25877-25820 bearing: complete specifications & equivalents
The 25877-25820 is a ANSI ABMA 19.2 radial bearing sized 34.925 x 73.025 x 23.812 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 34.925 mm |
| Outer diameter D | 73.025 mm |
| Width B | 23.812 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel |
| Basic dynamic load rating C | 78.5 kN |
| Basic static load rating C0 | 85 kN |
| Limiting speed (mechanical) | 5300 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 470 g |
| Manufacturer designation | NTN 4T-25877/25820 |
| Standard | ANSI ABMA 19.2 |
| Catalog version | NTN 2203E 2026-09-25 |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN 2203E 2026-09-25) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN 2203E 2026-09-25); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 4t-inch-series range
| Bore d | 1.375 in |
|---|---|
| Outer diameter D | 2.875 in |
| Width B | 0.937 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 19.1 mm |
| Smallest bore in 4t-inch-series | 12.7 mm |
| Largest outer diameter in 4t-inch-series | 260 mm |
| Width range across 4t-inch-series | 10.998–77.788 mm |
| Bore position in 4t-inch-series (smallest first) | 34 of 148 |
| Bore above smallest 4t-inch-series size | 22.224999999999998 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 25877-25821-NTN | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same NTN cone 4T-25877 paired with a different cup (25821): cone interchangeable, cup differs — OD, assembled width T and ratings follow the cup. Verify the full cone/cup reference before substituting. |
| 25877-25821 | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 34.925×73.025×23.812 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 25877-25820 model number is decoded
NTN supplies this 1.375 in (34.925 mm) shaft position as 4T-25877/25820: cone 25877, cup 25820, profiled rollers and a pressed-steel cage, rated 78.5 kN basic dynamic and 85 kN static. Letter prefixes inherited from the inch convention mark the load family: LM reads as light-medium, HM as heavy-medium, LL as extra-light, J-prefixed codes as metric-envelope families — 25877 sits in the pure-numeric inch family. Selection: C 78.5 kN against C0 85 kN gives a C0/C ratio of 1.08 for the 34.925 mm bore; the pair is counted as one adjusted unit when checking L10 at the equivalent combined load. The printed 78.5/85 kN ratings belong to the assembled 25877+25820 pair; a sibling row using the same cone with a different cup carries its own rating row because the raceway track shifts with the cup. Contact-pattern check with marking blue: a pattern biased to one roller end means the 34.925 mm pair is misadjusted and the set will edge-load in service.
Typical equipment & failure modes
Common applications
- industrial gearboxes built to inch shafting
- construction-equipment pivot and wheel positions
- mining and quarry conveyor drive pulleys
- machine-tool headstocks on inch spindles
Known failure patterns
- rib-face scoring when the thrust share of the combined load exceeds what the cone rib of this size carries
- cup creep and housing fretting when the cup seat is cut too loose for the rotating load
- flaking on one cone only when a bent shaft loads the O/X pair unevenly
- pressed-steel cage pocket wear from roller skid at light radial load and high speed
- indentation of the raceways by hard particles in an open, unsealed arrangement
Selection pitfalls — read before you substitute
- Hub and pinion positions of this 34.925 mm class are adjusted in pairs; verify end play against the axle or gearbox drawing and re-torque after bedding-in instead of trusting the first setting on 4T-25877/25820.
- The pure-numeric inch family at 34.925 mm bore (73.025×23.812 mm assembled) is one of several inch families sharing similar bores; cross-series swaps change OD, T and contact angle, so match the full 25877/25820 reference at purchase.
- Do not confuse T (23.812 mm, the assembled cone-plus-cup width) with the cone width when drawing spacers; an abutment sized to T leaves the cup unseated.
- Quote the full 25877/25820 pair at ordering: the 25877 cone also ships against sibling cups, and a cup from another reference changes the 23.812 mm assembled width and the rating.
- Do not confuse T (23.812 mm, the assembled cone-plus-cup width) with the cone width when drawing spacers; an abutment sized to T leaves the cup unseated.
- The 78.5/85 kN ratings here are NTN Ball and Roller Bearings CAT.No.2203E figures for 4T-25877/25820; internal geometry legitimately differs between inch-series makers, so re-verify ratings, adjustment and the exact cone/cup references before substituting another brand on a rated drive.
Frequently asked questions
What are the dimensions and catalogue ratings of NTN 4T-25877/25820?
4T-25877/25820 is an inch-series single-row tapered roller bearing to the ABMA boundary plan: 34.925 mm bore (1.375 in), 73.025 mm outside diameter and 23.812 mm assembled width T (2.875 × 0.937 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 78.5 kN, C0 85 kN, grease limiting speed 5,300 r/min, oil speed 7,100 r/min, mass about 470 g. It is an open, separable cone/cup set with a pressed-steel cage.
Are the cone and cup of 4T-25877/25820 interchangeable separately?
Yes — ABMA inch parts are individually interchangeable: the 25877 cone or the 25820 cup can be replaced by an identical reference from NTN or another ABMA-dimensioned maker. Pairing the cone with a different cup reference is a different catalogue row: OD, assembled T and the 78.5/85 kN ratings change with the cup.
What is the difference between 4T-25877/25820 and a metric ISO 355 tapered bearing?
4T-25877/25820 follows the ABMA inch boundary plan with cone/cup references; ISO 355 bearings use metric dimension-series numbers (302, 322, …). Even where a metric size looks close to 34.925×73.025×23.812 mm, the envelopes and contact angles differ — the two systems are not drop-in interchangeable; check every boundary value before substituting.
What does the 4T prefix on 4T-25877/25820 mean?
4T is NTN's tapered roller bearing quality mark, stamped on cone and cup in the factory. It identifies NTN's 4T programme and is not a dimension or variant code, so interchange lists quote the bare 25877/25820 references; the 4T spelling is retained among this page's search aliases.
Why does 4T-25877/25820 list two speeds, 5,300 and 7,100 r/min?
The lower figure, 5,300 r/min, is the grease-lubricated limiting speed — the mechanical ceiling for the cage, rollers and cone-rib contact. With oil lubrication NTN rates 4T-25877/25820 at 7,100 r/min because oil removes rib-contact heat better. Real limits still depend on pair adjustment, oil flow and cooling.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN 2203E 2026-09-25 on 2026-10-01. Read our editorial & correction policy.