14137A-14276-NTN bearing: complete specifications & equivalents
The 14137A-14276-NTN is a ANSI ABMA 19.2 radial bearing sized 34.925 x 69.012 x 19.845 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 34.925 mm |
| Outer diameter D | 69.012 mm |
| Width B | 19.845 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel |
| Basic dynamic load rating C | 53.5 kN |
| Basic static load rating C0 | 58 kN |
| Limiting speed (mechanical) | 5600 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 334 g |
| Manufacturer designation | NTN 4T-14137A/14276 |
| Standard | ANSI ABMA 19.2 |
| Catalog version | NTN 2203E 2026-09-25 |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN 2203E 2026-09-25) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN 2203E 2026-09-25); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 4t-inch-series range
| Bore d | 1.375 in |
|---|---|
| Outer diameter D | 2.717 in |
| Width B | 0.781 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 17 mm |
| Smallest bore in 4t-inch-series | 12.7 mm |
| Largest outer diameter in 4t-inch-series | 260 mm |
| Width range across 4t-inch-series | 10.998–77.788 mm |
| Bore position in 4t-inch-series (smallest first) | 34 of 148 |
| Bore above smallest 4t-inch-series size | 22.224999999999998 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 14137A-14276 | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 34.925×69.012×19.845 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 14137A-14276-NTN model number is decoded
In NTN Ball and Roller Bearings CAT.No.2203E, the order number 4T-14137A/14276 denotes the pure-numeric inch family of NTN inch tapered roller bearings — cone 14137A and cup 14276 delivered as a matched, separable pair of 34.925 mm bore and 69.012 mm outside diameter. Cone and cup of 4T-14137A/14276 are separately stocked parts: a worn 14276 cup can be replaced against the existing 14137A cone, provided the new cup carries the identical reference — pairing across references changes the 19.845 mm assembled width and the rating. Selection: C 53.5 kN against C0 58 kN gives a C0/C ratio of 1.08 for the 34.925 mm bore; the pair is counted as one adjusted unit when checking L10 at the equivalent combined load. Housing fitment sequence for 4T-14137A/14276: press the 14276 cup square into the 69.012 mm seat first, then bring the 14137A cone (on its 34.925 mm shaft) into adjustment — the two references are separate engineering parts that happen to ship as one set. A single-row tapered bearing reacts thrust in one direction only; 4T-14137A/14276 is adjusted against a second bearing so the shaft is located in both directions.
Typical equipment & failure modes
Common applications
- machine-tool headstocks on inch spindles
- pump and blower drive shafts with combined load
- truck and trailer axle hubs on inch-dimensioned axles
- agricultural tractor transmission and PTO shafts
Known failure patterns
- cone-rib and roller large-end smearing when the adjusted pair runs with preload but starved lubricant film
- preload loss and noise after one bearing of the adjusted pair is replaced without resetting end play
- false brinelling on a stationary pair exposed to vibration during transport or standby
- cage fatigue when the pair runs continuously near the grease limiting speed without oil cooling
- fretting corrosion on a loose cone seat that creeps under rotating load
Selection pitfalls — read before you substitute
- Hub and pinion positions of this 34.925 mm class are adjusted in pairs; verify end play against the axle or gearbox drawing and re-torque after bedding-in instead of trusting the first setting on 4T-14137A/14276.
- The pure-numeric inch family at 34.925 mm bore (69.012×19.845 mm assembled) is one of several inch families sharing similar bores; cross-series swaps change OD, T and contact angle, so match the full 14137A/14276 reference at purchase.
- Replacing one half of an adjusted pair without resetting end play negates the 19.845 mm T logic: re-adjust the set and re-verify the contact pattern rather than reusing the old spacer stack.
- Inch and metric bores collide on paper — 34.925 mm is 1.375 in, not a round metric size; a metric bearing that seems 0.1 mm off will not seat on the inch shaft.
- Open 4T-14137A/14276 sets have no seals: a hub or gearbox needs external sealing or the 5,600 r/min grease figure is meaningless once water reaches the cone rib.
- The 53.5/58 kN ratings here are NTN Ball and Roller Bearings CAT.No.2203E figures for 4T-14137A/14276; internal geometry legitimately differs between inch-series makers, so re-verify ratings, adjustment and the exact cone/cup references before substituting another brand on a rated drive.
Frequently asked questions
What are the dimensions and catalogue ratings of NTN 4T-14137A/14276?
4T-14137A/14276 is an inch-series single-row tapered roller bearing to the ABMA boundary plan: 34.925 mm bore (1.375 in), 69.012 mm outside diameter and 19.845 mm assembled width T (2.717 × 0.781 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 53.5 kN, C0 58 kN, grease limiting speed 5,600 r/min, oil speed 7,400 r/min, mass about 334 g. It is an open, separable cone/cup set with a pressed-steel cage.
Are the cone and cup of 4T-14137A/14276 interchangeable separately?
Yes — ABMA inch parts are individually interchangeable: the 14137A cone or the 14276 cup can be replaced by an identical reference from NTN or another ABMA-dimensioned maker. Pairing the cone with a different cup reference is a different catalogue row: OD, assembled T and the 53.5/58 kN ratings change with the cup.
What is the difference between 4T-14137A/14276 and a metric ISO 355 tapered bearing?
4T-14137A/14276 follows the ABMA inch boundary plan with cone/cup references; ISO 355 bearings use metric dimension-series numbers (302, 322, …). Even where a metric size looks close to 34.925×69.012×19.845 mm, the envelopes and contact angles differ — the two systems are not drop-in interchangeable; check every boundary value before substituting.
What does the 4T prefix on 4T-14137A/14276 mean?
4T is NTN's tapered roller bearing quality mark, stamped on cone and cup in the factory. It identifies NTN's 4T programme and is not a dimension or variant code, so interchange lists quote the bare 14137A/14276 references; the 4T spelling is retained among this page's search aliases.
Why does 4T-14137A/14276 list two speeds, 5,600 and 7,400 r/min?
The lower figure, 5,600 r/min, is the grease-lubricated limiting speed — the mechanical ceiling for the cage, rollers and cone-rib contact. With oil lubrication NTN rates 4T-14137A/14276 at 7,400 r/min because oil removes rib-contact heat better. Real limits still depend on pair adjustment, oil flow and cooling.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN 2203E 2026-09-25 on 2026-10-01. Read our editorial & correction policy.