24152 bearing: complete specifications & equivalents
The 24152 is a ISO 15 radial bearing sized 260 x 440 x 180 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 260 mm |
| Outer diameter D | 440 mm |
| Width B | 180 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 3086 kN |
| Basic static load rating C0 | 4800 kN |
| Fatigue load limit Pu | 380 kN |
| Reference speed (thermal) | 670 rpm |
| Limiting speed (mechanical) | 950 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 110000 g |
| Manufacturer designation | SKF 24152 CC/W33 |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 9.1 spherical roller bearings |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 9.1 spherical roller bearings) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 9.1 spherical roller bearings); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 24100-series range
| Bore d | 10.236 in |
|---|---|
| Outer diameter D | 17.323 in |
| Width B | 7.087 in |
| ISO bore code | 52 |
| Radial section height (D−d)/2 | 90 mm |
| Smallest bore in 24100-series | 100 mm |
| Largest outer diameter in 24100-series | 790 mm |
| Width range across 24100-series | 65–308 mm |
| Bore position in 24100-series (smallest first) | 14 of 25 |
| Bore above smallest 24100-series size | 160 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 24152 | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; D/B cross-verified against Schaeffler HR1 2022; brand-specific OEM equivalents (NSK/FAG/NTN) pending multi-source data. |
| 24152-CCK30-W33 | SKF | full Dimensions and internal design equivalent — standard interchange. | Tapered-bore (1:30) execution on AOH24152 withdrawal sleeve; same ISO 15 envelope, separate order number. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 24152 model number is decoded
Ordering number 24152 CC/W33 in SKF catalogue PUB BU/P1 17000 denotes a double-row spherical roller bearing for a 260 mm shaft, dimension series 41 (medium OD, maximum width), with open execution and two pressed-steel cages with a floating guide ring. The code breaks down as type digit 2 (double-row spherical roller), dimension series 41 (dimension series 41 (medium OD, maximum width)), and bore code 52 = 260 mm; dimensions 260×440×180 mm therefore match the ISO 15 envelope. SKF basic executions here are CC/W33; specialist suffixes change the bearing materially — VA405 for vibrating screens (C4 clearance, surface-hardened cage), 2CS5 for the sealed variant — and must be quoted in full when ordering. The 380 kN Pu figure feeds the adjusted-life equation at contaminated or partial-film conditions, and the 1.56 C0/C balance shows this execution is tuned to heavy radial-plus-axial duty with misalignment tolerance. The cylindrical-bore execution here seats directly on the shaft journal; if the application calls for an adapter sleeve, order the tapered-bore 24152 CCK30/W33 variant instead and measure the drive-up or clearance reduction, not the nut torque.
Typical equipment & failure modes
Common applications
- steel-plant continuous-caster segments
- large induced-draft fan rotors
- SAG and ball-mill drive shafts
- large mining crusher main shafts
Known failure patterns
- raceway fatigue spalling of the sphered outer raceway after extended service above the catalogue L10 rating
- inner-ring raceway spalling from edge loading when misalignment exceeds the self-aligning recovery range
- stamped-steel cage fatigue after long service in high-vibration screening duty without the VA405 execution
- surface distress and smearing when the relubrication interval is exceeded — the W33 groove is only effective if grease actually reaches the roller rows
- hard-particle indentation of the raceway in unfiltered oil or contaminated grease systems
Selection pitfalls — read before you substitute
- At 260 mm bore the ring mass makes cocking during mounting a real risk; guide the bearing square, confirm seat contact around the full circumference, and re-check the self-aligning swing after the housing cap is torqued down.
- The 24100-series series at 260 mm bore (440×180 mm) is the heaviest medium-OD execution, built for extreme radial and shock loads at low speed; the 950 r/min ceiling is part of the design, not an afterthought — check it before using it in a faster drive.
- The 24152 shares its ISO 15 envelope across brands, but internal geometry differs — SKF load ratings in this row are 3086/4800 kN; another maker's same-size bearing may rate higher or lower, so do not interchange on envelope alone.
- Open spherical roller bearings rely on the housing seals; in screening or crusher duty a failed seal lets grit into the sphered raceway and the 24152 pits long before its L10 life.
- The 3086/4800 kN ratings are SKF catalogue values for this exact execution (24152 CC/W33); SKF can revise internal geometry without changing the order number, so keep the catalogue version (SKF catalogue PUB BU/P1 17000) with the specification and re-verify for critical drives.
- SKF lists several executions of 24152 (cylindrical bore as listed, tapered-bore 24152 CCK30/W33 variant, plus sealed and vibrating-screen options in the same envelope); they are not interchangeable order numbers — quote the full 24152 CC/W33 designation when purchasing.
Frequently asked questions
What are the dimensions and catalogue data of 24152?
The 24152 CC/W33 is a double-row spherical roller bearing with 260 mm bore, 440 mm outer diameter and 180 mm width (10.236 × 17.323 × 7.087 in) per ISO 15. From SKF catalogue PUB BU/P1 17000: basic dynamic load rating C 3086 kN, C0 4800 kN, fatigue load limit Pu 380 kN, reference speed 670 r/min, limiting speed 950 r/min, mass about 110000 g. It is an open, self-aligning bearing with two pressed-steel cages with a floating guide ring.
How does the 24152 bore code work?
The last two digits of 24152 are bore code 52, so 52 × 5 = 260 mm bore. The 440 mm OD and 180 mm width come from the ISO 15 dimension-series plan (dimension series 41 (medium OD, maximum width)), shared with other spherical roller bearings of the same code.
What does the CC/W33 suffix mean on 24152?
CC denotes two pressed-steel cages with a floating guide ring between the roller rows, and W33 adds an annular groove plus three lubrication holes in the outer ring for relubrication. In dimension series 40/41 the tapered-bore counterpart carries CCK30/W33 with a 1:30 taper.
Can 24152 accommodate misalignment and axial load?
Yes on both counts. The sphered outer raceway lets the bearing self-align ≈ 0.5–2.5° depending on series, absorbing shaft deflection and housing-seat errors. The two barrel-roller rows also carry bidirectional axial load in addition to heavy radial load — this is the key difference from cylindrical roller bearings, which take no axial load.
When should the tapered-bore 24152K30 variant be used instead?
Choose the K30 (1:30 tapered bore) variant when the bearing must seat on an adapter or withdrawal sleeve — typical for long shafts, frequent dismounting, or stepped shafts where machining a precision journal is impractical. Sleeve mounting requires measuring clearance reduction or axial drive-up, not nut torque. The cylindrical-bore 24152 listed here seats directly on a machined journal.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 9.1 spherical roller bearings on 2026-09-26. Read our editorial & correction policy.