42350-42584 bearing: complete specifications & equivalents
The 42350-42584 is a ANSI ABMA 19.2 radial bearing sized 88.9 x 148.43 x 28.575 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 88.9 mm |
| Outer diameter D | 148.43 mm |
| Width B | 28.575 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel |
| Basic dynamic load rating C | 153 kN |
| Basic static load rating C0 | 215 kN |
| Limiting speed (mechanical) | 2300 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 1950 g |
| Manufacturer designation | NTN 4T-42350/42584 |
| Standard | ANSI ABMA 19.2 |
| Catalog version | NTN 2203E 2026-09-25 |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN 2203E 2026-09-25) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN 2203E 2026-09-25); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 4t-inch-series range
| Bore d | 3.5 in |
|---|---|
| Outer diameter D | 5.844 in |
| Width B | 1.125 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 29.8 mm |
| Smallest bore in 4t-inch-series | 12.7 mm |
| Largest outer diameter in 4t-inch-series | 260 mm |
| Width range across 4t-inch-series | 10.998–77.788 mm |
| Bore position in 4t-inch-series (smallest first) | 106 of 148 |
| Bore above smallest 4t-inch-series size | 76.2 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 42350 | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; brand-specific OEM equivalents (NSK/FAG/NTN) pending multi-source data. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 42350-42584 model number is decoded
NTN supplies this 3.5 in (88.9 mm) shaft position as 4T-42350/42584: cone 42350, cup 42584, profiled rollers and a pressed-steel cage, rated 153 kN basic dynamic and 215 kN static. Letter prefixes inherited from the inch convention mark the load family: LM reads as light-medium, HM as heavy-medium, LL as extra-light, J-prefixed codes as metric-envelope families — 42350 sits in the pure-numeric inch family. Two single-row inch sets are normally mounted as an adjusted O or X pair; the 28.575 mm T of each 4T-42350/42584 enters the spacer calculation, so the tolerance on assembled width matters as much as the bore fit. The printed 153/215 kN ratings belong to the assembled 42350+42584 pair; a sibling row using the same cone with a different cup carries its own rating row because the raceway track shifts with the cup. Contact-pattern check with marking blue: a pattern biased to one roller end means the 88.9 mm pair is misadjusted and the set will edge-load in service.
Typical equipment & failure modes
Common applications
- crusher and screening-plant eccentric shafts
- heavy truck and bus drive-axle differentials
- plant gearboxes on inch-dimensioned shaft lines
- large conveyor head pulleys in bulk-handling plant
Known failure patterns
- rib-face scoring when the thrust share of the combined load exceeds what the cone rib of this size carries
- flaking on one cone only when a bent shaft loads the O/X pair unevenly
- cup creep and housing fretting when the cup seat is cut too loose for the rotating load
- pressed-steel cage pocket wear from roller skid at light radial load and high speed
- indentation of the raceways by hard particles in an open, unsealed arrangement
Selection pitfalls — read before you substitute
- Mount the 88.9 mm cone by induction heating (max 120 °C) and the 148.43 mm cup with a press sleeve; at 1950 g a cocked ring brinells the raceway directly.
- The pure-numeric inch family at 88.9 mm bore (148.43×28.575 mm assembled) is one of several inch families sharing similar bores; cross-series swaps change OD, T and contact angle, so match the full 42350/42584 reference at purchase.
- Fit selection follows the rotating ring: a rotating cone on a 88.9 mm shaft takes a k5/m5 seat, and a rotating cup reverses the logic — decide from the load diagram, not from habit.
- Grease packs must leave free volume inside the 28.575 mm-wide set; over-greasing a pair churning near the oil-band speed of 3,100 r/min raises temperature and destroys the setting.
- Replacing one half of an adjusted pair without resetting end play negates the 28.575 mm T logic: re-adjust the set and re-verify the contact pattern rather than reusing the old spacer stack.
- The 153/215 kN ratings here are NTN Ball and Roller Bearings CAT.No.2203E figures for 4T-42350/42584; internal geometry legitimately differs between inch-series makers, so re-verify ratings, adjustment and the exact cone/cup references before substituting another brand on a rated drive.
Frequently asked questions
What are the dimensions and catalogue ratings of NTN 4T-42350/42584?
4T-42350/42584 is an inch-series single-row tapered roller bearing to the ABMA boundary plan: 88.9 mm bore (3.5 in), 148.43 mm outside diameter and 28.575 mm assembled width T (5.844 × 1.125 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 153 kN, C0 215 kN, grease limiting speed 2,300 r/min, oil speed 3,100 r/min, mass about 1950 g. It is an open, separable cone/cup set with a pressed-steel cage.
Are the cone and cup of 4T-42350/42584 interchangeable separately?
Yes — ABMA inch parts are individually interchangeable: the 42350 cone or the 42584 cup can be replaced by an identical reference from NTN or another ABMA-dimensioned maker. Pairing the cone with a different cup reference is a different catalogue row: OD, assembled T and the 153/215 kN ratings change with the cup.
What is the difference between 4T-42350/42584 and a metric ISO 355 tapered bearing?
4T-42350/42584 follows the ABMA inch boundary plan with cone/cup references; ISO 355 bearings use metric dimension-series numbers (302, 322, …). Even where a metric size looks close to 88.9×148.43×28.575 mm, the envelopes and contact angles differ — the two systems are not drop-in interchangeable; check every boundary value before substituting.
What does the 4T prefix on 4T-42350/42584 mean?
4T is NTN's tapered roller bearing quality mark, stamped on cone and cup in the factory. It identifies NTN's 4T programme and is not a dimension or variant code, so interchange lists quote the bare 42350/42584 references; the 4T spelling is retained among this page's search aliases.
Why does 4T-42350/42584 list two speeds, 2,300 and 3,100 r/min?
The lower figure, 2,300 r/min, is the grease-lubricated limiting speed — the mechanical ceiling for the cage, rollers and cone-rib contact. With oil lubrication NTN rates 4T-42350/42584 at 3,100 r/min because oil removes rib-contact heat better. Real limits still depend on pair adjustment, oil flow and cooling.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN 2203E 2026-09-25 on 2026-10-01. Read our editorial & correction policy.