413172UTG bearing: complete specifications & equivalents
The 413172UTG is a ANSI ABMA 19.2 radial bearing sized 360 x 600 x 192 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 360 mm |
| Outer diameter D | 600 mm |
| Width B | 192 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel |
| Basic dynamic load rating C | 3500 kN |
| Basic static load rating C0 | 5050 kN |
| Fatigue load limit Pu | 385 kN |
| Limiting speed (mechanical) | 430 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 200000 g |
| Manufacturer designation | NTN 4T-413172UTG |
| Standard | ANSI ABMA 19.2 |
| Catalog version | NTN 2203E 2026-09-25 |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN 2203E 2026-09-25) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN 2203E 2026-09-25); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 4t-430-series range
| Bore d | 14.173 in |
|---|---|
| Outer diameter D | 23.622 in |
| Width B | 7.559 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 120 mm |
| Smallest bore in 4t-430-series | 40 mm |
| Largest outer diameter in 4t-430-series | 870 mm |
| Width range across 4t-430-series | 45–310 mm |
| Bore position in 4t-430-series (smallest first) | 32 of 41 |
| Bore above smallest 4t-430-series size | 320 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 413172UTG | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; brand-specific OEM equivalents (NSK/FAG/NTN) pending multi-source data. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 413172UTG model number is decoded
For a 360 mm shaft needing a compact two-direction thrust location, NTN lists 4T-413172UTG, a TDO double-row 4T unit of 3500 kN C and 5050 kN C0 in the light-duty 430-family TDO double-row series. The 4T- prefix is NTN's tapered roller quality mark; 430 numbers the light TDO plan and 432 the heavy TDO plan — at the same 360 mm bore the 432 execution carries a wider, heavier section than the 430. The 120.0 mm radial section over the 360 mm bore carries two roller rows across the 192 mm width; abutment shoulders must clear both cone bores and the double-cup OD. Because the unit is preset, mounting 4T-413172UTG resembles mounting a double-row spherical or cylindrical bearing: seat the unit, clamp axially to the stated end cover torque, and verify rotation — no end-play measurement is required. Re-lubrication holes and grooves of the housing should line up with the cup's mid-width so fresh grease reaches both roller rows of 4T-413172UTG.
Typical equipment & failure modes
Common applications
- heavy press and forging-machine drives
- large shredder and recycler main shafts
- power-plant mill and fan shafts
- rolling-mill roll-neck and pinion-stand positions
Known failure patterns
- roller large-end smearing against the cone ribs when one row of the unit runs starved of lubricant
- brinelling of both rows from a mounting blow transmitted through the roller complements
- preload loss and hammering noise when the cup clamping loosens and the unit gains axial float
- pressed-steel cage pocket wear from roller skid at light load and high speed
- thermal distress when the oil supply sized for one row starves the second row
Selection pitfalls — read before you substitute
- At 360 mm bore the 4T-413172UTG unit needs hydraulic or crane-assisted fitting and a verified oil supply; manual methods cannot control seating at the 3500 kN C level.
- The 430 light plan keeps 4T-413172UTG narrower and faster than the 432 heavy execution of the same 360 mm bore; where shock or a high thrust share dominates, verify whether the heavier 432-family row is the intended position.
- Never interchange a TDO double-row unit with two single-row bearings of similar size: the 192 mm width, load spread and clearance logic of 4T-413172UTG are unit-specific.
- Never interchange a TDO double-row unit with two single-row bearings of similar size: the 192 mm width, load spread and clearance logic of 4T-413172UTG are unit-specific.
- Open 4T-413172UTG units have no seals: the housing must seal both rows or the 430 r/min grease figure is meaningless once contamination enters.
- The 3500/5050 kN ratings and 385 kN Cu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 4T-413172UTG; internal geometry legitimately differs between manufacturers, so re-verify ratings, clearance class and suffix before substituting another make on a rated drive.
Frequently asked questions
What are the dimensions and catalogue ratings of NTN 4T-413172UTG?
4T-413172UTG is a double-row tapered roller bearing of TDO (back-to-back) construction: 360 mm bore, 600 mm outside diameter and 192 mm overall width. From NTN Ball and Roller Bearings CAT.No.2203E: C 3500 kN, C0 5050 kN, Cu 385 kN, grease limiting speed 430 r/min, oil speed 620 r/min, mass about 200 kg. It is an open, preset-clearance unit with pressed-steel cages.
What is the difference between the NTN 430 and 432 double-row series at 360 mm bore?
Both are TDO double-row tapered roller units, but 430 is the light plan and 432 the heavy plan: at the same bore the 432 execution is wider and heavier with higher load ratings. 4T-413172UTG belongs to the light-duty 430-family TDO double-row series. Large sizes continue the plans as 4130/4131/4230/4231 (430 family) and 3230/3231 (432 family).
Can the internal clearance of 4T-413172UTG be adjusted at mounting?
No. The TDO unit — two cone assemblies against one double cup — is ground and set by NTN at the factory, and the 192 mm overall width is the finished dimension. Mounting sets no end play: seat the unit square, clamp the cup uniformly and verify free rotation. Field re-adjustment overloads one row.
What do the suffix letters on 413172UTG mean?
Suffix reading on 413172UTG: UTG marks the ULTAGE specification for large NTN tapered rollers — upgraded material and internal design, printed with the ＊ symbol ahead of the order number; suffixed variants are separate order numbers and are not interchangeable articles.
Why does 4T-413172UTG list two speeds, 430 and 620 r/min?
The lower figure, 430 r/min, is the grease-lubricated limiting speed for the two rows and their cages. With oil lubrication NTN rates 4T-413172UTG at 620 r/min because oil removes heat from both roller rows better — the housing feed must reach both rows through the double cup.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN 2203E 2026-09-25 on 2026-10-01. Read our editorial & correction policy.