4130-530UTG bearing: complete specifications & equivalents
The 4130-530UTG is a ANSI ABMA 19.2 radial bearing sized 530 x 780 x 185 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 530 mm |
| Outer diameter D | 780 mm |
| Width B | 185 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel |
| Basic dynamic load rating C | 3750 kN |
| Basic static load rating C0 | 5900 kN |
| Fatigue load limit Pu | 410 kN |
| Limiting speed (mechanical) | 290 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 270000 g |
| Manufacturer designation | NTN 4T-4130/530UTG |
| Standard | ANSI ABMA 19.2 |
| Catalog version | NTN 2203E 2026-09-25 |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN 2203E 2026-09-25) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN 2203E 2026-09-25); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 4t-430-series range
| Bore d | 20.866 in |
|---|---|
| Outer diameter D | 30.709 in |
| Width B | 7.283 in |
| ISO bore code | 30 |
| Radial section height (D−d)/2 | 125 mm |
| Smallest bore in 4t-430-series | 40 mm |
| Largest outer diameter in 4t-430-series | 870 mm |
| Width range across 4t-430-series | 45–310 mm |
| Bore position in 4t-430-series (smallest first) | 40 of 41 |
| Bore above smallest 4t-430-series size | 490 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 4130 | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; brand-specific OEM equivalents (NSK/FAG/NTN) pending multi-source data. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 4130-530UTG model number is decoded
For a 530 mm shaft needing a compact two-direction thrust location, NTN lists 4T-4130/530UTG, a TDO double-row 4T unit of 3750 kN C and 5900 kN C0 in the light-duty 430-family TDO double-row series. Unlike a pair of single-row bearings, the TDO unit of 4T-4130/530UTG integrates both rows in one article: the 185 mm overall width and the internal clearance are ground and set by NTN, so there is no field adjustment dimension. Grease relubrication at the 290 r/min limiting speed must reach both roller rows; sustaining 420 r/min needs an oil supply with defined flow through the double cup. The internal clearance of 4T-4130/530UTG is set at the factory by the double cup and spacer-less grinding; do not attempt to re-adjust it with shaft nuts — the 185 mm overall width is the finished dimension. Fillet radii and shoulder heights must follow the 2203E mounting table for 4T-4130/530UTG; the double cup must seat square across its full 185 mm width.
Typical equipment & failure modes
Common applications
- large shredder and recycler main shafts
- power-plant mill and fan shafts
- rolling-mill roll-neck and pinion-stand positions
- mine hoist and dragline drum shafts
Known failure patterns
- edge loading on one row when the housing seats the double cup cocked across its width
- overheated running after a field attempt to "tighten up" the factory-set internal clearance
- one-row flaking when a bent shaft concentrates the combined load on a single row of the pair
- cage fatigue after continuous running near the grease limiting speed without oil cooling
- indentation of both raceways by hard particles in an open, unsealed arrangement
Selection pitfalls — read before you substitute
- At 530 mm bore the 4T-4130/530UTG unit needs hydraulic or crane-assisted fitting and a verified oil supply; manual methods cannot control seating at the 3750 kN C level.
- The 430 light plan keeps 4T-4130/530UTG narrower and faster than the 432 heavy execution of the same 530 mm bore; where shock or a high thrust share dominates, verify whether the heavier 432-family row is the intended position.
- Order by the full 4130/530UTG code including suffixes — U, X, DX, E1 and UTG variants share the 530 mm bore but are different articles with different internal geometry.
- Lubricant must reach both rows: a housing groove aligned to the cup mid-width of 4T-4130/530UTG feeds the two roller complements evenly; a single-side feed starves the far row.
- Open 4T-4130/530UTG units have no seals: the housing must seal both rows or the 290 r/min grease figure is meaningless once contamination enters.
- The 3750/5900 kN ratings and 410 kN Cu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 4T-4130/530UTG; internal geometry legitimately differs between manufacturers, so re-verify ratings, clearance class and suffix before substituting another make on a rated drive.
Frequently asked questions
What are the dimensions and catalogue ratings of NTN 4T-4130/530UTG?
4T-4130/530UTG is a double-row tapered roller bearing of TDO (back-to-back) construction: 530 mm bore, 780 mm outside diameter and 185 mm overall width. From NTN Ball and Roller Bearings CAT.No.2203E: C 3750 kN, C0 5900 kN, Cu 410 kN, grease limiting speed 290 r/min, oil speed 420 r/min, mass about 270 kg. It is an open, preset-clearance unit with pressed-steel cages.
What is the difference between the NTN 430 and 432 double-row series at 530 mm bore?
Both are TDO double-row tapered roller units, but 430 is the light plan and 432 the heavy plan: at the same bore the 432 execution is wider and heavier with higher load ratings. 4T-4130/530UTG belongs to the light-duty 430-family TDO double-row series. Large sizes continue the plans as 4130/4131/4230/4231 (430 family) and 3230/3231 (432 family).
Can the internal clearance of 4T-4130/530UTG be adjusted at mounting?
No. The TDO unit — two cone assemblies against one double cup — is ground and set by NTN at the factory, and the 185 mm overall width is the finished dimension. Mounting sets no end play: seat the unit square, clamp the cup uniformly and verify free rotation. Field re-adjustment overloads one row.
What do the suffix letters on 4130/530UTG mean?
Suffix reading on 4130/530UTG: UTG marks the ULTAGE specification for large NTN tapered rollers — upgraded material and internal design, printed with the ＊ symbol ahead of the order number; suffixed variants are separate order numbers and are not interchangeable articles.
Why does 4T-4130/530UTG list two speeds, 290 and 420 r/min?
The lower figure, 290 r/min, is the grease-lubricated limiting speed for the two rows and their cages. With oil lubrication NTN rates 4T-4130/530UTG at 420 r/min because oil removes heat from both roller rows better — the housing feed must reach both rows through the double cup.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN 2203E 2026-09-25 on 2026-10-01. Read our editorial & correction policy.