15118-15245 bearing: complete specifications & equivalents
The 15118-15245 is a ANSI ABMA 19.2 radial bearing sized 30.213 x 62 x 19.05 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 30.213 mm |
| Outer diameter D | 62 mm |
| Width B | 19.05 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel |
| Basic dynamic load rating C | 52 kN |
| Basic static load rating C0 | 54 kN |
| Limiting speed (mechanical) | 6100 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 266 g |
| Manufacturer designation | NTN 4T-15118/15245 |
| Standard | ANSI ABMA 19.2 |
| Catalog version | NTN 2203E 2026-09-25 |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN 2203E 2026-09-25) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN 2203E 2026-09-25); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 4t-inch-series range
| Bore d | 1.189 in |
|---|---|
| Outer diameter D | 2.441 in |
| Width B | 0.75 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 15.9 mm |
| Smallest bore in 4t-inch-series | 12.7 mm |
| Largest outer diameter in 4t-inch-series | 260 mm |
| Width range across 4t-inch-series | 10.998–77.788 mm |
| Bore position in 4t-inch-series (smallest first) | 30 of 148 |
| Bore above smallest 4t-inch-series size | 17.513 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 15118 | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; brand-specific OEM equivalents (NSK/FAG/NTN) pending multi-source data. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 15118-15245 model number is decoded
4T-15118/15245 is an NTN inch-series single-row tapered roller bearing: a separable cone-and-cup pair on the ABMA inch boundary plan, 30.213×62×19.05 mm (assembled width T), for a shaft of about 30.213 mm (1.189 in). The 4T prefix is NTN's tapered roller quality mark stamped on both parts; it is a brand mark, not a size code, so cross-references quote 15118/15245 without it. Speed planning uses both catalogue columns: grease 6,100 r/min is the mechanical ceiling for 4T-15118/15245, oil 8,200 r/min with circulating oil — a 2,100 r/min margin at this size. The printed 52/54 kN ratings belong to the assembled 15118+15245 pair; a sibling row using the same cone with a different cup carries its own rating row because the raceway track shifts with the cup. The rollers run with their large ends against the cone's guide rib; lubricant must reach that rib face of 4T-15118/15245, not only the raceway, or the pair smears on the first overloaded start.
Typical equipment & failure modes
Common applications
- industrial gearboxes built to inch shafting
- construction-equipment pivot and wheel positions
- mining and quarry conveyor drive pulleys
- machine-tool headstocks on inch spindles
Known failure patterns
- rib-face scoring when the thrust share of the combined load exceeds what the cone rib of this size carries
- preload loss and noise after one bearing of the adjusted pair is replaced without resetting end play
- false brinelling on a stationary pair exposed to vibration during transport or standby
- cage damage from a mounting blow transmitted through the roller complement
- water-induced pitting when the open bearing sees washdown without external seals
Selection pitfalls — read before you substitute
- Hub and pinion positions of this 30.213 mm class are adjusted in pairs; verify end play against the axle or gearbox drawing and re-torque after bedding-in instead of trusting the first setting on 4T-15118/15245.
- The pure-numeric inch family at 30.213 mm bore (62×19.05 mm assembled) is one of several inch families sharing similar bores; cross-series swaps change OD, T and contact angle, so match the full 15118/15245 reference at purchase.
- An unloaded 4T-15118/15245 near 6,100 r/min lets rollers skid and smear the cone rib; spring-preload lightly loaded high-speed pairs.
- Inch and metric bores collide on paper — 30.213 mm is 1.189 in, not a round metric size; a metric bearing that seems 0.1 mm off will not seat on the inch shaft.
- Shaft and housing fillets must clear the ring chamfers of 15118 and 15245; use undercut shoulders so the rings seat on the face, not on a radius.
- The 52/54 kN ratings here are NTN Ball and Roller Bearings CAT.No.2203E figures for 4T-15118/15245; internal geometry legitimately differs between inch-series makers, so re-verify ratings, adjustment and the exact cone/cup references before substituting another brand on a rated drive.
Frequently asked questions
What are the dimensions and catalogue ratings of NTN 4T-15118/15245?
4T-15118/15245 is an inch-series single-row tapered roller bearing to the ABMA boundary plan: 30.213 mm bore (1.189 in), 62 mm outside diameter and 19.05 mm assembled width T (2.441 × 0.75 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 52 kN, C0 54 kN, grease limiting speed 6,100 r/min, oil speed 8,200 r/min, mass about 266 g. It is an open, separable cone/cup set with a pressed-steel cage.
Are the cone and cup of 4T-15118/15245 interchangeable separately?
Yes — ABMA inch parts are individually interchangeable: the 15118 cone or the 15245 cup can be replaced by an identical reference from NTN or another ABMA-dimensioned maker. Pairing the cone with a different cup reference is a different catalogue row: OD, assembled T and the 52/54 kN ratings change with the cup.
What is the difference between 4T-15118/15245 and a metric ISO 355 tapered bearing?
4T-15118/15245 follows the ABMA inch boundary plan with cone/cup references; ISO 355 bearings use metric dimension-series numbers (302, 322, …). Even where a metric size looks close to 30.213×62×19.05 mm, the envelopes and contact angles differ — the two systems are not drop-in interchangeable; check every boundary value before substituting.
What does the 4T prefix on 4T-15118/15245 mean?
4T is NTN's tapered roller bearing quality mark, stamped on cone and cup in the factory. It identifies NTN's 4T programme and is not a dimension or variant code, so interchange lists quote the bare 15118/15245 references; the 4T spelling is retained among this page's search aliases.
Why does 4T-15118/15245 list two speeds, 6,100 and 8,200 r/min?
The lower figure, 6,100 r/min, is the grease-lubricated limiting speed — the mechanical ceiling for the cage, rollers and cone-rib contact. With oil lubrication NTN rates 4T-15118/15245 at 8,200 r/min because oil removes rib-contact heat better. Real limits still depend on pair adjustment, oil flow and cooling.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN 2203E 2026-09-25 on 2026-10-01. Read our editorial & correction policy.