32319 bearing: complete specifications & equivalents
The 32319 is a ISO 355 radial bearing sized 95 x 200 x 71.5 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 95 mm |
| Outer diameter D | 200 mm |
| Width B | 71.5 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 535 kN |
| Basic static load rating C0 | 670 kN |
| Fatigue load limit Pu | 72 kN |
| Reference speed (thermal) | 2400 rpm |
| Limiting speed (mechanical) | 3400 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 9800 g |
| Manufacturer designation | SKF 32319 |
| Standard | ISO 355 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 8.1 metric single-row TRB |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 8.1 metric single-row TRB) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 8.1 metric single-row TRB); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 32300-series range
| Bore d | 3.74 in |
|---|---|
| Outer diameter D | 7.874 in |
| Width B | 2.815 in |
| ISO bore code | 19 |
| Radial section height (D−d)/2 | 52.5 mm |
| Smallest bore in 32300-series | 20 mm |
| Largest outer diameter in 32300-series | 460 mm |
| Width range across 32300-series | 22.25–154 mm |
| Bore position in 32300-series (smallest first) | 17 of 30 |
| Bore above smallest 32300-series size | 75 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 32319 | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 32319 model number is decoded
SKF 32319 belongs to the SKF single-row tapered roller range — the 95 mm bore entry in the 32300 series, dimensioned 200 mm OD and 71.5 mm wide to the ISO 355 boundary plan.Reading the designation: the leading 3 marks a single-row tapered roller bearing, the 2 is the ISO 355 diameter/width series (extra-heavy section), and the last two digits encode the 95 mm bore; the 200 mm OD and 71.5 mm width follow the ISO 355 general plan. SKF lists the plain number as the basic execution; letter suffixes such as B denote a steeper contact angle and are different order numbers. Selection arithmetic: the C0/C ratio is about 1.25 (static 670 kN against dynamic 535 kN), typical of a tapered roller sized for axial capacity, and the 72 kN fatigue load limit Pu is the equivalent-load floor used in the life calculation. Because the contact line is tapered, one 32319 reacts thrust in a single direction; bidirectional shafts need an O or X pair, and a rotating cone on a 95 mm shaft typically takes a k5 seat with an H7 housing bore.
Typical equipment & failure modes
Common applications
- heavy industrial gearboxes and speed reducers
- large process pump and compressor shafts
- rolling-mill auxiliary drives
- crane sheave and hoist gearboxes
Known failure patterns
- cup or cone misalignment when the separable rings are not seated square during mounting
- loose cup rotation in the housing when the specified press fit is not achieved
- false brinelling on idle paired sets exposed to machine vibration
- roller large-end smearing against the cone rib after EP lubricant film failure
- pressed-steel cage wear or fracture after prolonged running above the limiting speed
- mounting score marks when the cone is cocked over the shaft keyway or a burr
Selection pitfalls — read before you substitute
- Mount the 95 mm bore 32319 by induction heating of the cone (max 120 °C — the pressed-steel cage sets the ceiling, not the steel); driving it home through the cup or rollers brinells the tapered raceway.
- The 323 series at 95 mm bore (200×71.5 mm) is the heavy-duty section of the tapered family; it runs hotter at the same speed than a 30219, so recalculate dn and lubricant film before substitution.
- When the outer ring rotates, reverse the fit logic and provide cup location; the tapered contact of 32319 pushes the rings apart under load, so a non-located cup walks its seat even when the shaft is fixed.
- When the outer ring rotates, reverse the fit logic and provide cup location; the tapered contact of 32319 pushes the rings apart under load, so a non-located cup walks its seat even when the shaft is fixed.
- Never press both rings through the wrong element during fitting: force for an interference shaft seat goes through the cone only, or brinell marks on the 200 mm cup race release as noise within the first running hours.
- The 535/670 kN ratings are SKF catalogue 17000 values for the basic execution; SKF can revise internal geometry without changing the order number, so keep the catalogue version (PUB BU/P1 17000/1 EN, 2018) with the specification and re-verify for critical drives.
- SKF lists several executions of 32319 (basic, B steeper angle, Q/J2 clearance variants); they are not interchangeable order numbers — quote the full SKF 32319 designation when purchasing and match the execution to the mounting arrangement.
Frequently asked questions
What are the dimensions and catalogue data of 32319?
The SKF 32319 is a single-row tapered roller bearing with 95 mm bore, 200 mm outer diameter and 71.5 mm width (3.74 × 7.874 × 2.815 in) per ISO 355. From SKF catalogue PUB BU/P1 17000: basic dynamic load rating C 535 kN, C0 670 kN, fatigue load limit Pu 72 kN, reference speed 2,400 r/min, limiting speed 3,400 r/min, mass about 9800 g. It is an open, separable bearing with a pressed-steel cage.
How does the 32319 bore code work?
The last two digits of 32319 are bore code 19, so 19 × 5 = 95 mm bore. The 200 mm OD and 71.5 mm width come from the ISO 355 dimension-series plan, shared with other tapered bearings of the same code.
What do the 32319 series and basic execution designations mean?
The leading 3 marks a single-row tapered roller bearing; the second digit 2 is the ISO 355 series (extra-heavy section). The SKF catalogue lists the ISO 355 dimension-series code after the bare number. A steeper-contact-angle variant (B suffix) is a different order number and is not interchangeable with the basic execution.
Can a single 32319 take axial load in both directions?
No — one single-row tapered roller bearing reacts thrust in one direction only, and under radial load its contact angle induces an axial force. Use two bearings as a matched pair: O (back-to-back) for a rigid, moment-resisting arrangement, X (face-to-face) where thermal expansion must be tolerated, or tandem where one-direction thrust is shared.
How does 32319 compare with a ball bearing of the same bore?
A tapered roller bearing has line contact and a steep contact angle: much higher combined axial-plus-radial capacity and shock resistance than a ball bearing of the same bore, at the cost of speed, one-direction thrust, mandatory pairing for reversing loads and a minimum axial load requirement. A ball bearing cannot be dropped into a combined-load 32319 position and vice versa — verify load direction, Fa/Fr ratio and speed before substituting.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 8.1 metric single-row TRB on 2026-09-26. Read our editorial & correction policy.