07100S-07196 bearing: complete specifications & equivalents
The 07100S-07196 is a ANSI ABMA 19.2 radial bearing sized 25.4 x 50.005 x 13.495 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 25.4 mm |
| Outer diameter D | 50.005 mm |
| Width B | 13.495 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel |
| Basic dynamic load rating C | 28.8 kN |
| Basic static load rating C0 | 27.9 kN |
| Limiting speed (mechanical) | 7500 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 114 g |
| Manufacturer designation | NTN 4T-07100S/07196 |
| Standard | ANSI ABMA 19.2 |
| Catalog version | NTN 2203E 2026-09-25 |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN 2203E 2026-09-25) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN 2203E 2026-09-25); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 4t-inch-series range
| Bore d | 1 in |
|---|---|
| Outer diameter D | 1.969 in |
| Width B | 0.531 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 12.3 mm |
| Smallest bore in 4t-inch-series | 12.7 mm |
| Largest outer diameter in 4t-inch-series | 260 mm |
| Width range across 4t-inch-series | 10.998–77.788 mm |
| Bore position in 4t-inch-series (smallest first) | 19 of 148 |
| Bore above smallest 4t-inch-series size | 12.7 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 07100S | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; brand-specific OEM equivalents (NSK/FAG/NTN) pending multi-source data. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 07100S-07196 model number is decoded
The NTN 2203E inch table prints 4T-07100S/07196 at 25.4 mm bore (1 in), 50.005 mm cup OD and 13.495 mm assembled T, with a grease limiting speed of 7,500 r/min and an oil ceiling of 10,000 r/min. Cone and cup of 4T-07100S/07196 are separately stocked parts: a worn 07196 cup can be replaced against the existing 07100S cone, provided the new cup carries the identical reference — pairing across references changes the 13.495 mm assembled width and the rating. Speed planning uses both catalogue columns: grease 7,500 r/min is the mechanical ceiling for 4T-07100S/07196, oil 10,000 r/min with circulating oil — a 2,500 r/min margin at this size. Cup-side note for 07196: within the pure-numeric inch family tables the 07100S cone is listed against several cup options, and it is the cup that fixes the 50.005 mm OD and the 13.495 mm assembled width — quote the full 07100S/07196 pair, never the cone alone. Back-to-back (O) and face-to-face (X) arrangements of two 4T-07100S/07196 sets react differently to shaft bending; choose the orientation for the moment load before locking shoulder geometry.
Typical equipment & failure modes
Common applications
- machine-tool headstocks on inch spindles
- pump and blower drive shafts with combined load
- truck and trailer axle hubs on inch-dimensioned axles
- agricultural tractor transmission and PTO shafts
Known failure patterns
- cone-rib and roller large-end smearing when the adjusted pair runs with preload but starved lubricant film
- preload loss and noise after one bearing of the adjusted pair is replaced without resetting end play
- false brinelling on a stationary pair exposed to vibration during transport or standby
- cage fatigue when the pair runs continuously near the grease limiting speed without oil cooling
- rolling-contact fatigue spalling after the catalogue L10 life at the actual combined load
Selection pitfalls — read before you substitute
- Hub and pinion positions of this 25.4 mm class are adjusted in pairs; verify end play against the axle or gearbox drawing and re-torque after bedding-in instead of trusting the first setting on 4T-07100S/07196.
- The pure-numeric inch family at 25.4 mm bore (50.005×13.495 mm assembled) is one of several inch families sharing similar bores; cross-series swaps change OD, T and contact angle, so match the full 07100S/07196 reference at purchase.
- ABMA makes the 25.4×50.005 mm envelope interchangeable, not the ratings: NTN prints 28.8/27.9 kN for this execution and another make of the same number can differ in roller complement.
- Fit selection follows the rotating ring: a rotating cone on a 25.4 mm shaft takes a k5/m5 seat, and a rotating cup reverses the logic — decide from the load diagram, not from habit.
- An unloaded 4T-07100S/07196 near 7,500 r/min lets rollers skid and smear the cone rib; spring-preload lightly loaded high-speed pairs.
- The 28.8/27.9 kN ratings here are NTN Ball and Roller Bearings CAT.No.2203E figures for 4T-07100S/07196; internal geometry legitimately differs between inch-series makers, so re-verify ratings, adjustment and the exact cone/cup references before substituting another brand on a rated drive.
Frequently asked questions
What are the dimensions and catalogue ratings of NTN 4T-07100S/07196?
4T-07100S/07196 is an inch-series single-row tapered roller bearing to the ABMA boundary plan: 25.4 mm bore (1 in), 50.005 mm outside diameter and 13.495 mm assembled width T (1.969 × 0.531 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 28.8 kN, C0 27.9 kN, grease limiting speed 7,500 r/min, oil speed 10,000 r/min, mass about 114 g. It is an open, separable cone/cup set with a pressed-steel cage.
Are the cone and cup of 4T-07100S/07196 interchangeable separately?
Yes — ABMA inch parts are individually interchangeable: the 07100S cone or the 07196 cup can be replaced by an identical reference from NTN or another ABMA-dimensioned maker. Pairing the cone with a different cup reference is a different catalogue row: OD, assembled T and the 28.8/27.9 kN ratings change with the cup.
What is the difference between 4T-07100S/07196 and a metric ISO 355 tapered bearing?
4T-07100S/07196 follows the ABMA inch boundary plan with cone/cup references; ISO 355 bearings use metric dimension-series numbers (302, 322, …). Even where a metric size looks close to 25.4×50.005×13.495 mm, the envelopes and contact angles differ — the two systems are not drop-in interchangeable; check every boundary value before substituting.
What does the 4T prefix on 4T-07100S/07196 mean?
4T is NTN's tapered roller bearing quality mark, stamped on cone and cup in the factory. It identifies NTN's 4T programme and is not a dimension or variant code, so interchange lists quote the bare 07100S/07196 references; the 4T spelling is retained among this page's search aliases.
Why does 4T-07100S/07196 list two speeds, 7,500 and 10,000 r/min?
The lower figure, 7,500 r/min, is the grease-lubricated limiting speed — the mechanical ceiling for the cage, rollers and cone-rib contact. With oil lubrication NTN rates 4T-07100S/07196 at 10,000 r/min because oil removes rib-contact heat better. Real limits still depend on pair adjustment, oil flow and cooling.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN 2203E 2026-09-25 on 2026-10-01. Read our editorial & correction policy.