423140UTG bearing: complete specifications & equivalents
The 423140UTG is a ANSI ABMA 19.2 radial bearing sized 200 x 340 x 140 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 200 mm |
| Outer diameter D | 340 mm |
| Width B | 140 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel |
| Basic dynamic load rating C | 1400 kN |
| Basic static load rating C0 | 1910 kN |
| Fatigue load limit Pu | 173 kN |
| Limiting speed (mechanical) | 840 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 47300 g |
| Manufacturer designation | NTN 4T-423140UTG |
| Standard | ANSI ABMA 19.2 |
| Catalog version | NTN 2203E 2026-09-25 |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN 2203E 2026-09-25) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN 2203E 2026-09-25); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 4t-430-series range
| Bore d | 7.874 in |
|---|---|
| Outer diameter D | 13.386 in |
| Width B | 5.512 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 70 mm |
| Smallest bore in 4t-430-series | 40 mm |
| Largest outer diameter in 4t-430-series | 870 mm |
| Width range across 4t-430-series | 45–310 mm |
| Bore position in 4t-430-series (smallest first) | 24 of 41 |
| Bore above smallest 4t-430-series size | 160 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 423140UTG | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; brand-specific OEM equivalents (NSK/FAG/NTN) pending multi-source data. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 423140UTG model number is decoded
4T-423140UTG is the NTN 4T catalogue entry for a 200×340×140 mm double-row tapered roller bearing — the TDO arrangement reacts radial load plus thrust in both directions without a second bearing. Unlike a pair of single-row bearings, the TDO unit of 4T-423140UTG integrates both rows in one article: the 140 mm overall width and the internal clearance are ground and set by NTN, so there is no field adjustment dimension. The fatigue load limit Cu printed for 4T-423140UTG is 173 kN — the equivalent-load floor below which high reliability is expected even under contamination in the adjusted-life equation. TDO construction means the two cone assemblies of 4T-423140UTG face away from each other inside one double cup: the load lines diverge outward, giving a wide effective spread and high moment stiffness for the 200 mm shaft. Re-lubrication holes and grooves of the housing should line up with the cup's mid-width so fresh grease reaches both roller rows of 4T-423140UTG.
Typical equipment & failure modes
Common applications
- rolling-mill roll-neck and pinion-stand positions
- mine hoist and dragline drum shafts
- cement-plant mill and kiln drive trains
- port-crane hoist and luffing gearboxes
Known failure patterns
- roller large-end smearing against the cone ribs when one row of the unit runs starved of lubricant
- brinelling of both rows from a mounting blow transmitted through the roller complements
- preload loss and hammering noise when the cup clamping loosens and the unit gains axial float
- cage damage when the unit is lifted by one cone instead of the double cup during fitting
- water-induced pitting when washdown reaches the open unit without external seals
Selection pitfalls — read before you substitute
- At 200 mm bore the 4T-423140UTG unit needs hydraulic or crane-assisted fitting and a verified oil supply; manual methods cannot control seating at the 1400 kN C level.
- The 430 light plan keeps 4T-423140UTG narrower and faster than the 432 heavy execution of the same 200 mm bore; where shock or a high thrust share dominates, verify whether the heavier 432-family row is the intended position.
- Never interchange a TDO double-row unit with two single-row bearings of similar size: the 140 mm width, load spread and clearance logic of 4T-423140UTG are unit-specific.
- Lubricant must reach both rows: a housing groove aligned to the cup mid-width of 4T-423140UTG feeds the two roller complements evenly; a single-side feed starves the far row.
- An unloaded 4T-423140UTG near 840 r/min lets rollers skid; ensure a minimum load or light spring preload on high-speed positions.
- The 1400/1910 kN ratings and 173 kN Cu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 4T-423140UTG; internal geometry legitimately differs between manufacturers, so re-verify ratings, clearance class and suffix before substituting another make on a rated drive.
Frequently asked questions
What are the dimensions and catalogue ratings of NTN 4T-423140UTG?
4T-423140UTG is a double-row tapered roller bearing of TDO (back-to-back) construction: 200 mm bore, 340 mm outside diameter and 140 mm overall width. From NTN Ball and Roller Bearings CAT.No.2203E: C 1400 kN, C0 1910 kN, Cu 173 kN, grease limiting speed 840 r/min, oil speed 1,200 r/min, mass about 47.3 kg. It is an open, preset-clearance unit with pressed-steel cages.
What is the difference between the NTN 430 and 432 double-row series at 200 mm bore?
Both are TDO double-row tapered roller units, but 430 is the light plan and 432 the heavy plan: at the same bore the 432 execution is wider and heavier with higher load ratings. 4T-423140UTG belongs to the light-duty 430-family TDO double-row series. Large sizes continue the plans as 4130/4131/4230/4231 (430 family) and 3230/3231 (432 family).
Can the internal clearance of 4T-423140UTG be adjusted at mounting?
No. The TDO unit — two cone assemblies against one double cup — is ground and set by NTN at the factory, and the 140 mm overall width is the finished dimension. Mounting sets no end play: seat the unit square, clamp the cup uniformly and verify free rotation. Field re-adjustment overloads one row.
What do the suffix letters on 423140UTG mean?
Suffix reading on 423140UTG: UTG marks the ULTAGE specification for large NTN tapered rollers — upgraded material and internal design, printed with the ＊ symbol ahead of the order number; suffixed variants are separate order numbers and are not interchangeable articles.
Why does 4T-423140UTG list two speeds, 840 and 1,200 r/min?
The lower figure, 840 r/min, is the grease-lubricated limiting speed for the two rows and their cages. With oil lubrication NTN rates 4T-423140UTG at 1,200 r/min because oil removes heat from both roller rows better — the housing feed must reach both rows through the double cup.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN 2203E 2026-09-25 on 2026-10-01. Read our editorial & correction policy.