32213-SKF bearing: complete specifications & equivalents

Specification table

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 8.1 metric single-row TRB) · extracted 2026-09-28

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 8.1 metric single-row TRB); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 32213-SKF model number is decoded

In SKF catalogue PUB BU/P1 17000, 32213 appears as SKF 32213: an open, single-row tapered roller bearing in the heavy section of the 32200 dimension series, supplied with a pressed-steel cage as standard.Numbering ties the bearing to its envelope: 32213 means tapered-roller type 3, heavy section series 22, 65 mm bore — which is why the 120×32.75 mm outline swaps dimensionally with other ISO 355 bearings of the same code. In SKF suffix language a bare 32213 is the standard execution; B marks a larger contact angle and Q or J2 mark clearance/cage variants, all quoted separately. The 22.8 kN Pu figure feeds the adjusted-life equation at contaminated or partial-film conditions, and the 1.04 C0/C balance shows this execution is tuned to thrust-heavy combined loads rather than pure radial running. A single 32213 locates the shaft in one axial direction only; mount it against a second bearing in O (back-to-back) or X (face-to-face) arrangement, and set the running clearance by the mounting procedure — not by feel. Speed envelope and thermal behaviour: at 4,500 r/min thermal reference, the 65 mm bore shaft runs at a dn of 293k, and the 27.5 mm section dissipates heat through the cup-to-housing contact path; the 5,600 r/min mechanical ceiling reflects cage strength, and the 1500 g spinning cone contributes gyroscopic moment under rapid speed reversal.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Mount the 65 mm bore 32213 by induction heating of the cone (max 120 °C — the pressed-steel cage sets the ceiling, not the steel); driving it home through the cup or rollers brinells the tapered raceway.
• The 322 series at 65 mm bore (120×32.75 mm) is a wider, higher-capacity section than 30213; do not substitute without re-checking shaft shoulder diameters and pair setting.
• The tapered contact angle creates an induced axial load under pure radial force; include it in the 32213 rating calculation (and account for it in both bearings of a pair) or the unloaded bearing skids its rollers.
• A single 32213 cannot locate the shaft axially in both directions; mounting it singly on a reversing-thrust shaft leaves one direction uncontrolled — always use an O or X matched pair for bidirectional location.
• Never press both rings through the wrong element during fitting: force for an interference shaft seat goes through the cone only, or brinell marks on the 120 mm cup race release as noise within the first running hours.
• The 186/193 kN ratings are SKF catalogue 17000 values for the basic execution; SKF can revise internal geometry without changing the order number, so keep the catalogue version (PUB BU/P1 17000/1 EN, 2018) with the specification and re-verify for critical drives.
• SKF lists several executions of 32213 (basic, B steeper angle, Q/J2 clearance variants); they are not interchangeable order numbers — quote the full SKF 32213 designation when purchasing and match the execution to the mounting arrangement.