07087-07196 bearing: complete specifications & equivalents
The 07087-07196 is a ANSI ABMA 19.2 radial bearing sized 22.225 x 50.005 x 13.495 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 22.225 mm |
| Outer diameter D | 50.005 mm |
| Width B | 13.495 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel |
| Basic dynamic load rating C | 28.8 kN |
| Basic static load rating C0 | 27.9 kN |
| Limiting speed (mechanical) | 7500 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 128 g |
| Manufacturer designation | NTN 4T-07087/07196 |
| Standard | ANSI ABMA 19.2 |
| Catalog version | NTN 2203E 2026-09-25 |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN 2203E 2026-09-25) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN 2203E 2026-09-25); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 4t-inch-series range
| Bore d | 0.875 in |
|---|---|
| Outer diameter D | 1.969 in |
| Width B | 0.531 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 13.9 mm |
| Smallest bore in 4t-inch-series | 12.7 mm |
| Largest outer diameter in 4t-inch-series | 260 mm |
| Width range across 4t-inch-series | 10.998–77.788 mm |
| Bore position in 4t-inch-series (smallest first) | 13 of 148 |
| Bore above smallest 4t-inch-series size | 9.525000000000002 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 07087 | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; brand-specific OEM equivalents (NSK/FAG/NTN) pending multi-source data. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 07087-07196 model number is decoded
NTN supplies this 0.875 in (22.225 mm) shaft position as 4T-07087/07196: cone 07087, cup 07196, profiled rollers and a pressed-steel cage, rated 28.8 kN basic dynamic and 27.9 kN static. The 4T prefix is NTN's tapered roller quality mark stamped on both parts; it is a brand mark, not a size code, so cross-references quote 07087/07196 without it. The 1.3 kN of dynamic capacity per millimetre of bore summarises the 28.8 kN rating over the 22.225 mm bore — sanity-check any interchange candidate against this ratio and the 13.495 mm T. Cup-side note for 07196: within the pure-numeric inch family tables the 07087 cone is listed against several cup options, and it is the cup that fixes the 50.005 mm OD and the 13.495 mm assembled width — quote the full 07087/07196 pair, never the cone alone. NTN grades inch 4T bearings as open bearings without integral seals; at 22.225 mm bore the application supplies sealing and the grease fill or oil feed.
Typical equipment & failure modes
Common applications
- light trailer and boat-trailer wheel hubs
- small agricultural implement wheels and auger drives
- lawn, garden and powersport axle positions
- small inch-shaft gearbox and reducer shafts
Known failure patterns
- rib-face scoring when the thrust share of the combined load exceeds what the cone rib of this size carries
- flaking on one cone only when a bent shaft loads the O/X pair unevenly
- cup creep and housing fretting when the cup seat is cut too loose for the rotating load
- cage fatigue when the pair runs continuously near the grease limiting speed without oil cooling
- brinell marks on cone and cup raceways from impact during handling or hammer fitting
Selection pitfalls — read before you substitute
- At 22.225 mm (0.875 in) bore the thin cone and cup distort under an over-tight shaft nut; set the 4T-07087/07196 pair with a dial indicator on end play rather than by locknut feel.
- The pure-numeric inch family at 22.225 mm bore (50.005×13.495 mm assembled) is one of several inch families sharing similar bores; cross-series swaps change OD, T and contact angle, so match the full 07087/07196 reference at purchase.
- Replacing one half of an adjusted pair without resetting end play negates the 13.495 mm T logic: re-adjust the set and re-verify the contact pattern rather than reusing the old spacer stack.
- Never drive the 50.005 mm cup home through the rollers: fitting force goes through the ring faces only, or brinell marks release as noise within the first running hours.
- An unloaded 4T-07087/07196 near 7,500 r/min lets rollers skid and smear the cone rib; spring-preload lightly loaded high-speed pairs.
- The 28.8/27.9 kN ratings here are NTN Ball and Roller Bearings CAT.No.2203E figures for 4T-07087/07196; internal geometry legitimately differs between inch-series makers, so re-verify ratings, adjustment and the exact cone/cup references before substituting another brand on a rated drive.
Frequently asked questions
What are the dimensions and catalogue ratings of NTN 4T-07087/07196?
4T-07087/07196 is an inch-series single-row tapered roller bearing to the ABMA boundary plan: 22.225 mm bore (0.875 in), 50.005 mm outside diameter and 13.495 mm assembled width T (1.969 × 0.531 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 28.8 kN, C0 27.9 kN, grease limiting speed 7,500 r/min, oil speed 10,000 r/min, mass about 128 g. It is an open, separable cone/cup set with a pressed-steel cage.
Are the cone and cup of 4T-07087/07196 interchangeable separately?
Yes — ABMA inch parts are individually interchangeable: the 07087 cone or the 07196 cup can be replaced by an identical reference from NTN or another ABMA-dimensioned maker. Pairing the cone with a different cup reference is a different catalogue row: OD, assembled T and the 28.8/27.9 kN ratings change with the cup.
What is the difference between 4T-07087/07196 and a metric ISO 355 tapered bearing?
4T-07087/07196 follows the ABMA inch boundary plan with cone/cup references; ISO 355 bearings use metric dimension-series numbers (302, 322, …). Even where a metric size looks close to 22.225×50.005×13.495 mm, the envelopes and contact angles differ — the two systems are not drop-in interchangeable; check every boundary value before substituting.
What does the 4T prefix on 4T-07087/07196 mean?
4T is NTN's tapered roller bearing quality mark, stamped on cone and cup in the factory. It identifies NTN's 4T programme and is not a dimension or variant code, so interchange lists quote the bare 07087/07196 references; the 4T spelling is retained among this page's search aliases.
Why does 4T-07087/07196 list two speeds, 7,500 and 10,000 r/min?
The lower figure, 7,500 r/min, is the grease-lubricated limiting speed — the mechanical ceiling for the cage, rollers and cone-rib contact. With oil lubrication NTN rates 4T-07087/07196 at 10,000 r/min because oil removes rib-contact heat better. Real limits still depend on pair adjustment, oil flow and cooling.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN 2203E 2026-09-25 on 2026-10-01. Read our editorial & correction policy.