432212U bearing: complete specifications & equivalents
The 432212U is a ANSI ABMA 19.2 radial bearing sized 60 x 110 x 66 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 60 mm |
| Outer diameter D | 110 mm |
| Width B | 66 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel |
| Basic dynamic load rating C | 247 kN |
| Basic static load rating C0 | 330 kN |
| Fatigue load limit Pu | 40 kN |
| Limiting speed (mechanical) | 2800 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 2490 g |
| Manufacturer designation | NTN 4T-432212U |
| Standard | ANSI ABMA 19.2 |
| Catalog version | NTN 2203E 2026-09-25 |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN 2203E 2026-09-25) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN 2203E 2026-09-25); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 4t-432-series range
| Bore d | 2.362 in |
|---|---|
| Outer diameter D | 4.331 in |
| Width B | 2.598 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 25 mm |
| Smallest bore in 4t-432-series | 40 mm |
| Largest outer diameter in 4t-432-series | 790 mm |
| Width range across 4t-432-series | 46–266 mm |
| Bore position in 4t-432-series (smallest first) | 5 of 39 |
| Bore above smallest 4t-432-series size | 20 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 432212U | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; brand-specific OEM equivalents (NSK/FAG/NTN) pending multi-source data. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 432212U model number is decoded
The NTN 2203E double-row table prints 4T-432212U at 60 mm bore, 110 mm OD and 66 mm overall width, with a grease limiting speed of 2,800 r/min and an oil ceiling of 3,800 r/min. The 4T- prefix is NTN's tapered roller quality mark; 430 numbers the light TDO plan and 432 the heavy TDO plan — at the same 60 mm bore the 432 execution carries a wider, heavier section than the 430. Grease relubrication at the 2,800 r/min limiting speed must reach both roller rows; sustaining 3,800 r/min needs an oil supply with defined flow through the double cup. TDO construction means the two cone assemblies of 4T-432212U face away from each other inside one double cup: the load lines diverge outward, giving a wide effective spread and high moment stiffness for the 60 mm shaft. Re-lubrication holes and grooves of the housing should line up with the cup's mid-width so fresh grease reaches both roller rows of 4T-432212U.
Typical equipment & failure modes
Common applications
- large mixer and agitator shafts
- heavy gearbox and mill drive shafts
- crusher and screening-plant main shafts
- large fan and blower shafts with thrust reversal
Known failure patterns
- roller large-end smearing against the cone ribs when one row of the unit runs starved of lubricant
- one-row flaking when a bent shaft concentrates the combined load on a single row of the pair
- overheated running after a field attempt to "tighten up" the factory-set internal clearance
- cage fatigue after continuous running near the grease limiting speed without oil cooling
- water-induced pitting when washdown reaches the open unit without external seals
Selection pitfalls — read before you substitute
- Mount the 60 mm unit by induction heating (max 120 °C); at 2.49 kg a cocked lift damages the cages and ribs before the bearing ever runs.
- The 432 heavy plan gives 4T-432212U its 66 mm width and 247 kN rating at the 60 mm bore; do not downgrade to a 430-family unit of the same bore without re-checking C, C0 and the 40 kN Cu.
- An unloaded 4T-432212U near 2,800 r/min lets rollers skid; ensure a minimum load or light spring preload on high-speed positions.
- Lubricant must reach both rows: a housing groove aligned to the cup mid-width of 4T-432212U feeds the two roller complements evenly; a single-side feed starves the far row.
- An unloaded 4T-432212U near 2,800 r/min lets rollers skid; ensure a minimum load or light spring preload on high-speed positions.
- The 247/330 kN ratings and 40 kN Cu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 4T-432212U; internal geometry legitimately differs between manufacturers, so re-verify ratings, clearance class and suffix before substituting another make on a rated drive.
Frequently asked questions
What are the dimensions and catalogue ratings of NTN 4T-432212U?
4T-432212U is a double-row tapered roller bearing of TDO (back-to-back) construction: 60 mm bore, 110 mm outside diameter and 66 mm overall width. From NTN Ball and Roller Bearings CAT.No.2203E: C 247 kN, C0 330 kN, Cu 40 kN, grease limiting speed 2,800 r/min, oil speed 3,800 r/min, mass about 2.49 kg. It is an open, preset-clearance unit with pressed-steel cages.
What is the difference between the NTN 430 and 432 double-row series at 60 mm bore?
Both are TDO double-row tapered roller units, but 430 is the light plan and 432 the heavy plan: at the same bore the 432 execution is wider and heavier with higher load ratings. 4T-432212U belongs to the heavy-duty 432-family TDO double-row series. Large sizes continue the plans as 4130/4131/4230/4231 (430 family) and 3230/3231 (432 family).
Can the internal clearance of 4T-432212U be adjusted at mounting?
No. The TDO unit — two cone assemblies against one double cup — is ground and set by NTN at the factory, and the 66 mm overall width is the finished dimension. Mounting sets no end play: seat the unit square, clamp the cup uniformly and verify free rotation. Field re-adjustment overloads one row.
What do the suffix letters on 432212U mean?
Suffix reading on 432212U: U marks the uprated/reinforced internal design, a separate order number with higher capacity than the basic execution; suffixed variants are separate order numbers and are not interchangeable articles.
Why does 4T-432212U list two speeds, 2,800 and 3,800 r/min?
The lower figure, 2,800 r/min, is the grease-lubricated limiting speed for the two rows and their cages. With oil lubrication NTN rates 4T-432212U at 3,800 r/min because oil removes heat from both roller rows better — the housing feed must reach both rows through the double cup.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN 2203E 2026-09-25 on 2026-10-01. Read our editorial & correction policy.