24136EMK30D1 bearing: complete specifications & equivalents
The 24136EMK30D1 is a ISO 15 radial bearing sized 180 x 300 x 118 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 180 mm |
| Outer diameter D | 300 mm |
| Width B | 118 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | brass, machined (M1) |
| Basic dynamic load rating C | 1660 kN |
| Basic static load rating C0 | 2290 kN |
| Fatigue load limit Pu | 85.5 kN |
| Limiting speed (mechanical) | 1300 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 33000 g |
| Manufacturer designation | NTN 24136EMK30D1 |
| Standard | ISO 15 |
| Catalog version | NTN Ball and Roller Bearings CAT.No.2203E |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203E) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203E); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 24100-series range
| Bore d | 7.087 in |
|---|---|
| Outer diameter D | 11.811 in |
| Width B | 4.646 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 60 mm |
| Smallest bore in 24100-series | 100 mm |
| Largest outer diameter in 24100-series | 1150 mm |
| Width range across 24100-series | 65–438 mm |
| Bore position in 24100-series (smallest first) | 9 of 32 |
| Bore above smallest 24100-series size | 80 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 24136EMD1 | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same NTN 24100-series envelope, cage and ratings; this is the tapered-bore execution (K30, 1:30) of the cylindrical-bore 24136EMD1 — mounting (adapter/withdrawal sleeve or tapered seat, drive-up) differs. Verify shaft arrangement. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 24136EMK30D1 model number is decoded
The NTN order number 24136EMK30D1 identifies a 180×300×118 mm (7.087 × 11.811 × 4.646 in) spherical roller bearing, 1:30 tapered bore (K30), to the ISO 15 boundary plan. Numbering ties 24136EMK30D1 to its envelope and execution: same-number EA versus EM or plain variants share the 180 mm bore but differ in cage and sometimes mass, so they are quoted as separate articles. At 1660 kN C and 33000 g mass the 24100 series part is built for shock and vibration; the 118 mm-wide ring needs square abutments to keep both rows equally loaded. Pu 85.5 kN against C0 2290 kN anchors the contamination derating; for dirty mining duty the adjusted life of 24136EMK30D1 moves with cleanliness far more than with small C variations. On vibrating-duty shafts verify the radial clearance class and cage choice at order time; the open 24136EMK30D1 leaves sealing and the C3/C4 clearance decision to the application drawing.
Typical equipment & failure modes
Common applications
- large SAG/ball-mill trunnion and pinion shafts
- heavy vibrating screens and grizzly feeders
- offshore and marine propulsion shaftlines
- large wind-turbine main-shaft arrangements
Known failure patterns
- raceway spalling at the roller ends when misalignment or deflection concentrates the line contact
- pressed EA cage fatigue under sustained vibration when minimum load is not maintained
- sliding wear and heat when relubrication intervals ignore the groove (D1/W33) supply path
- asymmetric wear on the two roller rows from sustained angular misalignment beyond the self-aligning range
- brinelling from static overload or a hammer blow during sleeve mounting
Selection pitfalls — read before you substitute
- At 180 mm bore 24136EMK30D1 is normally mounted on adapter/withdrawal sleeves with hydraulic assistance; follow the NTN drive-up angle or oil-injection procedure — manual nut tightening cannot set the multi-tonne seating correctly.
- Do not confuse EA and EM at the same number: 24136EMK30D1 carries EM machined-brass-cage; swapping to the other cage execution changes mass, speed behaviour and sometimes suitability for vibration, even though the 180×300 mm envelope is identical.
- The 1:30 tapered bore is the only difference from the cylindrical-bore 24136EMD1: envelopes and ratings match, but drive-up tooling, sleeve and seat do not — never mix the two mounting methods.
- Oil relubrication toward 1,600 r/min needs drain and level design; flooding the 118 mm cavity churns heat through the heavy roller set and cage despite the higher oil speed figure.
- Open spherical rollers swallow dust in mining duty; specify labyrinth or taconite seals externally, or the 1,300 r/min grease rating is lost to abrasive wear long before fatigue.
- The 1660/2290 kN ratings, 85.5 kN Pu and 33000 g mass are NTN Ball and Roller Bearings CAT.No.2203E values for 24136EMK30D1 (EM machined-brass-cage/D1); another maker's same-envelope part revises internal geometry, so re-verify ratings and cage before substitution on vibrating or rated drives.
Frequently asked questions
What are the dimensions and catalogue data of 24136EMK30D1?
24136EMK30D1 is an NTN double-row spherical roller bearing to ISO 15: 180 mm bore, 300 mm OD and 118 mm width (7.087 × 11.811 × 4.646 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 1660 kN, C0 2290 kN, Pu 85.5 kN, grease limiting speed 1,300 r/min, oil 1,600 r/min, mass about 33000 g. It is open, with one-piece machined brass cage (EM high-capacity design) and a 1:30 tapered bore.
What is the difference between the K/K30 tapered bore and the cylindrical bore versions?
K30 denotes a 1:30 tapered bore (the wide 24100 series). 24136EMK30D1 mounts on a matching adapter or withdrawal sleeve on a plain 180 mm shaft and is driven up to a measured radial clearance; the cylindrical-bore counterpart is 24136EMD1.
What do EA and EM mean on NTN spherical roller bearings?
EA is the NTN standard-capacity/high-capacity execution with a pressed sheet-steel window cage; EM is the high-capacity execution with a one-piece machined brass cage. Both use the optimised symmetric-roller design, but cage identity changes mass, speed behaviour and suitability for duties like vibrating screens, so they are separate order numbers. 24136EMK30D1 is the EM machined-brass-cage execution, listed with the ＊ ULTAGE new-generation mark.
What do D1 and W33 mean on 24136EMK30D1?
D1 is NTN's outer-ring lubrication feature: an annular groove with oil holes around the outer ring, aligned with a housing grease port so lubricant reaches both roller rows directly. 24136EMK30D1 carries D1; W33 is the equivalent industry-spelled annular-groove-and-holes feature seen on other executions.
How much misalignment and axial load can 24136EMK30D1 take?
The sphered outer raceway compensates static and dynamic misalignment in the order of 1–2° (verify the exact 2203E figure for the 24100 series); beyond that, load concentrates on one roller row. Load is predominantly radial with a moderate axial share in either direction — 1660 kN C / 2290 kN C0 — but sustained pure axial load is not recommended because it unloads one row.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN Ball and Roller Bearings CAT.No.2203E on 2026-10-01. Read our editorial & correction policy.