wide series), intended for adapter/withdrawal-sleeve mounting.
What do EA and EM mean on NTN spherical roller bearings?
EA is the NTN standard-capacity/high-capacity execution with a pressed sheet-steel window cage; EM is the high-capacity execution with a one-piece machined brass cage. Both use the optimised symmetric-roller design, but cage identity changes mass, speed behaviour and suitability for duties like vibrating screens, so they are separate order numbers. 24076EMD1 is the EM machined-brass-cage execution, listed with the ＊ ULTAGE new-generation mark.
What do D1 and W33 mean on 24076EMD1?
D1 is NTN's outer-ring lubrication feature: an annular groove with oil holes around the outer ring, aligned with a housing grease port so lubricant reaches both roller rows directly. 24076EMD1 carries D1; W33 is the equivalent industry-spelled annular-groove-and-holes feature seen on other executions.
How much misalignment and axial load can 24076EMD1 take?
The sphered outer raceway compensates static and dynamic misalignment in the order of 1–2° (verify the exact 2203E figure for the 24000 series); beyond that, load concentrates on one roller row. Load is predominantly radial with a moderate axial share in either direction — 4140 kN C / 7280 kN C0 — but sustained pure axial load is not recommended because it unloads one row.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN Ball and Roller Bearings CAT.No.2203E on 2026-10-01. Read our editorial & correction policy.