423126 bearing: complete specifications & equivalents
The 423126 is a ANSI ABMA 19.2 radial bearing sized 130 x 210 x 80 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 130 mm |
| Outer diameter D | 210 mm |
| Width B | 80 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel |
| Basic dynamic load rating C | 455 kN |
| Basic static load rating C0 | 675 kN |
| Fatigue load limit Pu | 70.5 kN |
| Limiting speed (mechanical) | 1400 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 9400 g |
| Manufacturer designation | NTN 4T-423126 |
| Standard | ANSI ABMA 19.2 |
| Catalog version | NTN 2203E 2026-09-25 |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN 2203E 2026-09-25) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN 2203E 2026-09-25); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 4t-430-series range
| Bore d | 5.118 in |
|---|---|
| Outer diameter D | 8.268 in |
| Width B | 3.15 in |
| ISO bore code | 26 |
| Radial section height (D−d)/2 | 40 mm |
| Smallest bore in 4t-430-series | 40 mm |
| Largest outer diameter in 4t-430-series | 870 mm |
| Width range across 4t-430-series | 45–310 mm |
| Bore position in 4t-430-series (smallest first) | 17 of 41 |
| Bore above smallest 4t-430-series size | 90 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 423126 | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; brand-specific OEM equivalents (NSK/FAG/NTN) pending multi-source data. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 423126 model number is decoded
For a 130 mm shaft needing a compact two-direction thrust location, NTN lists 4T-423126, a TDO double-row 4T unit of 455 kN C and 675 kN C0 in the light-duty 430-family TDO double-row series. With no letter suffix, 423126 is the basic open double-row execution: steel cages, factory-set internal clearance, no feature suffix in the order code. The 3.5 kN of dynamic capacity per millimetre of bore summarises the 455 kN rating over the 130 mm bore — compare substitution candidates on this ratio and on the 80 mm width. TDO construction means the two cone assemblies of 4T-423126 face away from each other inside one double cup: the load lines diverge outward, giving a wide effective spread and high moment stiffness for the 130 mm shaft. Do not separate the cones from the double cup at inspection unless re-matching is guaranteed — the rows of 4T-423126 are ground as a unit.
Typical equipment & failure modes
Common applications
- mine hoist and dragline drum shafts
- cement-plant mill and kiln drive trains
- port-crane hoist and luffing gearboxes
- heavy press and forging-machine drives
Known failure patterns
- edge loading on one row when the housing seats the double cup cocked across its width
- brinelling of both rows from a mounting blow transmitted through the roller complements
- preload loss and hammering noise when the cup clamping loosens and the unit gains axial float
- cage fatigue after continuous running near the grease limiting speed without oil cooling
- false brinelling on a stored or standby unit exposed to vibration
Selection pitfalls — read before you substitute
- At 130 mm bore the 4T-423126 unit needs hydraulic or crane-assisted fitting and a verified oil supply; manual methods cannot control seating at the 455 kN C level.
- The 430 light plan keeps 4T-423126 narrower and faster than the 432 heavy execution of the same 130 mm bore; where shock or a high thrust share dominates, verify whether the heavier 432-family row is the intended position.
- Never interchange a TDO double-row unit with two single-row bearings of similar size: the 80 mm width, load spread and clearance logic of 4T-423126 are unit-specific.
- Lubricant must reach both rows: a housing groove aligned to the cup mid-width of 4T-423126 feeds the two roller complements evenly; a single-side feed starves the far row.
- The internal clearance of 4T-423126 is factory-set: no end-play adjustment exists at mounting, and any attempt to set preload with a shaft nut overloads one row.
- The 455/675 kN ratings and 70.5 kN Cu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 4T-423126; internal geometry legitimately differs between manufacturers, so re-verify ratings, clearance class and suffix before substituting another make on a rated drive.
Frequently asked questions
What are the dimensions and catalogue ratings of NTN 4T-423126?
4T-423126 is a double-row tapered roller bearing of TDO (back-to-back) construction: 130 mm bore, 210 mm outside diameter and 80 mm overall width. From NTN Ball and Roller Bearings CAT.No.2203E: C 455 kN, C0 675 kN, Cu 70.5 kN, grease limiting speed 1,400 r/min, oil speed 1,800 r/min, mass about 9.4 kg. It is an open, preset-clearance unit with pressed-steel cages.
What is the difference between the NTN 430 and 432 double-row series at 130 mm bore?
Both are TDO double-row tapered roller units, but 430 is the light plan and 432 the heavy plan: at the same bore the 432 execution is wider and heavier with higher load ratings. 4T-423126 belongs to the light-duty 430-family TDO double-row series. Large sizes continue the plans as 4130/4131/4230/4231 (430 family) and 3230/3231 (432 family).
Can the internal clearance of 4T-423126 be adjusted at mounting?
No. The TDO unit — two cone assemblies against one double cup — is ground and set by NTN at the factory, and the 80 mm overall width is the finished dimension. Mounting sets no end play: seat the unit square, clamp the cup uniformly and verify free rotation. Field re-adjustment overloads one row.
What do the suffix letters on 423126 mean?
With no letter suffix, 423126 is the basic open double-row execution: steel cages, factory-set internal clearance, no feature suffix in the order code.
Why does 4T-423126 list two speeds, 1,400 and 1,800 r/min?
The lower figure, 1,400 r/min, is the grease-lubricated limiting speed for the two rows and their cages. With oil lubrication NTN rates 4T-423126 at 1,800 r/min because oil removes heat from both roller rows better — the housing feed must reach both rows through the double cup.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN 2203E 2026-09-25 on 2026-10-01. Read our editorial & correction policy.