32214-SKF bearing: complete specifications & equivalents

Specification table

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 8.1 metric single-row TRB) · extracted 2026-09-28

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 8.1 metric single-row TRB); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 32214-SKF model number is decoded

SKF 32214 belongs to the SKF single-row tapered roller range — the 70 mm bore entry in the 32200 series, dimensioned 125 mm OD and 33.25 mm wide to the ISO 355 boundary plan.On the SKF nameplate, 32214 follows the ISO 355 convention: 3 for the tapered-roller type, 22 for the heavy section, final digits 14 for the 70 mm bore. In SKF suffix language a bare 32214 is the standard execution; B marks a larger contact angle and Q or J2 mark clearance/cage variants, all quoted separately. Selection arithmetic: the C0/C ratio is about 1.07 (static 208 kN against dynamic 195 kN), typical of a tapered roller sized for axial capacity, and the 24.5 kN fatigue load limit Pu is the equivalent-load floor used in the life calculation. Note the minimum-axial-load requirement: at light radial load and high speed the rollers of 32214 must still be held into the rib contact, which is another reason the catalogue recommends paired mounting with controlled setting. Load system: the 195 kN basic dynamic rating C and 208 kN static rating C0 give a C0/C balance of 1.07, and dividing C by the 70 mm bore yields 2.79 kN per millimetre of journal — a density metric that compares across families; the 24.5 kN fatigue limit Pu is the floor beneath which the adjusted-life calculation drops below acceptable L10 hours for a 70 mm shaft carrying variable duty.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Mount the 70 mm bore 32214 by induction heating of the cone (max 120 °C — the pressed-steel cage sets the ceiling, not the steel); driving it home through the cup or rollers brinells the tapered raceway.
• The 322 series at 70 mm bore (125×33.25 mm) is a wider, higher-capacity section than 30214; do not substitute without re-checking shaft shoulder diameters and pair setting.
• Setting is a design value, not an assembly feel: excessive preload in the 32214 pair raises operating temperature and can trigger thermal runaway, while too little lets the rollers skid and smear the raceway under light load.
• At the 195 kN rating of 32214, preload class changes stiffness by tens of percent but also heat generation; select light preload for the 5,300 r/min speed end and heavier preload only where moment stiffness dominates.
• The pressed-steel cage is rated for standard industrial service; sustained running above the limiting speed or with degraded lubricant wears the cage pockets — inspect the cage at every relubrication interval.
• The 195/208 kN ratings are SKF catalogue 17000 values for the basic execution; SKF can revise internal geometry without changing the order number, so keep the catalogue version (PUB BU/P1 17000/1 EN, 2018) with the specification and re-verify for critical drives.
• SKF lists several executions of 32214 (basic, B steeper angle, Q/J2 clearance variants); they are not interchangeable order numbers — quote the full SKF 32214 designation when purchasing and match the execution to the mounting arrangement.