2474-2420 bearing: complete specifications & equivalents
The 2474-2420 is a ANSI ABMA 19.2 radial bearing sized 28.575 x 68.262 x 22.225 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 28.575 mm |
| Outer diameter D | 68.262 mm |
| Width B | 22.225 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel |
| Basic dynamic load rating C | 64 kN |
| Basic static load rating C0 | 65.5 kN |
| Limiting speed (mechanical) | 5700 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 380 g |
| Manufacturer designation | NTN 4T-2474/2420 |
| Standard | ANSI ABMA 19.2 |
| Catalog version | NTN 2203E 2026-09-25 |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN 2203E 2026-09-25) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN 2203E 2026-09-25); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 4t-inch-series range
| Bore d | 1.125 in |
|---|---|
| Outer diameter D | 2.687 in |
| Width B | 0.875 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 19.8 mm |
| Smallest bore in 4t-inch-series | 12.7 mm |
| Largest outer diameter in 4t-inch-series | 260 mm |
| Width range across 4t-inch-series | 10.998–77.788 mm |
| Bore position in 4t-inch-series (smallest first) | 23 of 148 |
| Bore above smallest 4t-inch-series size | 15.875 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 2474 | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; brand-specific OEM equivalents (NSK/FAG/NTN) pending multi-source data. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 2474-2420 model number is decoded
The NTN 2203E inch table prints 4T-2474/2420 at 28.575 mm bore (1.125 in), 68.262 mm cup OD and 22.225 mm assembled T, with a grease limiting speed of 5,700 r/min and an oil ceiling of 7,700 r/min. Reading the designation: 4T-2474/2420 follows the ABMA inch convention — the number before the slash is the cone (inner ring with roller set and cage), the number after the slash is the cup (outer ring), and the pure-numeric inch family lettering ties the pair to its boundary plan. Contact-angle geometry of the pure-numeric inch family gives 4T-2474/2420 its radial/axial load split — at 64/65.5 kN the static rating is about 1.02× C, typical of inch tapered sets proportioned for combined duty. Housing fitment sequence for 4T-2474/2420: press the 2420 cup square into the 68.262 mm seat first, then bring the 2474 cone (on its 28.575 mm shaft) into adjustment — the two references are separate engineering parts that happen to ship as one set. The rollers run with their large ends against the cone's guide rib; lubricant must reach that rib face of 4T-2474/2420, not only the raceway, or the pair smears on the first overloaded start.
Typical equipment & failure modes
Common applications
- agricultural tractor transmission and PTO shafts
- industrial gearboxes built to inch shafting
- construction-equipment pivot and wheel positions
- mining and quarry conveyor drive pulleys
Known failure patterns
- rib-face scoring when the thrust share of the combined load exceeds what the cone rib of this size carries
- cup creep and housing fretting when the cup seat is cut too loose for the rotating load
- flaking on one cone only when a bent shaft loads the O/X pair unevenly
- cage damage from a mounting blow transmitted through the roller complement
- fretting corrosion on a loose cone seat that creeps under rotating load
Selection pitfalls — read before you substitute
- Hub and pinion positions of this 28.575 mm class are adjusted in pairs; verify end play against the axle or gearbox drawing and re-torque after bedding-in instead of trusting the first setting on 4T-2474/2420.
- The pure-numeric inch family at 28.575 mm bore (68.262×22.225 mm assembled) is one of several inch families sharing similar bores; cross-series swaps change OD, T and contact angle, so match the full 2474/2420 reference at purchase.
- An unloaded 4T-2474/2420 near 5,700 r/min lets rollers skid and smear the cone rib; spring-preload lightly loaded high-speed pairs.
- Shaft and housing fillets must clear the ring chamfers of 2474 and 2420; use undercut shoulders so the rings seat on the face, not on a radius.
- Quote the full 2474/2420 pair at ordering: the 2474 cone also ships against sibling cups, and a cup from another reference changes the 22.225 mm assembled width and the rating.
- The 64/65.5 kN ratings here are NTN Ball and Roller Bearings CAT.No.2203E figures for 4T-2474/2420; internal geometry legitimately differs between inch-series makers, so re-verify ratings, adjustment and the exact cone/cup references before substituting another brand on a rated drive.
Frequently asked questions
What are the dimensions and catalogue ratings of NTN 4T-2474/2420?
4T-2474/2420 is an inch-series single-row tapered roller bearing to the ABMA boundary plan: 28.575 mm bore (1.125 in), 68.262 mm outside diameter and 22.225 mm assembled width T (2.687 × 0.875 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 64 kN, C0 65.5 kN, grease limiting speed 5,700 r/min, oil speed 7,700 r/min, mass about 380 g. It is an open, separable cone/cup set with a pressed-steel cage.
Are the cone and cup of 4T-2474/2420 interchangeable separately?
Yes — ABMA inch parts are individually interchangeable: the 2474 cone or the 2420 cup can be replaced by an identical reference from NTN or another ABMA-dimensioned maker. Pairing the cone with a different cup reference is a different catalogue row: OD, assembled T and the 64/65.5 kN ratings change with the cup.
What is the difference between 4T-2474/2420 and a metric ISO 355 tapered bearing?
4T-2474/2420 follows the ABMA inch boundary plan with cone/cup references; ISO 355 bearings use metric dimension-series numbers (302, 322, …). Even where a metric size looks close to 28.575×68.262×22.225 mm, the envelopes and contact angles differ — the two systems are not drop-in interchangeable; check every boundary value before substituting.
What does the 4T prefix on 4T-2474/2420 mean?
4T is NTN's tapered roller bearing quality mark, stamped on cone and cup in the factory. It identifies NTN's 4T programme and is not a dimension or variant code, so interchange lists quote the bare 2474/2420 references; the 4T spelling is retained among this page's search aliases.
Why does 4T-2474/2420 list two speeds, 5,700 and 7,700 r/min?
The lower figure, 5,700 r/min, is the grease-lubricated limiting speed — the mechanical ceiling for the cage, rollers and cone-rib contact. With oil lubrication NTN rates 4T-2474/2420 at 7,700 r/min because oil removes rib-contact heat better. Real limits still depend on pair adjustment, oil flow and cooling.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN 2203E 2026-09-25 on 2026-10-01. Read our editorial & correction policy.