432208X bearing: complete specifications & equivalents
The 432208X is a ANSI ABMA 19.2 radial bearing sized 40 x 80 x 55 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 40 mm |
| Outer diameter D | 80 mm |
| Width B | 55 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel |
| Basic dynamic load rating C | 151 kN |
| Basic static load rating C0 | 187 kN |
| Limiting speed (mechanical) | 4100 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 1180 g |
| Manufacturer designation | NTN 4T-432208X |
| Standard | ANSI ABMA 19.2 |
| Catalog version | NTN 2203E 2026-09-25 |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN 2203E 2026-09-25) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN 2203E 2026-09-25); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 4t-432-series range
| Bore d | 1.575 in |
|---|---|
| Outer diameter D | 3.15 in |
| Width B | 2.165 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 20 mm |
| Smallest bore in 4t-432-series | 40 mm |
| Largest outer diameter in 4t-432-series | 790 mm |
| Width range across 4t-432-series | 46–266 mm |
| Bore position in 4t-432-series (smallest first) | 1 of 39 |
| Bore above smallest 4t-432-series size | 0 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 432208X | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; brand-specific OEM equivalents (NSK/FAG/NTN) pending multi-source data. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 432208X model number is decoded
NTN supplies this 40 mm shaft position as 4T-432208X: a factory-adjusted double-row tapered roller bearing whose two roller rows share one double cup, overall width 55 mm. Reading the designation: the last two digits 08 are the bore code, ×5 = 40 mm (codes 00–03 use the 10/12/15/17 exception table); the leading digits place the bearing in the heavy-duty 432-family TDO double-row series. Catalogue mass of 4T-432208X is 1.18 kg; lifting and fitting tackle must be rated for the whole preset unit, not for single-ring handling. Because the unit is preset, mounting 4T-432208X resembles mounting a double-row spherical or cylindrical bearing: seat the unit, clamp axially to the stated end cover torque, and verify rotation — no end-play measurement is required. Fillet radii and shoulder heights must follow the 2203E mounting table for 4T-432208X; the double cup must seat square across its full 55 mm width.
Typical equipment & failure modes
Common applications
- construction-equipment swing and pivot shafts
- industrial gearbox shafts in a single locating position
- rolling-mill work-roll and backup auxiliary positions
- crane travel and hoist drum shafts
Known failure patterns
- roller large-end smearing against the cone ribs when one row of the unit runs starved of lubricant
- one-row flaking when a bent shaft concentrates the combined load on a single row of the pair
- overheated running after a field attempt to "tighten up" the factory-set internal clearance
- cage damage when the unit is lifted by one cone instead of the double cup during fitting
- rolling-contact fatigue spalling after the catalogue L10 life at the actual combined load
Selection pitfalls — read before you substitute
- Gearbox positions of this 40 mm class rely on the preset clearance of 4T-432208X; shimming or nut-tightening the unit like a single-row pair overruns the factory setting and runs the rows hot.
- The 432 heavy plan gives 4T-432208X its 55 mm width and 151 kN rating at the 40 mm bore; do not downgrade to a 430-family unit of the same bore without re-checking C, C0.
- An unloaded 4T-432208X near 4,100 r/min lets rollers skid; ensure a minimum load or light spring preload on high-speed positions.
- Grease packs must leave free volume across the 55 mm width; over-greasing a unit churning near the 5,500 r/min oil-band speed raises temperature and expels the grease.
- Grease packs must leave free volume across the 55 mm width; over-greasing a unit churning near the 5,500 r/min oil-band speed raises temperature and expels the grease.
- The 151/187 kN ratings here are NTN Ball and Roller Bearings CAT.No.2203E figures for 4T-432208X; internal geometry legitimately differs between manufacturers, so re-verify ratings, clearance class and suffix before substituting another make on a rated drive.
Frequently asked questions
What are the dimensions and catalogue ratings of NTN 4T-432208X?
4T-432208X is a double-row tapered roller bearing of TDO (back-to-back) construction: 40 mm bore, 80 mm outside diameter and 55 mm overall width. From NTN Ball and Roller Bearings CAT.No.2203E: C 151 kN, C0 187 kN (2203E prints a dash for Cu on this size), grease limiting speed 4,100 r/min, oil speed 5,500 r/min, mass about 1.18 kg. It is an open, preset-clearance unit with pressed-steel cages.
What is the difference between the NTN 430 and 432 double-row series at 40 mm bore?
Both are TDO double-row tapered roller units, but 430 is the light plan and 432 the heavy plan: at the same bore the 432 execution is wider and heavier with higher load ratings. 4T-432208X belongs to the heavy-duty 432-family TDO double-row series. Large sizes continue the plans as 4130/4131/4230/4231 (430 family) and 3230/3231 (432 family).
Can the internal clearance of 4T-432208X be adjusted at mounting?
No. The TDO unit — two cone assemblies against one double cup — is ground and set by NTN at the factory, and the 55 mm overall width is the finished dimension. Mounting sets no end play: seat the unit square, clamp the cup uniformly and verify free rotation. Field re-adjustment overloads one row.
What do the suffix letters on 432208X mean?
Suffix reading on 432208X: X marks the boundary-dimension revision of the base number (D and width differ from the plain number of the same bore); suffixed variants are separate order numbers and are not interchangeable articles.
Why does 4T-432208X list two speeds, 4,100 and 5,500 r/min?
The lower figure, 4,100 r/min, is the grease-lubricated limiting speed for the two rows and their cages. With oil lubrication NTN rates 4T-432208X at 5,500 r/min because oil removes heat from both roller rows better — the housing feed must reach both rows through the double cup.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN 2203E 2026-09-25 on 2026-10-01. Read our editorial & correction policy.