3982-3920-NTN bearing: complete specifications & equivalents
The 3982-3920-NTN is a ANSI ABMA 19.2 radial bearing sized 63.5 x 112.712 x 30.162 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 63.5 mm |
| Outer diameter D | 112.712 mm |
| Width B | 30.162 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel |
| Basic dynamic load rating C | 132 kN |
| Basic static load rating C0 | 174 kN |
| Limiting speed (mechanical) | 3200 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 1270 g |
| Manufacturer designation | NTN 4T-3982/3920 |
| Standard | ANSI ABMA 19.2 |
| Catalog version | NTN 2203E 2026-09-25 |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN 2203E 2026-09-25) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN 2203E 2026-09-25); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 4t-inch-series range
| Bore d | 2.5 in |
|---|---|
| Outer diameter D | 4.437 in |
| Width B | 1.187 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 24.6 mm |
| Smallest bore in 4t-inch-series | 12.7 mm |
| Largest outer diameter in 4t-inch-series | 260 mm |
| Width range across 4t-inch-series | 10.998–77.788 mm |
| Bore position in 4t-inch-series (smallest first) | 81 of 148 |
| Bore above smallest 4t-inch-series size | 50.8 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 3982-3920 | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 63.5×112.712×30.162 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 3982-3920-NTN model number is decoded
4T-3982/3920 is an NTN inch-series single-row tapered roller bearing: a separable cone-and-cup pair on the ABMA inch boundary plan, 63.5×112.712×30.162 mm (assembled width T), for a shaft of about 63.5 mm (2.5 in). Cone and cup of 4T-3982/3920 are separately stocked parts: a worn 3920 cup can be replaced against the existing 3982 cone, provided the new cup carries the identical reference — pairing across references changes the 30.162 mm assembled width and the rating. The 24.6 mm radial section over the 63.5 mm bore positions the contact line of the pair; abutment shoulders and spacers are dimensioned from that geometry, not from the bore alone. The printed 132/174 kN ratings belong to the assembled 3982+3920 pair; a sibling row using the same cone with a different cup carries its own rating row because the raceway track shifts with the cup. Minimum load matters at speed: an unloaded 4T-3982/3920 run near 3,200 r/min lets the rollers skid; lightly spring-preload high-speed pair arrangements.
Typical equipment & failure modes
Common applications
- plant gearboxes on inch-dimensioned shaft lines
- large conveyor head pulleys in bulk-handling plant
- paper-machine and calender roll supports
- off-highway and forestry machine axles
Known failure patterns
- cone-rib and roller large-end smearing when the adjusted pair runs with preload but starved lubricant film
- false brinelling on a stationary pair exposed to vibration during transport or standby
- preload loss and noise after one bearing of the adjusted pair is replaced without resetting end play
- cage fatigue when the pair runs continuously near the grease limiting speed without oil cooling
- indentation of the raceways by hard particles in an open, unsealed arrangement
Selection pitfalls — read before you substitute
- Mount the 63.5 mm cone by induction heating (max 120 °C) and the 112.712 mm cup with a press sleeve; at 1270 g a cocked ring brinells the raceway directly.
- The pure-numeric inch family at 63.5 mm bore (112.712×30.162 mm assembled) is one of several inch families sharing similar bores; cross-series swaps change OD, T and contact angle, so match the full 3982/3920 reference at purchase.
- Grease packs must leave free volume inside the 30.162 mm-wide set; over-greasing a pair churning near the oil-band speed of 4,300 r/min raises temperature and destroys the setting.
- An unloaded 4T-3982/3920 near 3,200 r/min lets rollers skid and smear the cone rib; spring-preload lightly loaded high-speed pairs.
- Do not confuse T (30.162 mm, the assembled cone-plus-cup width) with the cone width when drawing spacers; an abutment sized to T leaves the cup unseated.
- The 132/174 kN ratings here are NTN Ball and Roller Bearings CAT.No.2203E figures for 4T-3982/3920; internal geometry legitimately differs between inch-series makers, so re-verify ratings, adjustment and the exact cone/cup references before substituting another brand on a rated drive.
Frequently asked questions
What are the dimensions and catalogue ratings of NTN 4T-3982/3920?
4T-3982/3920 is an inch-series single-row tapered roller bearing to the ABMA boundary plan: 63.5 mm bore (2.5 in), 112.712 mm outside diameter and 30.162 mm assembled width T (4.437 × 1.187 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 132 kN, C0 174 kN, grease limiting speed 3,200 r/min, oil speed 4,300 r/min, mass about 1270 g. It is an open, separable cone/cup set with a pressed-steel cage.
Are the cone and cup of 4T-3982/3920 interchangeable separately?
Yes — ABMA inch parts are individually interchangeable: the 3982 cone or the 3920 cup can be replaced by an identical reference from NTN or another ABMA-dimensioned maker. Pairing the cone with a different cup reference is a different catalogue row: OD, assembled T and the 132/174 kN ratings change with the cup.
What is the difference between 4T-3982/3920 and a metric ISO 355 tapered bearing?
4T-3982/3920 follows the ABMA inch boundary plan with cone/cup references; ISO 355 bearings use metric dimension-series numbers (302, 322, …). Even where a metric size looks close to 63.5×112.712×30.162 mm, the envelopes and contact angles differ — the two systems are not drop-in interchangeable; check every boundary value before substituting.
What does the 4T prefix on 4T-3982/3920 mean?
4T is NTN's tapered roller bearing quality mark, stamped on cone and cup in the factory. It identifies NTN's 4T programme and is not a dimension or variant code, so interchange lists quote the bare 3982/3920 references; the 4T spelling is retained among this page's search aliases.
Why does 4T-3982/3920 list two speeds, 3,200 and 4,300 r/min?
The lower figure, 3,200 r/min, is the grease-lubricated limiting speed — the mechanical ceiling for the cage, rollers and cone-rib contact. With oil lubrication NTN rates 4T-3982/3920 at 4,300 r/min because oil removes rib-contact heat better. Real limits still depend on pair adjustment, oil flow and cooling.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN 2203E 2026-09-25 on 2026-10-01. Read our editorial & correction policy.