24080-ECCK30J-W33 bearing: complete specifications & equivalents
The 24080-ECCK30J-W33 is a ISO 15 radial bearing sized 400 x 600 x 200 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 400 mm |
| Outer diameter D | 600 mm |
| Width B | 200 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 4507 kN |
| Basic static load rating C0 | 8000 kN |
| Fatigue load limit Pu | 560 kN |
| Reference speed (thermal) | 630 rpm |
| Limiting speed (mechanical) | 900 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 220000 g |
| Manufacturer designation | SKF 24080 ECCK30J/W33 |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 9.3 withdrawal-sleeve executions |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 9.3 withdrawal-sleeve executions) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 9.3 withdrawal-sleeve executions); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 24000-series range
| Bore d | 15.748 in |
|---|---|
| Outer diameter D | 23.622 in |
| Width B | 7.874 in |
| ISO bore code | 80 |
| Radial section height (D−d)/2 | 100 mm |
| Smallest bore in 24000-series | 65 mm |
| Largest outer diameter in 24000-series | 700 mm |
| Width range across 24000-series | 35–218 mm |
| Bore position in 24000-series (smallest first) | 23 of 27 |
| Bore above smallest 24000-series size | 335 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 24080 | SKF | full Dimensions and internal design equivalent — standard interchange. | Tapered-bore (1:30) sleeve-mounted execution of 24080; identical ISO 15 envelope, fits AOH24080 withdrawal sleeve on a 380 mm shaft. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 24080-ECCK30J-W33 model number is decoded
24080-ecck30j-w33 is the 1:30 tapered-bore execution of the 24000-series spherical roller bearing: the same two barrel-roller rows on a sphered outer raceway as 24080-ecck30j-w33, but the inner-ring bore tapers 1 mm per 30 mm for adapter- or withdrawal-sleeve mounting, as listed by SKF in SKF catalogue PUB BU/P1 17000. Reading the designation: the leading 2 marks a spherical roller bearing, the 40 is the ISO 15 dimension series (dimension series 40 (compact OD, maximum width)), and the last two digits encode the 400 mm bore; the 600 mm OD and 200 mm width follow the ISO 15 general plan. Reading the suffix on 24080-ecck30j-w33, the K30 (or EK/CCK30) element changes only the bore — 1:30 taper for sleeve mounting — while the rest of the suffix chain (CC cages with W33 groove) keeps the same internal design, cage and W33 relubrication features as the cylindrical-bore 24080-ecck30j-w33. The 100.0 mm radial section height ((600−400)/2) and 220000 g catalogue mass frame a 400 mm bore bearing rated at 4507 kN C — roughly 11.27 kN of dynamic capacity per millimetre of bore before application factors. Because driving up the 1:30 taper consumes radial clearance, K30 executions are commonly ordered with C3 initial clearance so the residual running clearance after mounting matches the cylindrical-bore 24080-ecck30j-w33 on an interference seat.
Typical equipment & failure modes
Common applications
- wind-turbine main shaft support
- heavy rolling-mill work-roll chocks
- stepped shafts fitted with withdrawal sleeves against a fixed shoulder
- fan and pulley shafts that need periodic bearing removal in the field
Known failure patterns
- raceway fatigue spalling of the sphered outer raceway after extended service above the catalogue L10 rating
- inner-ring raceway spalling from edge loading when misalignment exceeds the self-aligning recovery range
- inner-ring circumferential cracking after over-drive on the tapered seat removes too much radial clearance and the bearing runs preloaded
- roller-end scoring from starved lubricant at start-up before the grease channel purges
- brinelling from static overload or impact during handling and mounting
Selection pitfalls — read before you substitute
- At 400 mm bore the ring mass makes cocking during mounting a real risk; guide the bearing square, confirm seat contact around the full circumference, and re-check the self-aligning swing after the housing cap is torqued down.
- The 24000-series series at 400 mm bore (600×200 mm) packs maximum roller length into the smallest OD envelope — very high C0 for its size but the lowest speed ceiling; never swap it for a wider-OD 231 bearing without re-checking the housing bore and the speed margin.
- Never apply the drive-up or clearance-reduction figures for this 1:30 tapered 24080-ecck30j-w33 to a bearing of the other taper (1:12 vs 1:30); the steeper taper moves far less clearance per nut turn and the targets come from different catalogue tables.
- A loose sleeve after the first weeks of service usually means inadequate initial drive-up; re-checking clearance without dismounting is possible through the 200 mm-wide roller rows with feeler gauges — do not simply tighten the KM nut until vibration stops.
- Shaft and housing fillets must clear the bearing chamfer so the 200 mm-wide rings seat square; use an undercut or withdrawal groove rather than an oversized radius that locks on the ring face.
- The 4507/8000 kN ratings are SKF catalogue values for this tapered-bore execution (SKF 24080 ECCK30J/W33); sleeve, KM nut and MB washer are separate order numbers, and the catalogue version (SKF catalogue PUB BU/P1 17000) should travel with the mounting specification.
Frequently asked questions
What are the dimensions and catalogue data of 24080-ecck30j-w33?
The SKF 24080 ECCK30J/W33 is a double-row spherical roller bearing with a 1:30 tapered bore, 400 mm nominal bore, 600 mm outer diameter and 200 mm width (15.748 × 23.622 × 7.874 in) per ISO 15. From SKF catalogue PUB BU/P1 17000: C 4507 kN, C0 8000 kN, Pu 560 kN, reference speed 630 r/min, limiting speed 900 r/min, mass about 220000 g. It is mounted on an adapter (H) or withdrawal (AH) sleeve, not directly on the shaft.
What does the K30 suffix mean on 24080-ecck30j-w33?
K30 (written CCK30/W33 in the CC execution) marks the 1:30 tapered bore for sleeve mounting. The bearing seats on an H-series adapter sleeve with a KM locknut and MB lock washer (plain shaft, h9 tolerance), or on an AH withdrawal sleeve against a shaft shoulder.
Which adapter sleeve fits the 24080-ecck30j-w33?
The sleeve is selected by the actual shaft diameter in millimetres, not only by the 400 mm nominal bore: SKF H-sleeve numbers each cover a small shaft-diameter range and are width-series specific (H39/H30/H31/H32 matching dimension series 39/40/31/32), and each kit bundles the sleeve, KM locknut and MB lock washer. For shoulder locations use an AH withdrawal sleeve instead. Confirm the sleeve number against the SKF catalogue PUB BU/P1 17000 mounting tables for your shaft size.
How is the 24080-ecck30j-w33 driven up and checked?
Mounting is controlled by radial-clearance reduction or axial drive-up distance from the SKF catalogue tables for the 1:30 taper, never by locknut torque. Measure clearance with feeler gauges before and after tightening the KM nut, stop at the tabulated decrease, and lock the MB washer tab. Over-drive removes too much clearance (inner-ring cracking risk); under-drive lets the sleeve creep and fret.
What is the difference between 24080-ecck30j-w33 and 24080-ecck30j-w33?
They share the ISO 15 envelope and the same 4507/8000 kN ratings, but 24080-ecck30j-w33 has the 1:30 tapered bore for sleeve mounting on a plain shaft, while 24080-ecck30j-w33 has a cylindrical bore for direct mounting on a machined interference journal (typically m6 with H7 housing). They are separate order numbers, not interchangeable in the same shaft arrangement.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 9.3 withdrawal-sleeve executions on 2026-09-26. Read our editorial & correction policy.