28584-28521 bearing: complete specifications & equivalents
The 28584-28521 is a ANSI ABMA 19.2 radial bearing sized 52.388 x 92.075 x 24.608 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 52.388 mm |
| Outer diameter D | 92.075 mm |
| Width B | 24.608 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel |
| Basic dynamic load rating C | 93 kN |
| Basic static load rating C0 | 116 kN |
| Limiting speed (mechanical) | 4000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 703 g |
| Manufacturer designation | NTN 4T-28584/28521 |
| Standard | ANSI ABMA 19.2 |
| Catalog version | NTN 2203E 2026-09-25 |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN 2203E 2026-09-25) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN 2203E 2026-09-25); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 4t-inch-series range
| Bore d | 2.063 in |
|---|---|
| Outer diameter D | 3.625 in |
| Width B | 0.969 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 19.8 mm |
| Smallest bore in 4t-inch-series | 12.7 mm |
| Largest outer diameter in 4t-inch-series | 260 mm |
| Width range across 4t-inch-series | 10.998–77.788 mm |
| Bore position in 4t-inch-series (smallest first) | 66 of 148 |
| Bore above smallest 4t-inch-series size | 39.688 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 28584 | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; brand-specific OEM equivalents (NSK/FAG/NTN) pending multi-source data. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 28584-28521 model number is decoded
The NTN 2203E inch table prints 4T-28584/28521 at 52.388 mm bore (2.063 in), 92.075 mm cup OD and 24.608 mm assembled T, with a grease limiting speed of 4,000 r/min and an oil ceiling of 5,300 r/min. Reading the designation: 4T-28584/28521 follows the ABMA inch convention — the number before the slash is the cone (inner ring with roller set and cage), the number after the slash is the cup (outer ring), and the pure-numeric inch family lettering ties the pair to its boundary plan. Imperial cross-check for the drawing: 52.388×92.075×24.608 mm converts to 2.063 × 3.625 × 0.969 in; the ABMA envelope swaps with like-numbered inch parts but the 93/116 kN ratings are NTN-specific. Cup-side note for 28521: within the pure-numeric inch family tables the 28584 cone is listed against several cup options, and it is the cup that fixes the 92.075 mm OD and the 24.608 mm assembled width — quote the full 28584/28521 pair, never the cone alone. A single-row tapered bearing reacts thrust in one direction only; 4T-28584/28521 is adjusted against a second bearing so the shaft is located in both directions.
Typical equipment & failure modes
Common applications
- truck and trailer axle hubs on inch-dimensioned axles
- agricultural tractor transmission and PTO shafts
- industrial gearboxes built to inch shafting
- construction-equipment pivot and wheel positions
Known failure patterns
- cone-rib and roller large-end smearing when the adjusted pair runs with preload but starved lubricant film
- false brinelling on a stationary pair exposed to vibration during transport or standby
- preload loss and noise after one bearing of the adjusted pair is replaced without resetting end play
- cage damage from a mounting blow transmitted through the roller complement
- brinell marks on cone and cup raceways from impact during handling or hammer fitting
Selection pitfalls — read before you substitute
- Hub and pinion positions of this 52.388 mm class are adjusted in pairs; verify end play against the axle or gearbox drawing and re-torque after bedding-in instead of trusting the first setting on 4T-28584/28521.
- The pure-numeric inch family at 52.388 mm bore (92.075×24.608 mm assembled) is one of several inch families sharing similar bores; cross-series swaps change OD, T and contact angle, so match the full 28584/28521 reference at purchase.
- Replacing one half of an adjusted pair without resetting end play negates the 24.608 mm T logic: re-adjust the set and re-verify the contact pattern rather than reusing the old spacer stack.
- Fit selection follows the rotating ring: a rotating cone on a 52.388 mm shaft takes a k5/m5 seat, and a rotating cup reverses the logic — decide from the load diagram, not from habit.
- Grease packs must leave free volume inside the 24.608 mm-wide set; over-greasing a pair churning near the oil-band speed of 5,300 r/min raises temperature and destroys the setting.
- The 93/116 kN ratings here are NTN Ball and Roller Bearings CAT.No.2203E figures for 4T-28584/28521; internal geometry legitimately differs between inch-series makers, so re-verify ratings, adjustment and the exact cone/cup references before substituting another brand on a rated drive.
Frequently asked questions
What are the dimensions and catalogue ratings of NTN 4T-28584/28521?
4T-28584/28521 is an inch-series single-row tapered roller bearing to the ABMA boundary plan: 52.388 mm bore (2.063 in), 92.075 mm outside diameter and 24.608 mm assembled width T (3.625 × 0.969 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 93 kN, C0 116 kN, grease limiting speed 4,000 r/min, oil speed 5,300 r/min, mass about 703 g. It is an open, separable cone/cup set with a pressed-steel cage.
Are the cone and cup of 4T-28584/28521 interchangeable separately?
Yes — ABMA inch parts are individually interchangeable: the 28584 cone or the 28521 cup can be replaced by an identical reference from NTN or another ABMA-dimensioned maker. Pairing the cone with a different cup reference is a different catalogue row: OD, assembled T and the 93/116 kN ratings change with the cup.
What is the difference between 4T-28584/28521 and a metric ISO 355 tapered bearing?
4T-28584/28521 follows the ABMA inch boundary plan with cone/cup references; ISO 355 bearings use metric dimension-series numbers (302, 322, …). Even where a metric size looks close to 52.388×92.075×24.608 mm, the envelopes and contact angles differ — the two systems are not drop-in interchangeable; check every boundary value before substituting.
What does the 4T prefix on 4T-28584/28521 mean?
4T is NTN's tapered roller bearing quality mark, stamped on cone and cup in the factory. It identifies NTN's 4T programme and is not a dimension or variant code, so interchange lists quote the bare 28584/28521 references; the 4T spelling is retained among this page's search aliases.
Why does 4T-28584/28521 list two speeds, 4,000 and 5,300 r/min?
The lower figure, 4,000 r/min, is the grease-lubricated limiting speed — the mechanical ceiling for the cage, rollers and cone-rib contact. With oil lubrication NTN rates 4T-28584/28521 at 5,300 r/min because oil removes rib-contact heat better. Real limits still depend on pair adjustment, oil flow and cooling.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN 2203E 2026-09-25 on 2026-10-01. Read our editorial & correction policy.