423044UTG bearing: complete specifications & equivalents
The 423044UTG is a ANSI ABMA 19.2 radial bearing sized 220 x 340 x 113 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 220 mm |
| Outer diameter D | 340 mm |
| Width B | 113 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel |
| Basic dynamic load rating C | 1130 kN |
| Basic static load rating C0 | 1650 kN |
| Fatigue load limit Pu | 148 kN |
| Limiting speed (mechanical) | 810 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 33000 g |
| Manufacturer designation | NTN 4T-423044UTG |
| Standard | ANSI ABMA 19.2 |
| Catalog version | NTN 2203E 2026-09-25 |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN 2203E 2026-09-25) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN 2203E 2026-09-25); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 4t-430-series range
| Bore d | 8.661 in |
|---|---|
| Outer diameter D | 13.386 in |
| Width B | 4.449 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 60 mm |
| Smallest bore in 4t-430-series | 40 mm |
| Largest outer diameter in 4t-430-series | 870 mm |
| Width range across 4t-430-series | 45–310 mm |
| Bore position in 4t-430-series (smallest first) | 25 of 41 |
| Bore above smallest 4t-430-series size | 180 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 423044UTG | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; brand-specific OEM equivalents (NSK/FAG/NTN) pending multi-source data. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 423044UTG model number is decoded
The NTN 2203E double-row table prints 4T-423044UTG at 220 mm bore, 340 mm OD and 113 mm overall width, with a grease limiting speed of 810 r/min and an oil ceiling of 1,200 r/min. Suffix reading on 423044UTG: UTG marks the ULTAGE specification for large NTN tapered rollers — upgraded material and internal design, printed with the ＊ symbol ahead of the order number; suffixed variants are separate order numbers and are not interchangeable articles. The fatigue load limit Cu printed for 4T-423044UTG is 148 kN — the equivalent-load floor below which high reliability is expected even under contamination in the adjusted-life equation. Because the unit is preset, mounting 4T-423044UTG resembles mounting a double-row spherical or cylindrical bearing: seat the unit, clamp axially to the stated end cover torque, and verify rotation — no end-play measurement is required. Induction heating to max 120 °C is the standard fitting method at this 220 mm bore; driving the unit home through the rollers brinells both rows at once.
Typical equipment & failure modes
Common applications
- mine hoist and dragline drum shafts
- cement-plant mill and kiln drive trains
- port-crane hoist and luffing gearboxes
- heavy press and forging-machine drives
Known failure patterns
- edge loading on one row when the housing seats the double cup cocked across its width
- one-row flaking when a bent shaft concentrates the combined load on a single row of the pair
- overheated running after a field attempt to "tighten up" the factory-set internal clearance
- pressed-steel cage pocket wear from roller skid at light load and high speed
- thermal distress when the oil supply sized for one row starves the second row
Selection pitfalls — read before you substitute
- At 220 mm bore the 4T-423044UTG unit needs hydraulic or crane-assisted fitting and a verified oil supply; manual methods cannot control seating at the 1130 kN C level.
- The 430 light plan keeps 4T-423044UTG narrower and faster than the 432 heavy execution of the same 220 mm bore; where shock or a high thrust share dominates, verify whether the heavier 432-family row is the intended position.
- The internal clearance of 4T-423044UTG is factory-set: no end-play adjustment exists at mounting, and any attempt to set preload with a shaft nut overloads one row.
- Order by the full 423044UTG code including suffixes — U, X, DX, E1 and UTG variants share the 220 mm bore but are different articles with different internal geometry.
- Grease packs must leave free volume across the 113 mm width; over-greasing a unit churning near the 1,200 r/min oil-band speed raises temperature and expels the grease.
- The 1130/1650 kN ratings and 148 kN Cu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 4T-423044UTG; internal geometry legitimately differs between manufacturers, so re-verify ratings, clearance class and suffix before substituting another make on a rated drive.
Frequently asked questions
What are the dimensions and catalogue ratings of NTN 4T-423044UTG?
4T-423044UTG is a double-row tapered roller bearing of TDO (back-to-back) construction: 220 mm bore, 340 mm outside diameter and 113 mm overall width. From NTN Ball and Roller Bearings CAT.No.2203E: C 1130 kN, C0 1650 kN, Cu 148 kN, grease limiting speed 810 r/min, oil speed 1,200 r/min, mass about 33 kg. It is an open, preset-clearance unit with pressed-steel cages.
What is the difference between the NTN 430 and 432 double-row series at 220 mm bore?
Both are TDO double-row tapered roller units, but 430 is the light plan and 432 the heavy plan: at the same bore the 432 execution is wider and heavier with higher load ratings. 4T-423044UTG belongs to the light-duty 430-family TDO double-row series. Large sizes continue the plans as 4130/4131/4230/4231 (430 family) and 3230/3231 (432 family).
Can the internal clearance of 4T-423044UTG be adjusted at mounting?
No. The TDO unit — two cone assemblies against one double cup — is ground and set by NTN at the factory, and the 113 mm overall width is the finished dimension. Mounting sets no end play: seat the unit square, clamp the cup uniformly and verify free rotation. Field re-adjustment overloads one row.
What do the suffix letters on 423044UTG mean?
Suffix reading on 423044UTG: UTG marks the ULTAGE specification for large NTN tapered rollers — upgraded material and internal design, printed with the ＊ symbol ahead of the order number; suffixed variants are separate order numbers and are not interchangeable articles.
Why does 4T-423044UTG list two speeds, 810 and 1,200 r/min?
The lower figure, 810 r/min, is the grease-lubricated limiting speed for the two rows and their cages. With oil lubrication NTN rates 4T-423044UTG at 1,200 r/min because oil removes heat from both roller rows better — the housing feed must reach both rows through the double cup.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN 2203E 2026-09-25 on 2026-10-01. Read our editorial & correction policy.