1775-1729 bearing: complete specifications & equivalents
The 1775-1729 is a ANSI ABMA 19.2 radial bearing sized 19.05 x 56.896 x 19.368 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 19.05 mm |
| Outer diameter D | 56.896 mm |
| Width B | 19.368 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel |
| Basic dynamic load rating C | 47.5 kN |
| Basic static load rating C0 | 46.5 kN |
| Limiting speed (mechanical) | 7200 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 268 g |
| Manufacturer designation | NTN 4T-1775/1729 |
| Standard | ANSI ABMA 19.2 |
| Catalog version | NTN 2203E 2026-09-25 |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN 2203E 2026-09-25) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN 2203E 2026-09-25); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 4t-inch-series range
| Bore d | 0.75 in |
|---|---|
| Outer diameter D | 2.24 in |
| Width B | 0.763 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 18.9 mm |
| Smallest bore in 4t-inch-series | 12.7 mm |
| Largest outer diameter in 4t-inch-series | 260 mm |
| Width range across 4t-inch-series | 10.998–77.788 mm |
| Bore position in 4t-inch-series (smallest first) | 6 of 148 |
| Bore above smallest 4t-inch-series size | 6.350000000000001 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 1775 | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; brand-specific OEM equivalents (NSK/FAG/NTN) pending multi-source data. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 1775-1729 model number is decoded
The NTN 2203E inch table prints 4T-1775/1729 at 19.05 mm bore (0.75 in), 56.896 mm cup OD and 19.368 mm assembled T, with a grease limiting speed of 7,200 r/min and an oil ceiling of 9,600 r/min. Letter prefixes inherited from the inch convention mark the load family: LM reads as light-medium, HM as heavy-medium, LL as extra-light, J-prefixed codes as metric-envelope families — 1775 sits in the pure-numeric inch family. Speed planning uses both catalogue columns: grease 7,200 r/min is the mechanical ceiling for 4T-1775/1729, oil 9,600 r/min with circulating oil — a 2,400 r/min margin at this size. Housing fitment sequence for 4T-1775/1729: press the 1729 cup square into the 56.896 mm seat first, then bring the 1775 cone (on its 19.05 mm shaft) into adjustment — the two references are separate engineering parts that happen to ship as one set. A single-row tapered bearing reacts thrust in one direction only; 4T-1775/1729 is adjusted against a second bearing so the shaft is located in both directions.
Typical equipment & failure modes
Common applications
- small machine-tool feed and spindle counter-supports
- light trailer and boat-trailer wheel hubs
- small agricultural implement wheels and auger drives
- lawn, garden and powersport axle positions
Known failure patterns
- rib-face scoring when the thrust share of the combined load exceeds what the cone rib of this size carries
- flaking on one cone only when a bent shaft loads the O/X pair unevenly
- cup creep and housing fretting when the cup seat is cut too loose for the rotating load
- cage damage from a mounting blow transmitted through the roller complement
- edge loading when shaft deflection exceeds the few arc-minutes an adjusted pair tolerates
Selection pitfalls — read before you substitute
- At 19.05 mm (0.75 in) bore the thin cone and cup distort under an over-tight shaft nut; set the 4T-1775/1729 pair with a dial indicator on end play rather than by locknut feel.
- The pure-numeric inch family at 19.05 mm bore (56.896×19.368 mm assembled) is one of several inch families sharing similar bores; cross-series swaps change OD, T and contact angle, so match the full 1775/1729 reference at purchase.
- Open 4T-1775/1729 sets have no seals: a hub or gearbox needs external sealing or the 7,200 r/min grease figure is meaningless once water reaches the cone rib.
- ABMA makes the 19.05×56.896 mm envelope interchangeable, not the ratings: NTN prints 47.5/46.5 kN for this execution and another make of the same number can differ in roller complement.
- Do not confuse T (19.368 mm, the assembled cone-plus-cup width) with the cone width when drawing spacers; an abutment sized to T leaves the cup unseated.
- The 47.5/46.5 kN ratings here are NTN Ball and Roller Bearings CAT.No.2203E figures for 4T-1775/1729; internal geometry legitimately differs between inch-series makers, so re-verify ratings, adjustment and the exact cone/cup references before substituting another brand on a rated drive.
Frequently asked questions
What are the dimensions and catalogue ratings of NTN 4T-1775/1729?
4T-1775/1729 is an inch-series single-row tapered roller bearing to the ABMA boundary plan: 19.05 mm bore (0.75 in), 56.896 mm outside diameter and 19.368 mm assembled width T (2.24 × 0.763 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 47.5 kN, C0 46.5 kN, grease limiting speed 7,200 r/min, oil speed 9,600 r/min, mass about 268 g. It is an open, separable cone/cup set with a pressed-steel cage.
Are the cone and cup of 4T-1775/1729 interchangeable separately?
Yes — ABMA inch parts are individually interchangeable: the 1775 cone or the 1729 cup can be replaced by an identical reference from NTN or another ABMA-dimensioned maker. Pairing the cone with a different cup reference is a different catalogue row: OD, assembled T and the 47.5/46.5 kN ratings change with the cup.
What is the difference between 4T-1775/1729 and a metric ISO 355 tapered bearing?
4T-1775/1729 follows the ABMA inch boundary plan with cone/cup references; ISO 355 bearings use metric dimension-series numbers (302, 322, …). Even where a metric size looks close to 19.05×56.896×19.368 mm, the envelopes and contact angles differ — the two systems are not drop-in interchangeable; check every boundary value before substituting.
What does the 4T prefix on 4T-1775/1729 mean?
4T is NTN's tapered roller bearing quality mark, stamped on cone and cup in the factory. It identifies NTN's 4T programme and is not a dimension or variant code, so interchange lists quote the bare 1775/1729 references; the 4T spelling is retained among this page's search aliases.
Why does 4T-1775/1729 list two speeds, 7,200 and 9,600 r/min?
The lower figure, 7,200 r/min, is the grease-lubricated limiting speed — the mechanical ceiling for the cage, rollers and cone-rib contact. With oil lubrication NTN rates 4T-1775/1729 at 9,600 r/min because oil removes rib-contact heat better. Real limits still depend on pair adjustment, oil flow and cooling.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN 2203E 2026-09-25 on 2026-10-01. Read our editorial & correction policy.