48290-48220-NTN bearing: complete specifications & equivalents
The 48290-48220-NTN is a ANSI ABMA 19.2 radial bearing sized 127 x 182.562 x 39.688 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 127 mm |
| Outer diameter D | 182.562 mm |
| Width B | 39.688 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel |
| Basic dynamic load rating C | 249 kN |
| Basic static load rating C0 | 435 kN |
| Limiting speed (mechanical) | 1800 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 3330 g |
| Manufacturer designation | NTN 4T-48290/48220 |
| Standard | ANSI ABMA 19.2 |
| Catalog version | NTN 2203E 2026-09-25 |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN 2203E 2026-09-25) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN 2203E 2026-09-25); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 4t-inch-series range
| Bore d | 5 in |
|---|---|
| Outer diameter D | 7.187 in |
| Width B | 1.563 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 27.8 mm |
| Smallest bore in 4t-inch-series | 12.7 mm |
| Largest outer diameter in 4t-inch-series | 260 mm |
| Width range across 4t-inch-series | 10.998–77.788 mm |
| Bore position in 4t-inch-series (smallest first) | 133 of 148 |
| Bore above smallest 4t-inch-series size | 114.3 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 48290-48220 | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 127×182.562×39.688 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 48290-48220-NTN model number is decoded
In NTN Ball and Roller Bearings CAT.No.2203E, the order number 4T-48290/48220 denotes the pure-numeric inch family of NTN inch tapered roller bearings — cone 48290 and cup 48220 delivered as a matched, separable pair of 127 mm bore and 182.562 mm outside diameter. Letter prefixes inherited from the inch convention mark the load family: LM reads as light-medium, HM as heavy-medium, LL as extra-light, J-prefixed codes as metric-envelope families — 48290 sits in the pure-numeric inch family. Catalogue mass of the 4T-48290/48220 cone-plus-cup set is 3330 g; shaft and housing shoulders must carry that mass square to the axis during fitting. The printed 249/435 kN ratings belong to the assembled 48290+48220 pair; a sibling row using the same cone with a different cup carries its own rating row because the raceway track shifts with the cup. Back-to-back (O) and face-to-face (X) arrangements of two 4T-48290/48220 sets react differently to shaft bending; choose the orientation for the moment load before locking shoulder geometry.
Typical equipment & failure modes
Common applications
- heavy press and forging-machine drive shafts
- port-crane travel and hoist gearboxes
- cement-plant mill and kiln drive trains
- large shredder and recycler main shafts
Known failure patterns
- cone-rib and roller large-end smearing when the adjusted pair runs with preload but starved lubricant film
- cup creep and housing fretting when the cup seat is cut too loose for the rotating load
- flaking on one cone only when a bent shaft loads the O/X pair unevenly
- pressed-steel cage pocket wear from roller skid at light radial load and high speed
- indentation of the raceways by hard particles in an open, unsealed arrangement
Selection pitfalls — read before you substitute
- At 127 mm bore the 4T-48290/48220 set is adjusted with hydraulic nuts or measured shims on mill and crane positions; manual torque methods cannot control preload at the 249 kN C level.
- The pure-numeric inch family at 127 mm bore (182.562×39.688 mm assembled) is one of several inch families sharing similar bores; cross-series swaps change OD, T and contact angle, so match the full 48290/48220 reference at purchase.
- Quote the full 48290/48220 pair at ordering: the 48290 cone also ships against sibling cups, and a cup from another reference changes the 39.688 mm assembled width and the rating.
- Fit selection follows the rotating ring: a rotating cone on a 127 mm shaft takes a m6/n6 seat, and a rotating cup reverses the logic — decide from the load diagram, not from habit.
- An unloaded 4T-48290/48220 near 1,800 r/min lets rollers skid and smear the cone rib; spring-preload lightly loaded high-speed pairs.
- The 249/435 kN ratings here are NTN Ball and Roller Bearings CAT.No.2203E figures for 4T-48290/48220; internal geometry legitimately differs between inch-series makers, so re-verify ratings, adjustment and the exact cone/cup references before substituting another brand on a rated drive.
Frequently asked questions
What are the dimensions and catalogue ratings of NTN 4T-48290/48220?
4T-48290/48220 is an inch-series single-row tapered roller bearing to the ABMA boundary plan: 127 mm bore (5 in), 182.562 mm outside diameter and 39.688 mm assembled width T (7.187 × 1.563 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 249 kN, C0 435 kN, grease limiting speed 1,800 r/min, oil speed 2,400 r/min, mass about 3330 g. It is an open, separable cone/cup set with a pressed-steel cage.
Are the cone and cup of 4T-48290/48220 interchangeable separately?
Yes — ABMA inch parts are individually interchangeable: the 48290 cone or the 48220 cup can be replaced by an identical reference from NTN or another ABMA-dimensioned maker. Pairing the cone with a different cup reference is a different catalogue row: OD, assembled T and the 249/435 kN ratings change with the cup.
What is the difference between 4T-48290/48220 and a metric ISO 355 tapered bearing?
4T-48290/48220 follows the ABMA inch boundary plan with cone/cup references; ISO 355 bearings use metric dimension-series numbers (302, 322, …). Even where a metric size looks close to 127×182.562×39.688 mm, the envelopes and contact angles differ — the two systems are not drop-in interchangeable; check every boundary value before substituting.
What does the 4T prefix on 4T-48290/48220 mean?
4T is NTN's tapered roller bearing quality mark, stamped on cone and cup in the factory. It identifies NTN's 4T programme and is not a dimension or variant code, so interchange lists quote the bare 48290/48220 references; the 4T spelling is retained among this page's search aliases.
Why does 4T-48290/48220 list two speeds, 1,800 and 2,400 r/min?
The lower figure, 1,800 r/min, is the grease-lubricated limiting speed — the mechanical ceiling for the cage, rollers and cone-rib contact. With oil lubrication NTN rates 4T-48290/48220 at 2,400 r/min because oil removes rib-contact heat better. Real limits still depend on pair adjustment, oil flow and cooling.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN 2203E 2026-09-25 on 2026-10-01. Read our editorial & correction policy.