24126EMD1 bearing: complete specifications & equivalents
The 24126EMD1 is a ISO 15 radial bearing sized 130 x 210 x 80 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 130 mm |
| Outer diameter D | 210 mm |
| Width B | 80 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | brass, machined (M1) |
| Basic dynamic load rating C | 803 kN |
| Basic static load rating C0 | 1080 kN |
| Fatigue load limit Pu | 45 kN |
| Limiting speed (mechanical) | 1800 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 10700 g |
| Manufacturer designation | NTN 24126EMD1 |
| Standard | ISO 15 |
| Catalog version | NTN Ball and Roller Bearings CAT.No.2203E |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203E) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203E); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 24100-series range
| Bore d | 5.118 in |
|---|---|
| Outer diameter D | 8.268 in |
| Width B | 3.15 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 40 mm |
| Smallest bore in 24100-series | 100 mm |
| Largest outer diameter in 24100-series | 1150 mm |
| Width range across 24100-series | 65–438 mm |
| Bore position in 24100-series (smallest first) | 4 of 32 |
| Bore above smallest 24100-series size | 30 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 24126EMK30D1 | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same NTN 24100-series envelope, cage and ratings; this is the cylindrical-bore execution of the tapered-bore 24126EMK30D1 (K/K30 sleeve or tapered-seat mounting). Verify shaft arrangement. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 24126EMD1 model number is decoded
24126EMD1 belongs to the 24100 series of NTN spherical rollers and carries the ＊ ULTAGE new-generation mark in the 2203E table: self-aligning, high radial capacity, moderate axial load in either direction. On the NTN nameplate the suffix cluster after the size reads in order: cage design (EM), bore (cylindrical), lubrication feature (D1); 24126EMD1 is assembled exactly in that order. The cylindrical bore fits a machined 130 mm shaft seat directly; the same envelope in 24126EMK30D1 (tapered) is the sleeve-mounted alternative when clearance must be set by drive-up. Selection: the C0/C ratio of 1.34 (1080/803 kN) reflects the heavy static and shock proportioning of 24126EMD1; size the equivalent load at the required L10 with shock factor for the application. Never mount 24126EMD1 by striking the outer ring through the roller set; drive through ring faces (or the adapter sleeve nut) and support the ring square to avoid brinelling the 210 mm race.
Typical equipment & failure modes
Common applications
- large SAG/ball-mill trunnion and pinion shafts
- heavy vibrating screens and grizzly feeders
- offshore and marine propulsion shaftlines
- large wind-turbine main-shaft arrangements
Known failure patterns
- raceway spalling at the roller ends when misalignment or deflection concentrates the line contact
- machined EM cage wear from inadequate oil film at the cage-guiding surfaces
- roller-end smearing during skidding starts under light load and high viscosity grease
- brinelling from static overload or a hammer blow during sleeve mounting
- false brinelling on stopped machines exposed to screen or crusher vibration
Selection pitfalls — read before you substitute
- At 130 mm bore 24126EMD1 is normally mounted on adapter/withdrawal sleeves with hydraulic assistance; follow the NTN drive-up angle or oil-injection procedure — manual nut tightening cannot set the multi-tonne seating correctly.
- Oil relubrication toward 2,400 r/min needs drain and level design; flooding the 80 mm cavity churns heat through the heavy roller set and cage despite the higher oil speed figure.
- K and K30 are different tapers — K is 1:12 and K30 is 1:30 on the wide series; an adapter sleeve for one will not mount the other 130 mm bearing, and drive-up procedures differ.
- The two roller rows must share load equally — a tilted spacer or unequal abutment on the 80 mm-wide ring loads one row only and shows as asymmetric race polish during inspection.
- Do not confuse EA and EM at the same number: 24126EMD1 carries EM machined-brass-cage; swapping to the other cage execution changes mass, speed behaviour and sometimes suitability for vibration, even though the 130×210 mm envelope is identical.
- The 803/1080 kN ratings, 45 kN Pu and 10700 g mass are NTN Ball and Roller Bearings CAT.No.2203E values for 24126EMD1 (EM machined-brass-cage/D1); another maker's same-envelope part revises internal geometry, so re-verify ratings and cage before substitution on vibrating or rated drives.
Frequently asked questions
What are the dimensions and catalogue data of 24126EMD1?
24126EMD1 is an NTN double-row spherical roller bearing to ISO 15: 130 mm bore, 210 mm OD and 80 mm width (5.118 × 8.268 × 3.15 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 803 kN, C0 1080 kN, Pu 45 kN, grease limiting speed 1,800 r/min, oil 2,400 r/min, mass about 10700 g. It is open, with one-piece machined brass cage (EM high-capacity design).
What is the difference between the K/K30 tapered bore and the cylindrical bore versions?
24126EMD1 has a cylindrical bore and mounts directly on a machined shaft seat. Its tapered-bore counterpart is 24126EMK30D1 (K = 1:12, or K30 = 1:30 on the wide series), intended for adapter/withdrawal-sleeve mounting.
What do EA and EM mean on NTN spherical roller bearings?
EA is the NTN standard-capacity/high-capacity execution with a pressed sheet-steel window cage; EM is the high-capacity execution with a one-piece machined brass cage. Both use the optimised symmetric-roller design, but cage identity changes mass, speed behaviour and suitability for duties like vibrating screens, so they are separate order numbers. 24126EMD1 is the EM machined-brass-cage execution, listed with the ＊ ULTAGE new-generation mark.
What do D1 and W33 mean on 24126EMD1?
D1 is NTN's outer-ring lubrication feature: an annular groove with oil holes around the outer ring, aligned with a housing grease port so lubricant reaches both roller rows directly. 24126EMD1 carries D1; W33 is the equivalent industry-spelled annular-groove-and-holes feature seen on other executions.
How much misalignment and axial load can 24126EMD1 take?
The sphered outer raceway compensates static and dynamic misalignment in the order of 1–2° (verify the exact 2203E figure for the 24100 series); beyond that, load concentrates on one roller row. Load is predominantly radial with a moderate axial share in either direction — 803 kN C / 1080 kN C0 — but sustained pure axial load is not recommended because it unloads one row.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN Ball and Roller Bearings CAT.No.2203E on 2026-10-01. Read our editorial & correction policy.