29580-29520 bearing: complete specifications & equivalents
The 29580-29520 is a ANSI ABMA 19.2 radial bearing sized 60 x 107.95 x 25.4 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 60 mm |
| Outer diameter D | 107.95 mm |
| Width B | 25.4 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel |
| Basic dynamic load rating C | 101 kN |
| Basic static load rating C0 | 140 kN |
| Limiting speed (mechanical) | 3200 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 992 g |
| Manufacturer designation | NTN 4T-29580/29520 |
| Standard | ANSI ABMA 19.2 |
| Catalog version | NTN 2203E 2026-09-25 |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN 2203E 2026-09-25) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN 2203E 2026-09-25); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 4t-inch-series range
| Bore d | 2.362 in |
|---|---|
| Outer diameter D | 4.25 in |
| Width B | 1 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 24 mm |
| Smallest bore in 4t-inch-series | 12.7 mm |
| Largest outer diameter in 4t-inch-series | 260 mm |
| Width range across 4t-inch-series | 10.998–77.788 mm |
| Bore position in 4t-inch-series (smallest first) | 76 of 148 |
| Bore above smallest 4t-inch-series size | 47.3 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 29580 | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; brand-specific OEM equivalents (NSK/FAG/NTN) pending multi-source data. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 29580-29520 model number is decoded
For an inch shaft of 60 mm carrying combined radial and thrust load, NTN lists 4T-29580/29520, a single-row 4T tapered roller set of 101 kN C and 140 kN C0 inside the 107.95 mm OD cup. Unlike ISO 355 metric numbers, this ABMA code does not encode the bore arithmetically: 29580 identifies the cone of 60 mm (2.362 in) bore by catalogue lookup, and 29520 fixes the 107.95 mm OD. Two single-row inch sets are normally mounted as an adjusted O or X pair; the 25.4 mm T of each 4T-29580/29520 enters the spacer calculation, so the tolerance on assembled width matters as much as the bore fit. The printed 101/140 kN ratings belong to the assembled 29580+29520 pair; a sibling row using the same cone with a different cup carries its own rating row because the raceway track shifts with the cup. Contact-pattern check with marking blue: a pattern biased to one roller end means the 60 mm pair is misadjusted and the set will edge-load in service.
Typical equipment & failure modes
Common applications
- paper-machine and calender roll supports
- off-highway and forestry machine axles
- marine winch and deck-machinery shafts
- crusher and screening-plant eccentric shafts
Known failure patterns
- rib-face scoring when the thrust share of the combined load exceeds what the cone rib of this size carries
- false brinelling on a stationary pair exposed to vibration during transport or standby
- preload loss and noise after one bearing of the adjusted pair is replaced without resetting end play
- cage damage from a mounting blow transmitted through the roller complement
- indentation of the raceways by hard particles in an open, unsealed arrangement
Selection pitfalls — read before you substitute
- Mount the 60 mm cone by induction heating (max 120 °C) and the 107.95 mm cup with a press sleeve; at 992 g a cocked ring brinells the raceway directly.
- The pure-numeric inch family at 60 mm bore (107.95×25.4 mm assembled) is one of several inch families sharing similar bores; cross-series swaps change OD, T and contact angle, so match the full 29580/29520 reference at purchase.
- Fit selection follows the rotating ring: a rotating cone on a 60 mm shaft takes a k5/m5 seat, and a rotating cup reverses the logic — decide from the load diagram, not from habit.
- Fit selection follows the rotating ring: a rotating cone on a 60 mm shaft takes a k5/m5 seat, and a rotating cup reverses the logic — decide from the load diagram, not from habit.
- Inch and metric bores collide on paper — 60 mm is 2.362 in, not a round metric size; a metric bearing that seems 0.1 mm off will not seat on the inch shaft.
- The 101/140 kN ratings here are NTN Ball and Roller Bearings CAT.No.2203E figures for 4T-29580/29520; internal geometry legitimately differs between inch-series makers, so re-verify ratings, adjustment and the exact cone/cup references before substituting another brand on a rated drive.
Frequently asked questions
What are the dimensions and catalogue ratings of NTN 4T-29580/29520?
4T-29580/29520 is an inch-series single-row tapered roller bearing to the ABMA boundary plan: 60 mm bore (2.362 in), 107.95 mm outside diameter and 25.4 mm assembled width T (4.25 × 1 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 101 kN, C0 140 kN, grease limiting speed 3,200 r/min, oil speed 4,300 r/min, mass about 992 g. It is an open, separable cone/cup set with a pressed-steel cage.
Are the cone and cup of 4T-29580/29520 interchangeable separately?
Yes — ABMA inch parts are individually interchangeable: the 29580 cone or the 29520 cup can be replaced by an identical reference from NTN or another ABMA-dimensioned maker. Pairing the cone with a different cup reference is a different catalogue row: OD, assembled T and the 101/140 kN ratings change with the cup.
What is the difference between 4T-29580/29520 and a metric ISO 355 tapered bearing?
4T-29580/29520 follows the ABMA inch boundary plan with cone/cup references; ISO 355 bearings use metric dimension-series numbers (302, 322, …). Even where a metric size looks close to 60×107.95×25.4 mm, the envelopes and contact angles differ — the two systems are not drop-in interchangeable; check every boundary value before substituting.
What does the 4T prefix on 4T-29580/29520 mean?
4T is NTN's tapered roller bearing quality mark, stamped on cone and cup in the factory. It identifies NTN's 4T programme and is not a dimension or variant code, so interchange lists quote the bare 29580/29520 references; the 4T spelling is retained among this page's search aliases.
Why does 4T-29580/29520 list two speeds, 3,200 and 4,300 r/min?
The lower figure, 3,200 r/min, is the grease-lubricated limiting speed — the mechanical ceiling for the cage, rollers and cone-rib contact. With oil lubrication NTN rates 4T-29580/29520 at 4,300 r/min because oil removes rib-contact heat better. Real limits still depend on pair adjustment, oil flow and cooling.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN 2203E 2026-09-25 on 2026-10-01. Read our editorial & correction policy.