3872-3820 bearing: complete specifications & equivalents
The 3872-3820 is a ANSI ABMA 19.2 radial bearing sized 34.925 x 85.725 x 30.162 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 34.925 mm |
| Outer diameter D | 85.725 mm |
| Width B | 30.162 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel |
| Basic dynamic load rating C | 116 kN |
| Basic static load rating C0 | 132 kN |
| Limiting speed (mechanical) | 4500 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 902 g |
| Manufacturer designation | NTN 4T-3872/3820 |
| Standard | ANSI ABMA 19.2 |
| Catalog version | NTN 2203E 2026-09-25 |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN 2203E 2026-09-25) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN 2203E 2026-09-25); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 4t-inch-series range
| Bore d | 1.375 in |
|---|---|
| Outer diameter D | 3.375 in |
| Width B | 1.187 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 25.4 mm |
| Smallest bore in 4t-inch-series | 12.7 mm |
| Largest outer diameter in 4t-inch-series | 260 mm |
| Width range across 4t-inch-series | 10.998–77.788 mm |
| Bore position in 4t-inch-series (smallest first) | 34 of 148 |
| Bore above smallest 4t-inch-series size | 22.224999999999998 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 3872 | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; brand-specific OEM equivalents (NSK/FAG/NTN) pending multi-source data. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 3872-3820 model number is decoded
4T-3872/3820 belongs to the NTN inch 4T tapered roller range (pure-numeric inch family); cone and cup are ordered by their own references and are individually interchangeable with like-numbered parts. Cone and cup of 4T-3872/3820 are separately stocked parts: a worn 3820 cup can be replaced against the existing 3872 cone, provided the new cup carries the identical reference — pairing across references changes the 30.162 mm assembled width and the rating. Speed planning uses both catalogue columns: grease 4,500 r/min is the mechanical ceiling for 4T-3872/3820, oil 6,000 r/min with circulating oil — a 1,500 r/min margin at this size. Cup-side note for 3820: within the pure-numeric inch family tables the 3872 cone is listed against several cup options, and it is the cup that fixes the 85.725 mm OD and the 30.162 mm assembled width — quote the full 3872/3820 pair, never the cone alone. Fillet radii must clear the chamfers of the 3872 cone and 3820 cup; undercut shoulders seat the rings fully instead of bridging on a radius.
Typical equipment & failure modes
Common applications
- agricultural tractor transmission and PTO shafts
- industrial gearboxes built to inch shafting
- construction-equipment pivot and wheel positions
- mining and quarry conveyor drive pulleys
Known failure patterns
- cone-rib and roller large-end smearing when the adjusted pair runs with preload but starved lubricant film
- preload loss and noise after one bearing of the adjusted pair is replaced without resetting end play
- false brinelling on a stationary pair exposed to vibration during transport or standby
- cage damage from a mounting blow transmitted through the roller complement
- rolling-contact fatigue spalling after the catalogue L10 life at the actual combined load
Selection pitfalls — read before you substitute
- Hub and pinion positions of this 34.925 mm class are adjusted in pairs; verify end play against the axle or gearbox drawing and re-torque after bedding-in instead of trusting the first setting on 4T-3872/3820.
- The pure-numeric inch family at 34.925 mm bore (85.725×30.162 mm assembled) is one of several inch families sharing similar bores; cross-series swaps change OD, T and contact angle, so match the full 3872/3820 reference at purchase.
- Fit selection follows the rotating ring: a rotating cone on a 34.925 mm shaft takes a k5/m5 seat, and a rotating cup reverses the logic — decide from the load diagram, not from habit.
- Never drive the 85.725 mm cup home through the rollers: fitting force goes through the ring faces only, or brinell marks release as noise within the first running hours.
- Do not confuse T (30.162 mm, the assembled cone-plus-cup width) with the cone width when drawing spacers; an abutment sized to T leaves the cup unseated.
- The 116/132 kN ratings here are NTN Ball and Roller Bearings CAT.No.2203E figures for 4T-3872/3820; internal geometry legitimately differs between inch-series makers, so re-verify ratings, adjustment and the exact cone/cup references before substituting another brand on a rated drive.
Frequently asked questions
What are the dimensions and catalogue ratings of NTN 4T-3872/3820?
4T-3872/3820 is an inch-series single-row tapered roller bearing to the ABMA boundary plan: 34.925 mm bore (1.375 in), 85.725 mm outside diameter and 30.162 mm assembled width T (3.375 × 1.187 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 116 kN, C0 132 kN, grease limiting speed 4,500 r/min, oil speed 6,000 r/min, mass about 902 g. It is an open, separable cone/cup set with a pressed-steel cage.
Are the cone and cup of 4T-3872/3820 interchangeable separately?
Yes — ABMA inch parts are individually interchangeable: the 3872 cone or the 3820 cup can be replaced by an identical reference from NTN or another ABMA-dimensioned maker. Pairing the cone with a different cup reference is a different catalogue row: OD, assembled T and the 116/132 kN ratings change with the cup.
What is the difference between 4T-3872/3820 and a metric ISO 355 tapered bearing?
4T-3872/3820 follows the ABMA inch boundary plan with cone/cup references; ISO 355 bearings use metric dimension-series numbers (302, 322, …). Even where a metric size looks close to 34.925×85.725×30.162 mm, the envelopes and contact angles differ — the two systems are not drop-in interchangeable; check every boundary value before substituting.
What does the 4T prefix on 4T-3872/3820 mean?
4T is NTN's tapered roller bearing quality mark, stamped on cone and cup in the factory. It identifies NTN's 4T programme and is not a dimension or variant code, so interchange lists quote the bare 3872/3820 references; the 4T spelling is retained among this page's search aliases.
Why does 4T-3872/3820 list two speeds, 4,500 and 6,000 r/min?
The lower figure, 4,500 r/min, is the grease-lubricated limiting speed — the mechanical ceiling for the cage, rollers and cone-rib contact. With oil lubrication NTN rates 4T-3872/3820 at 6,000 r/min because oil removes rib-contact heat better. Real limits still depend on pair adjustment, oil flow and cooling.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN 2203E 2026-09-25 on 2026-10-01. Read our editorial & correction policy.