48393-48320 bearing: complete specifications & equivalents
The 48393-48320 is a ANSI ABMA 19.2 radial bearing sized 136.525 x 190.5 x 39.688 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 136.525 mm |
| Outer diameter D | 190.5 mm |
| Width B | 39.688 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel |
| Basic dynamic load rating C | 262 kN |
| Basic static load rating C0 | 475 kN |
| Limiting speed (mechanical) | 1700 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 3430 g |
| Manufacturer designation | NTN 4T-48393/48320 |
| Standard | ANSI ABMA 19.2 |
| Catalog version | NTN 2203E 2026-09-25 |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN 2203E 2026-09-25) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN 2203E 2026-09-25); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 4t-inch-series range
| Bore d | 5.375 in |
|---|---|
| Outer diameter D | 7.5 in |
| Width B | 1.563 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 27 mm |
| Smallest bore in 4t-inch-series | 12.7 mm |
| Largest outer diameter in 4t-inch-series | 260 mm |
| Width range across 4t-inch-series | 10.998–77.788 mm |
| Bore position in 4t-inch-series (smallest first) | 137 of 148 |
| Bore above smallest 4t-inch-series size | 123.825 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 48393 | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; brand-specific OEM equivalents (NSK/FAG/NTN) pending multi-source data. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 48393-48320 model number is decoded
For an inch shaft of 136.525 mm carrying combined radial and thrust load, NTN lists 4T-48393/48320, a single-row 4T tapered roller set of 262 kN C and 475 kN C0 inside the 190.5 mm OD cup. Reading the designation: 4T-48393/48320 follows the ABMA inch convention — the number before the slash is the cone (inner ring with roller set and cage), the number after the slash is the cup (outer ring), and the pure-numeric inch family lettering ties the pair to its boundary plan. Selection: C 262 kN against C0 475 kN gives a C0/C ratio of 1.81 for the 136.525 mm bore; the pair is counted as one adjusted unit when checking L10 at the equivalent combined load. Housing fitment sequence for 4T-48393/48320: press the 48320 cup square into the 190.5 mm seat first, then bring the 48393 cone (on its 136.525 mm shaft) into adjustment — the two references are separate engineering parts that happen to ship as one set. Minimum load matters at speed: an unloaded 4T-48393/48320 run near 1,700 r/min lets the rollers skid; lightly spring-preload high-speed pair arrangements.
Typical equipment & failure modes
Common applications
- rolling-mill pinion stands and roll-neck auxiliaries
- mine hoist and dragline drum shafts
- heavy press and forging-machine drive shafts
- port-crane travel and hoist gearboxes
Known failure patterns
- cone-rib and roller large-end smearing when the adjusted pair runs with preload but starved lubricant film
- false brinelling on a stationary pair exposed to vibration during transport or standby
- preload loss and noise after one bearing of the adjusted pair is replaced without resetting end play
- pressed-steel cage pocket wear from roller skid at light radial load and high speed
- edge loading when shaft deflection exceeds the few arc-minutes an adjusted pair tolerates
Selection pitfalls — read before you substitute
- At 136.525 mm bore the 4T-48393/48320 set is adjusted with hydraulic nuts or measured shims on mill and crane positions; manual torque methods cannot control preload at the 262 kN C level.
- The pure-numeric inch family at 136.525 mm bore (190.5×39.688 mm assembled) is one of several inch families sharing similar bores; cross-series swaps change OD, T and contact angle, so match the full 48393/48320 reference at purchase.
- ABMA makes the 136.525×190.5 mm envelope interchangeable, not the ratings: NTN prints 262/475 kN for this execution and another make of the same number can differ in roller complement.
- ABMA makes the 136.525×190.5 mm envelope interchangeable, not the ratings: NTN prints 262/475 kN for this execution and another make of the same number can differ in roller complement.
- Shaft and housing fillets must clear the ring chamfers of 48393 and 48320; use undercut shoulders so the rings seat on the face, not on a radius.
- The 262/475 kN ratings here are NTN Ball and Roller Bearings CAT.No.2203E figures for 4T-48393/48320; internal geometry legitimately differs between inch-series makers, so re-verify ratings, adjustment and the exact cone/cup references before substituting another brand on a rated drive.
Frequently asked questions
What are the dimensions and catalogue ratings of NTN 4T-48393/48320?
4T-48393/48320 is an inch-series single-row tapered roller bearing to the ABMA boundary plan: 136.525 mm bore (5.375 in), 190.5 mm outside diameter and 39.688 mm assembled width T (7.5 × 1.563 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 262 kN, C0 475 kN, grease limiting speed 1,700 r/min, oil speed 2,300 r/min, mass about 3430 g. It is an open, separable cone/cup set with a pressed-steel cage.
Are the cone and cup of 4T-48393/48320 interchangeable separately?
Yes — ABMA inch parts are individually interchangeable: the 48393 cone or the 48320 cup can be replaced by an identical reference from NTN or another ABMA-dimensioned maker. Pairing the cone with a different cup reference is a different catalogue row: OD, assembled T and the 262/475 kN ratings change with the cup.
What is the difference between 4T-48393/48320 and a metric ISO 355 tapered bearing?
4T-48393/48320 follows the ABMA inch boundary plan with cone/cup references; ISO 355 bearings use metric dimension-series numbers (302, 322, …). Even where a metric size looks close to 136.525×190.5×39.688 mm, the envelopes and contact angles differ — the two systems are not drop-in interchangeable; check every boundary value before substituting.
What does the 4T prefix on 4T-48393/48320 mean?
4T is NTN's tapered roller bearing quality mark, stamped on cone and cup in the factory. It identifies NTN's 4T programme and is not a dimension or variant code, so interchange lists quote the bare 48393/48320 references; the 4T spelling is retained among this page's search aliases.
Why does 4T-48393/48320 list two speeds, 1,700 and 2,300 r/min?
The lower figure, 1,700 r/min, is the grease-lubricated limiting speed — the mechanical ceiling for the cage, rollers and cone-rib contact. With oil lubrication NTN rates 4T-48393/48320 at 2,300 r/min because oil removes rib-contact heat better. Real limits still depend on pair adjustment, oil flow and cooling.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN 2203E 2026-09-25 on 2026-10-01. Read our editorial & correction policy.