14116-14274 bearing: complete specifications & equivalents
The 14116-14274 is a ANSI ABMA 19.2 radial bearing sized 30.226 x 69.012 x 19.845 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 30.226 mm |
| Outer diameter D | 69.012 mm |
| Width B | 19.845 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel |
| Basic dynamic load rating C | 53.5 kN |
| Basic static load rating C0 | 58 kN |
| Limiting speed (mechanical) | 5600 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 369 g |
| Manufacturer designation | NTN 4T-14116/14274 |
| Standard | ANSI ABMA 19.2 |
| Catalog version | NTN 2203E 2026-09-25 |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN 2203E 2026-09-25) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN 2203E 2026-09-25); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 4t-inch-series range
| Bore d | 1.19 in |
|---|---|
| Outer diameter D | 2.717 in |
| Width B | 0.781 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 19.4 mm |
| Smallest bore in 4t-inch-series | 12.7 mm |
| Largest outer diameter in 4t-inch-series | 260 mm |
| Width range across 4t-inch-series | 10.998–77.788 mm |
| Bore position in 4t-inch-series (smallest first) | 31 of 148 |
| Bore above smallest 4t-inch-series size | 17.526 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 14116-14276 | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same NTN cone 4T-14116 paired with a different cup (14276): cone interchangeable, cup differs — OD, assembled width T and ratings follow the cup. Verify the full cone/cup reference before substituting. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 14116-14274 model number is decoded
The NTN 2203E inch table prints 4T-14116/14274 at 30.226 mm bore (1.19 in), 69.012 mm cup OD and 19.845 mm assembled T, with a grease limiting speed of 5,600 r/min and an oil ceiling of 7,400 r/min. The 4T prefix is NTN's tapered roller quality mark stamped on both parts; it is a brand mark, not a size code, so cross-references quote 14116/14274 without it. Catalogue mass of the 4T-14116/14274 cone-plus-cup set is 369 g; shaft and housing shoulders must carry that mass square to the axis during fitting. Cup-side note for 14274: within the pure-numeric inch family tables the 14116 cone is listed against several cup options, and it is the cup that fixes the 69.012 mm OD and the 19.845 mm assembled width — quote the full 14116/14274 pair, never the cone alone. The rollers run with their large ends against the cone's guide rib; lubricant must reach that rib face of 4T-14116/14274, not only the raceway, or the pair smears on the first overloaded start.
Typical equipment & failure modes
Common applications
- pump and blower drive shafts with combined load
- truck and trailer axle hubs on inch-dimensioned axles
- agricultural tractor transmission and PTO shafts
- industrial gearboxes built to inch shafting
Known failure patterns
- cone-rib and roller large-end smearing when the adjusted pair runs with preload but starved lubricant film
- flaking on one cone only when a bent shaft loads the O/X pair unevenly
- cup creep and housing fretting when the cup seat is cut too loose for the rotating load
- cage fatigue when the pair runs continuously near the grease limiting speed without oil cooling
- rolling-contact fatigue spalling after the catalogue L10 life at the actual combined load
Selection pitfalls — read before you substitute
- Hub and pinion positions of this 30.226 mm class are adjusted in pairs; verify end play against the axle or gearbox drawing and re-torque after bedding-in instead of trusting the first setting on 4T-14116/14274.
- The pure-numeric inch family at 30.226 mm bore (69.012×19.845 mm assembled) is one of several inch families sharing similar bores; cross-series swaps change OD, T and contact angle, so match the full 14116/14274 reference at purchase.
- Do not confuse T (19.845 mm, the assembled cone-plus-cup width) with the cone width when drawing spacers; an abutment sized to T leaves the cup unseated.
- Fit selection follows the rotating ring: a rotating cone on a 30.226 mm shaft takes a k5/m5 seat, and a rotating cup reverses the logic — decide from the load diagram, not from habit.
- Open 4T-14116/14274 sets have no seals: a hub or gearbox needs external sealing or the 5,600 r/min grease figure is meaningless once water reaches the cone rib.
- The 53.5/58 kN ratings here are NTN Ball and Roller Bearings CAT.No.2203E figures for 4T-14116/14274; internal geometry legitimately differs between inch-series makers, so re-verify ratings, adjustment and the exact cone/cup references before substituting another brand on a rated drive.
Frequently asked questions
What are the dimensions and catalogue ratings of NTN 4T-14116/14274?
4T-14116/14274 is an inch-series single-row tapered roller bearing to the ABMA boundary plan: 30.226 mm bore (1.19 in), 69.012 mm outside diameter and 19.845 mm assembled width T (2.717 × 0.781 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 53.5 kN, C0 58 kN, grease limiting speed 5,600 r/min, oil speed 7,400 r/min, mass about 369 g. It is an open, separable cone/cup set with a pressed-steel cage.
Are the cone and cup of 4T-14116/14274 interchangeable separately?
Yes — ABMA inch parts are individually interchangeable: the 14116 cone or the 14274 cup can be replaced by an identical reference from NTN or another ABMA-dimensioned maker. Pairing the cone with a different cup reference is a different catalogue row: OD, assembled T and the 53.5/58 kN ratings change with the cup.
What is the difference between 4T-14116/14274 and a metric ISO 355 tapered bearing?
4T-14116/14274 follows the ABMA inch boundary plan with cone/cup references; ISO 355 bearings use metric dimension-series numbers (302, 322, …). Even where a metric size looks close to 30.226×69.012×19.845 mm, the envelopes and contact angles differ — the two systems are not drop-in interchangeable; check every boundary value before substituting.
What does the 4T prefix on 4T-14116/14274 mean?
4T is NTN's tapered roller bearing quality mark, stamped on cone and cup in the factory. It identifies NTN's 4T programme and is not a dimension or variant code, so interchange lists quote the bare 14116/14274 references; the 4T spelling is retained among this page's search aliases.
Why does 4T-14116/14274 list two speeds, 5,600 and 7,400 r/min?
The lower figure, 5,600 r/min, is the grease-lubricated limiting speed — the mechanical ceiling for the cage, rollers and cone-rib contact. With oil lubrication NTN rates 4T-14116/14274 at 7,400 r/min because oil removes rib-contact heat better. Real limits still depend on pair adjustment, oil flow and cooling.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN 2203E 2026-09-25 on 2026-10-01. Read our editorial & correction policy.