430316DU bearing: complete specifications & equivalents
The 430316DU is a ANSI ABMA 19.2 radial bearing sized 80 x 170 x 92 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 80 mm |
| Outer diameter D | 170 mm |
| Width B | 92 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel |
| Basic dynamic load rating C | 450 kN |
| Basic static load rating C0 | 565 kN |
| Fatigue load limit Pu | 64.5 kN |
| Limiting speed (mechanical) | 1600 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 8990 g |
| Manufacturer designation | NTN 4T-430316DU |
| Standard | ANSI ABMA 19.2 |
| Catalog version | NTN 2203E 2026-09-25 |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN 2203E 2026-09-25) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN 2203E 2026-09-25); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 4t-430-series range
| Bore d | 3.15 in |
|---|---|
| Outer diameter D | 6.693 in |
| Width B | 3.622 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 45 mm |
| Smallest bore in 4t-430-series | 40 mm |
| Largest outer diameter in 4t-430-series | 870 mm |
| Width range across 4t-430-series | 45–310 mm |
| Bore position in 4t-430-series (smallest first) | 9 of 41 |
| Bore above smallest 4t-430-series size | 40 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 430316DU | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; brand-specific OEM equivalents (NSK/FAG/NTN) pending multi-source data. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 430316DU model number is decoded
4T-430316DU is the NTN 4T catalogue entry for a 80×170×92 mm double-row tapered roller bearing — the TDO arrangement reacts radial load plus thrust in both directions without a second bearing. Large sizes continue the plans under different leading digits: 4130/4131 and 4230/4231 belong to the 430-family dimension plan, while 3230/3231 continue the 432 heavy plan — 430316DU reads accordingly. Catalogue mass of 4T-430316DU is 8.99 kg; lifting and fitting tackle must be rated for the whole preset unit, not for single-ring handling. Because the unit is preset, mounting 4T-430316DU resembles mounting a double-row spherical or cylindrical bearing: seat the unit, clamp axially to the stated end cover torque, and verify rotation — no end-play measurement is required. With a rotating shaft a k5/m5 seat on the 80 mm journal and a located cup in the housing are typical practice for 4T-430316DU.
Typical equipment & failure modes
Common applications
- crusher and screening-plant main shafts
- large fan and blower shafts with thrust reversal
- steel-plant roller table and conveyor drives
- marine winch and deck-machinery shafts
Known failure patterns
- roller large-end smearing against the cone ribs when one row of the unit runs starved of lubricant
- overheated running after a field attempt to "tighten up" the factory-set internal clearance
- one-row flaking when a bent shaft concentrates the combined load on a single row of the pair
- cage fatigue after continuous running near the grease limiting speed without oil cooling
- rolling-contact fatigue spalling after the catalogue L10 life at the actual combined load
Selection pitfalls — read before you substitute
- Mount the 80 mm unit by induction heating (max 120 °C); at 8.99 kg a cocked lift damages the cages and ribs before the bearing ever runs.
- The 430 light plan keeps 4T-430316DU narrower and faster than the 432 heavy execution of the same 80 mm bore; where shock or a high thrust share dominates, verify whether the heavier 432-family row is the intended position.
- Never interchange a TDO double-row unit with two single-row bearings of similar size: the 92 mm width, load spread and clearance logic of 4T-430316DU are unit-specific.
- The internal clearance of 4T-430316DU is factory-set: no end-play adjustment exists at mounting, and any attempt to set preload with a shaft nut overloads one row.
- Order by the full 430316DU code including suffixes — U, X, DX, E1 and UTG variants share the 80 mm bore but are different articles with different internal geometry.
- The 450/565 kN ratings and 64.5 kN Cu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 4T-430316DU; internal geometry legitimately differs between manufacturers, so re-verify ratings, clearance class and suffix before substituting another make on a rated drive.
Frequently asked questions
What are the dimensions and catalogue ratings of NTN 4T-430316DU?
4T-430316DU is a double-row tapered roller bearing of TDO (back-to-back) construction: 80 mm bore, 170 mm outside diameter and 92 mm overall width. From NTN Ball and Roller Bearings CAT.No.2203E: C 450 kN, C0 565 kN, Cu 64.5 kN, grease limiting speed 1,600 r/min, oil speed 2,200 r/min, mass about 8.99 kg. It is an open, preset-clearance unit with pressed-steel cages.
What is the difference between the NTN 430 and 432 double-row series at 80 mm bore?
Both are TDO double-row tapered roller units, but 430 is the light plan and 432 the heavy plan: at the same bore the 432 execution is wider and heavier with higher load ratings. 4T-430316DU belongs to the light-duty 430-family TDO double-row series. Large sizes continue the plans as 4130/4131/4230/4231 (430 family) and 3230/3231 (432 family).
Can the internal clearance of 4T-430316DU be adjusted at mounting?
No. The TDO unit — two cone assemblies against one double cup — is ground and set by NTN at the factory, and the 92 mm overall width is the finished dimension. Mounting sets no end play: seat the unit square, clamp the cup uniformly and verify free rotation. Field re-adjustment overloads one row.
What do the suffix letters on 430316DU mean?
Suffix reading on 430316DU: U marks the uprated/reinforced internal design, a separate order number with higher capacity than the basic execution; D is an internal-design revision letter of the base number; suffixed variants are separate order numbers and are not interchangeable articles.
Why does 4T-430316DU list two speeds, 1,600 and 2,200 r/min?
The lower figure, 1,600 r/min, is the grease-lubricated limiting speed for the two rows and their cages. With oil lubrication NTN rates 4T-430316DU at 2,200 r/min because oil removes heat from both roller rows better — the housing feed must reach both rows through the double cup.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN 2203E 2026-09-25 on 2026-10-01. Read our editorial & correction policy.