6277-6220 bearing: complete specifications & equivalents
The 6277-6220 is a ANSI ABMA 19.2 radial bearing sized 44.983 x 127 x 50.8 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 44.983 mm |
| Outer diameter D | 127 mm |
| Width B | 50.8 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel |
| Basic dynamic load rating C | 277 kN |
| Basic static load rating C0 | 320 kN |
| Limiting speed (mechanical) | 3200 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 3590 g |
| Manufacturer designation | NTN 4T-6277/6220 |
| Standard | ANSI ABMA 19.2 |
| Catalog version | NTN 2203E 2026-09-25 |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN 2203E 2026-09-25) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN 2203E 2026-09-25); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 4t-inch-series range
| Bore d | 1.771 in |
|---|---|
| Outer diameter D | 5 in |
| Width B | 2 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 41 mm |
| Smallest bore in 4t-inch-series | 12.7 mm |
| Largest outer diameter in 4t-inch-series | 260 mm |
| Width range across 4t-inch-series | 10.998–77.788 mm |
| Bore position in 4t-inch-series (smallest first) | 52 of 148 |
| Bore above smallest 4t-inch-series size | 32.283 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 6277 | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; brand-specific OEM equivalents (NSK/FAG/NTN) pending multi-source data. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 6277-6220 model number is decoded
4T-6277/6220 belongs to the NTN inch 4T tapered roller range (pure-numeric inch family); cone and cup are ordered by their own references and are individually interchangeable with like-numbered parts. Unlike ISO 355 metric numbers, this ABMA code does not encode the bore arithmetically: 6277 identifies the cone of 44.983 mm (1.771 in) bore by catalogue lookup, and 6220 fixes the 127 mm OD. Catalogue mass of the 4T-6277/6220 cone-plus-cup set is 3590 g; shaft and housing shoulders must carry that mass square to the axis during fitting. Cup-side note for 6220: within the pure-numeric inch family tables the 6277 cone is listed against several cup options, and it is the cup that fixes the 127 mm OD and the 50.8 mm assembled width — quote the full 6277/6220 pair, never the cone alone. With a rotating shaft a k5/m5 cone seat and an easy-push cup seat are typical practice for 4T-6277/6220; reverse the fit logic when the cup rotates.
Typical equipment & failure modes
Common applications
- construction-equipment pivot and wheel positions
- mining and quarry conveyor drive pulleys
- machine-tool headstocks on inch spindles
- pump and blower drive shafts with combined load
Known failure patterns
- cone-rib and roller large-end smearing when the adjusted pair runs with preload but starved lubricant film
- flaking on one cone only when a bent shaft loads the O/X pair unevenly
- cup creep and housing fretting when the cup seat is cut too loose for the rotating load
- pressed-steel cage pocket wear from roller skid at light radial load and high speed
- brinell marks on cone and cup raceways from impact during handling or hammer fitting
Selection pitfalls — read before you substitute
- Hub and pinion positions of this 44.983 mm class are adjusted in pairs; verify end play against the axle or gearbox drawing and re-torque after bedding-in instead of trusting the first setting on 4T-6277/6220.
- The pure-numeric inch family at 44.983 mm bore (127×50.8 mm assembled) is one of several inch families sharing similar bores; cross-series swaps change OD, T and contact angle, so match the full 6277/6220 reference at purchase.
- Do not confuse T (50.8 mm, the assembled cone-plus-cup width) with the cone width when drawing spacers; an abutment sized to T leaves the cup unseated.
- Do not confuse T (50.8 mm, the assembled cone-plus-cup width) with the cone width when drawing spacers; an abutment sized to T leaves the cup unseated.
- Open 4T-6277/6220 sets have no seals: a hub or gearbox needs external sealing or the 3,200 r/min grease figure is meaningless once water reaches the cone rib.
- The 277/320 kN ratings here are NTN Ball and Roller Bearings CAT.No.2203E figures for 4T-6277/6220; internal geometry legitimately differs between inch-series makers, so re-verify ratings, adjustment and the exact cone/cup references before substituting another brand on a rated drive.
Frequently asked questions
What are the dimensions and catalogue ratings of NTN 4T-6277/6220?
4T-6277/6220 is an inch-series single-row tapered roller bearing to the ABMA boundary plan: 44.983 mm bore (1.771 in), 127 mm outside diameter and 50.8 mm assembled width T (5 × 2 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 277 kN, C0 320 kN, grease limiting speed 3,200 r/min, oil speed 4,300 r/min, mass about 3590 g. It is an open, separable cone/cup set with a pressed-steel cage.
Are the cone and cup of 4T-6277/6220 interchangeable separately?
Yes — ABMA inch parts are individually interchangeable: the 6277 cone or the 6220 cup can be replaced by an identical reference from NTN or another ABMA-dimensioned maker. Pairing the cone with a different cup reference is a different catalogue row: OD, assembled T and the 277/320 kN ratings change with the cup.
What is the difference between 4T-6277/6220 and a metric ISO 355 tapered bearing?
4T-6277/6220 follows the ABMA inch boundary plan with cone/cup references; ISO 355 bearings use metric dimension-series numbers (302, 322, …). Even where a metric size looks close to 44.983×127×50.8 mm, the envelopes and contact angles differ — the two systems are not drop-in interchangeable; check every boundary value before substituting.
What does the 4T prefix on 4T-6277/6220 mean?
4T is NTN's tapered roller bearing quality mark, stamped on cone and cup in the factory. It identifies NTN's 4T programme and is not a dimension or variant code, so interchange lists quote the bare 6277/6220 references; the 4T spelling is retained among this page's search aliases.
Why does 4T-6277/6220 list two speeds, 3,200 and 4,300 r/min?
The lower figure, 3,200 r/min, is the grease-lubricated limiting speed — the mechanical ceiling for the cage, rollers and cone-rib contact. With oil lubrication NTN rates 4T-6277/6220 at 4,300 r/min because oil removes rib-contact heat better. Real limits still depend on pair adjustment, oil flow and cooling.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN 2203E 2026-09-25 on 2026-10-01. Read our editorial & correction policy.