34306-34478-NTN bearing: complete specifications & equivalents
The 34306-34478-NTN is a ANSI ABMA 19.2 radial bearing sized 77.788 x 121.442 x 24.608 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 77.788 mm |
| Outer diameter D | 121.442 mm |
| Width B | 24.608 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel |
| Basic dynamic load rating C | 101 kN |
| Basic static load rating C0 | 127 kN |
| Limiting speed (mechanical) | 2900 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 940 g |
| Manufacturer designation | NTN 4T-34306/34478 |
| Standard | ANSI ABMA 19.2 |
| Catalog version | NTN 2203E 2026-09-25 |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN 2203E 2026-09-25) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN 2203E 2026-09-25); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 4t-inch-series range
| Bore d | 3.063 in |
|---|---|
| Outer diameter D | 4.781 in |
| Width B | 0.969 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 21.8 mm |
| Smallest bore in 4t-inch-series | 12.7 mm |
| Largest outer diameter in 4t-inch-series | 260 mm |
| Width range across 4t-inch-series | 10.998–77.788 mm |
| Bore position in 4t-inch-series (smallest first) | 95 of 148 |
| Bore above smallest 4t-inch-series size | 65.088 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 34306-34478 | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 77.788×121.442×24.608 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 34306-34478-NTN model number is decoded
The NTN 2203E inch table prints 4T-34306/34478 at 77.788 mm bore (3.063 in), 121.442 mm cup OD and 24.608 mm assembled T, with a grease limiting speed of 2,900 r/min and an oil ceiling of 3,800 r/min. The 4T prefix is NTN's tapered roller quality mark stamped on both parts; it is a brand mark, not a size code, so cross-references quote 34306/34478 without it. Selection: C 101 kN against C0 127 kN gives a C0/C ratio of 1.26 for the 77.788 mm bore; the pair is counted as one adjusted unit when checking L10 at the equivalent combined load. Housing fitment sequence for 4T-34306/34478: press the 34478 cup square into the 121.442 mm seat first, then bring the 34306 cone (on its 77.788 mm shaft) into adjustment — the two references are separate engineering parts that happen to ship as one set. Mount the 77.788 mm cone with an induction heater (max 120 °C) and press the 121.442 mm cup with a sleeve; driving either ring through the rollers brinells the raceways.
Typical equipment & failure modes
Common applications
- heavy truck and bus drive-axle differentials
- plant gearboxes on inch-dimensioned shaft lines
- large conveyor head pulleys in bulk-handling plant
- paper-machine and calender roll supports
Known failure patterns
- cone-rib and roller large-end smearing when the adjusted pair runs with preload but starved lubricant film
- preload loss and noise after one bearing of the adjusted pair is replaced without resetting end play
- false brinelling on a stationary pair exposed to vibration during transport or standby
- cage fatigue when the pair runs continuously near the grease limiting speed without oil cooling
- fretting corrosion on a loose cone seat that creeps under rotating load
Selection pitfalls — read before you substitute
- Mount the 77.788 mm cone by induction heating (max 120 °C) and the 121.442 mm cup with a press sleeve; at 940 g a cocked ring brinells the raceway directly.
- The pure-numeric inch family at 77.788 mm bore (121.442×24.608 mm assembled) is one of several inch families sharing similar bores; cross-series swaps change OD, T and contact angle, so match the full 34306/34478 reference at purchase.
- Quote the full 34306/34478 pair at ordering: the 34306 cone also ships against sibling cups, and a cup from another reference changes the 24.608 mm assembled width and the rating.
- Open 4T-34306/34478 sets have no seals: a hub or gearbox needs external sealing or the 2,900 r/min grease figure is meaningless once water reaches the cone rib.
- Replacing one half of an adjusted pair without resetting end play negates the 24.608 mm T logic: re-adjust the set and re-verify the contact pattern rather than reusing the old spacer stack.
- The 101/127 kN ratings here are NTN Ball and Roller Bearings CAT.No.2203E figures for 4T-34306/34478; internal geometry legitimately differs between inch-series makers, so re-verify ratings, adjustment and the exact cone/cup references before substituting another brand on a rated drive.
Frequently asked questions
What are the dimensions and catalogue ratings of NTN 4T-34306/34478?
4T-34306/34478 is an inch-series single-row tapered roller bearing to the ABMA boundary plan: 77.788 mm bore (3.063 in), 121.442 mm outside diameter and 24.608 mm assembled width T (4.781 × 0.969 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 101 kN, C0 127 kN, grease limiting speed 2,900 r/min, oil speed 3,800 r/min, mass about 940 g. It is an open, separable cone/cup set with a pressed-steel cage.
Are the cone and cup of 4T-34306/34478 interchangeable separately?
Yes — ABMA inch parts are individually interchangeable: the 34306 cone or the 34478 cup can be replaced by an identical reference from NTN or another ABMA-dimensioned maker. Pairing the cone with a different cup reference is a different catalogue row: OD, assembled T and the 101/127 kN ratings change with the cup.
What is the difference between 4T-34306/34478 and a metric ISO 355 tapered bearing?
4T-34306/34478 follows the ABMA inch boundary plan with cone/cup references; ISO 355 bearings use metric dimension-series numbers (302, 322, …). Even where a metric size looks close to 77.788×121.442×24.608 mm, the envelopes and contact angles differ — the two systems are not drop-in interchangeable; check every boundary value before substituting.
What does the 4T prefix on 4T-34306/34478 mean?
4T is NTN's tapered roller bearing quality mark, stamped on cone and cup in the factory. It identifies NTN's 4T programme and is not a dimension or variant code, so interchange lists quote the bare 34306/34478 references; the 4T spelling is retained among this page's search aliases.
Why does 4T-34306/34478 list two speeds, 2,900 and 3,800 r/min?
The lower figure, 2,900 r/min, is the grease-lubricated limiting speed — the mechanical ceiling for the cage, rollers and cone-rib contact. With oil lubrication NTN rates 4T-34306/34478 at 3,800 r/min because oil removes rib-contact heat better. Real limits still depend on pair adjustment, oil flow and cooling.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN 2203E 2026-09-25 on 2026-10-01. Read our editorial & correction policy.