432220XU bearing: complete specifications & equivalents
The 432220XU is a ANSI ABMA 19.2 radial bearing sized 100 x 180 x 107 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 100 mm |
| Outer diameter D | 180 mm |
| Width B | 107 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel |
| Basic dynamic load rating C | 630 kN |
| Basic static load rating C0 | 925 kN |
| Fatigue load limit Pu | 102 kN |
| Limiting speed (mechanical) | 1700 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 11000 g |
| Manufacturer designation | NTN 4T-432220XU |
| Standard | ANSI ABMA 19.2 |
| Catalog version | NTN 2203E 2026-09-25 |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN 2203E 2026-09-25) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN 2203E 2026-09-25); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 4t-432-series range
| Bore d | 3.937 in |
|---|---|
| Outer diameter D | 7.087 in |
| Width B | 4.213 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 40 mm |
| Smallest bore in 4t-432-series | 40 mm |
| Largest outer diameter in 4t-432-series | 790 mm |
| Width range across 4t-432-series | 46–266 mm |
| Bore position in 4t-432-series (smallest first) | 13 of 39 |
| Bore above smallest 4t-432-series size | 60 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 432220XU | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; brand-specific OEM equivalents (NSK/FAG/NTN) pending multi-source data. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 432220XU model number is decoded
The NTN 2203E double-row table prints 4T-432220XU at 100 mm bore, 180 mm OD and 107 mm overall width, with a grease limiting speed of 1,700 r/min and an oil ceiling of 2,200 r/min. Suffix reading on 432220XU: U marks the uprated/reinforced internal design, a separate order number with higher capacity than the basic execution; X marks the boundary-dimension revision of the base number (D and width differ from the plain number of the same bore); suffixed variants are separate order numbers and are not interchangeable articles. Grease relubrication at the 1,700 r/min limiting speed must reach both roller rows; sustaining 2,200 r/min needs an oil supply with defined flow through the double cup. TDO construction means the two cone assemblies of 4T-432220XU face away from each other inside one double cup: the load lines diverge outward, giving a wide effective spread and high moment stiffness for the 100 mm shaft. The open unit carries no seals; the housing of 4T-432220XU must provide sealing and the grease fill or oil feed to both rows.
Typical equipment & failure modes
Common applications
- large mixer and agitator shafts
- heavy gearbox and mill drive shafts
- crusher and screening-plant main shafts
- large fan and blower shafts with thrust reversal
Known failure patterns
- roller large-end smearing against the cone ribs when one row of the unit runs starved of lubricant
- brinelling of both rows from a mounting blow transmitted through the roller complements
- preload loss and hammering noise when the cup clamping loosens and the unit gains axial float
- cage fatigue after continuous running near the grease limiting speed without oil cooling
- water-induced pitting when washdown reaches the open unit without external seals
Selection pitfalls — read before you substitute
- Mount the 100 mm unit by induction heating (max 120 °C); at 11 kg a cocked lift damages the cages and ribs before the bearing ever runs.
- The 432 heavy plan gives 4T-432220XU its 107 mm width and 630 kN rating at the 100 mm bore; do not downgrade to a 430-family unit of the same bore without re-checking C, C0 and the 102 kN Cu.
- The internal clearance of 4T-432220XU is factory-set: no end-play adjustment exists at mounting, and any attempt to set preload with a shaft nut overloads one row.
- Open 4T-432220XU units have no seals: the housing must seal both rows or the 1,700 r/min grease figure is meaningless once contamination enters.
- An unloaded 4T-432220XU near 1,700 r/min lets rollers skid; ensure a minimum load or light spring preload on high-speed positions.
- The 630/925 kN ratings and 102 kN Cu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 4T-432220XU; internal geometry legitimately differs between manufacturers, so re-verify ratings, clearance class and suffix before substituting another make on a rated drive.
Frequently asked questions
What are the dimensions and catalogue ratings of NTN 4T-432220XU?
4T-432220XU is a double-row tapered roller bearing of TDO (back-to-back) construction: 100 mm bore, 180 mm outside diameter and 107 mm overall width. From NTN Ball and Roller Bearings CAT.No.2203E: C 630 kN, C0 925 kN, Cu 102 kN, grease limiting speed 1,700 r/min, oil speed 2,200 r/min, mass about 11 kg. It is an open, preset-clearance unit with pressed-steel cages.
What is the difference between the NTN 430 and 432 double-row series at 100 mm bore?
Both are TDO double-row tapered roller units, but 430 is the light plan and 432 the heavy plan: at the same bore the 432 execution is wider and heavier with higher load ratings. 4T-432220XU belongs to the heavy-duty 432-family TDO double-row series. Large sizes continue the plans as 4130/4131/4230/4231 (430 family) and 3230/3231 (432 family).
Can the internal clearance of 4T-432220XU be adjusted at mounting?
No. The TDO unit — two cone assemblies against one double cup — is ground and set by NTN at the factory, and the 107 mm overall width is the finished dimension. Mounting sets no end play: seat the unit square, clamp the cup uniformly and verify free rotation. Field re-adjustment overloads one row.
What do the suffix letters on 432220XU mean?
Suffix reading on 432220XU: U marks the uprated/reinforced internal design, a separate order number with higher capacity than the basic execution; X marks the boundary-dimension revision of the base number (D and width differ from the plain number of the same bore); suffixed variants are separate order numbers and are not interchangeable articles.
Why does 4T-432220XU list two speeds, 1,700 and 2,200 r/min?
The lower figure, 1,700 r/min, is the grease-lubricated limiting speed for the two rows and their cages. With oil lubrication NTN rates 4T-432220XU at 2,200 r/min because oil removes heat from both roller rows better — the housing feed must reach both rows through the double cup.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN 2203E 2026-09-25 on 2026-10-01. Read our editorial & correction policy.