413160UTG bearing: complete specifications & equivalents
The 413160UTG is a ANSI ABMA 19.2 radial bearing sized 300 x 500 x 160 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 300 mm |
| Outer diameter D | 500 mm |
| Width B | 160 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel |
| Basic dynamic load rating C | 2580 kN |
| Basic static load rating C0 | 3600 kN |
| Fatigue load limit Pu | 290 kN |
| Limiting speed (mechanical) | 530 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 110000 g |
| Manufacturer designation | NTN 4T-413160UTG |
| Standard | ANSI ABMA 19.2 |
| Catalog version | NTN 2203E 2026-09-25 |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN 2203E 2026-09-25) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN 2203E 2026-09-25); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 4t-430-series range
| Bore d | 11.811 in |
|---|---|
| Outer diameter D | 19.685 in |
| Width B | 6.299 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 100 mm |
| Smallest bore in 4t-430-series | 40 mm |
| Largest outer diameter in 4t-430-series | 870 mm |
| Width range across 4t-430-series | 45–310 mm |
| Bore position in 4t-430-series (smallest first) | 29 of 41 |
| Bore above smallest 4t-430-series size | 260 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 413160UTG | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; brand-specific OEM equivalents (NSK/FAG/NTN) pending multi-source data. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 413160UTG model number is decoded
4T-413160UTG is the NTN 4T catalogue entry for a 300×500×160 mm double-row tapered roller bearing — the TDO arrangement reacts radial load plus thrust in both directions without a second bearing. Unlike a pair of single-row bearings, the TDO unit of 4T-413160UTG integrates both rows in one article: the 160 mm overall width and the internal clearance are ground and set by NTN, so there is no field adjustment dimension. Selection: C 2580 kN against C0 3600 kN gives a C0/C ratio of 1.40; the two rows of 4T-413160UTG share the combined load as one bearing position. The internal clearance of 4T-413160UTG is set at the factory by the double cup and spacer-less grinding; do not attempt to re-adjust it with shaft nuts — the 160 mm overall width is the finished dimension. The open unit carries no seals; the housing of 4T-413160UTG must provide sealing and the grease fill or oil feed to both rows.
Typical equipment & failure modes
Common applications
- heavy press and forging-machine drives
- large shredder and recycler main shafts
- power-plant mill and fan shafts
- rolling-mill roll-neck and pinion-stand positions
Known failure patterns
- edge loading on one row when the housing seats the double cup cocked across its width
- one-row flaking when a bent shaft concentrates the combined load on a single row of the pair
- overheated running after a field attempt to "tighten up" the factory-set internal clearance
- cage fatigue after continuous running near the grease limiting speed without oil cooling
- indentation of both raceways by hard particles in an open, unsealed arrangement
Selection pitfalls — read before you substitute
- At 300 mm bore the 4T-413160UTG unit needs hydraulic or crane-assisted fitting and a verified oil supply; manual methods cannot control seating at the 2580 kN C level.
- The 430 light plan keeps 4T-413160UTG narrower and faster than the 432 heavy execution of the same 300 mm bore; where shock or a high thrust share dominates, verify whether the heavier 432-family row is the intended position.
- Clamping the double cup with a cocked end cover pinches one row: tighten the 500 mm OD clamping uniformly around the circumference.
- An unloaded 4T-413160UTG near 530 r/min lets rollers skid; ensure a minimum load or light spring preload on high-speed positions.
- The 2580 kN C already includes two-row load sharing — do not double it when pairing the unit with a floating bearing in the L10 calculation.
- The 2580/3600 kN ratings and 290 kN Cu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 4T-413160UTG; internal geometry legitimately differs between manufacturers, so re-verify ratings, clearance class and suffix before substituting another make on a rated drive.
Frequently asked questions
What are the dimensions and catalogue ratings of NTN 4T-413160UTG?
4T-413160UTG is a double-row tapered roller bearing of TDO (back-to-back) construction: 300 mm bore, 500 mm outside diameter and 160 mm overall width. From NTN Ball and Roller Bearings CAT.No.2203E: C 2580 kN, C0 3600 kN, Cu 290 kN, grease limiting speed 530 r/min, oil speed 770 r/min, mass about 110 kg. It is an open, preset-clearance unit with pressed-steel cages.
What is the difference between the NTN 430 and 432 double-row series at 300 mm bore?
Both are TDO double-row tapered roller units, but 430 is the light plan and 432 the heavy plan: at the same bore the 432 execution is wider and heavier with higher load ratings. 4T-413160UTG belongs to the light-duty 430-family TDO double-row series. Large sizes continue the plans as 4130/4131/4230/4231 (430 family) and 3230/3231 (432 family).
Can the internal clearance of 4T-413160UTG be adjusted at mounting?
No. The TDO unit — two cone assemblies against one double cup — is ground and set by NTN at the factory, and the 160 mm overall width is the finished dimension. Mounting sets no end play: seat the unit square, clamp the cup uniformly and verify free rotation. Field re-adjustment overloads one row.
What do the suffix letters on 413160UTG mean?
Suffix reading on 413160UTG: UTG marks the ULTAGE specification for large NTN tapered rollers — upgraded material and internal design, printed with the ＊ symbol ahead of the order number; suffixed variants are separate order numbers and are not interchangeable articles.
Why does 4T-413160UTG list two speeds, 530 and 770 r/min?
The lower figure, 530 r/min, is the grease-lubricated limiting speed for the two rows and their cages. With oil lubrication NTN rates 4T-413160UTG at 770 r/min because oil removes heat from both roller rows better — the housing feed must reach both rows through the double cup.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN 2203E 2026-09-25 on 2026-10-01. Read our editorial & correction policy.