740-742 bearing: complete specifications & equivalents
The 740-742 is a ANSI ABMA 19.2 radial bearing sized 80.962 x 150.089 x 44.45 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 80.962 mm |
| Outer diameter D | 150.089 mm |
| Width B | 44.45 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel |
| Basic dynamic load rating C | 289 kN |
| Basic static load rating C0 | 360 kN |
| Limiting speed (mechanical) | 2400 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 3440 g |
| Manufacturer designation | NTN 4T-740/742 |
| Standard | ANSI ABMA 19.2 |
| Catalog version | NTN 2203E 2026-09-25 |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN 2203E 2026-09-25) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN 2203E 2026-09-25); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 4t-inch-series range
| Bore d | 3.187 in |
|---|---|
| Outer diameter D | 5.909 in |
| Width B | 1.75 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 34.6 mm |
| Smallest bore in 4t-inch-series | 12.7 mm |
| Largest outer diameter in 4t-inch-series | 260 mm |
| Width range across 4t-inch-series | 10.998–77.788 mm |
| Bore position in 4t-inch-series (smallest first) | 98 of 148 |
| Bore above smallest 4t-inch-series size | 68.262 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 740 | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; brand-specific OEM equivalents (NSK/FAG/NTN) pending multi-source data. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 740-742 model number is decoded
For an inch shaft of 80.962 mm carrying combined radial and thrust load, NTN lists 4T-740/742, a single-row 4T tapered roller set of 289 kN C and 360 kN C0 inside the 150.089 mm OD cup. Cone and cup of 4T-740/742 are separately stocked parts: a worn 742 cup can be replaced against the existing 740 cone, provided the new cup carries the identical reference — pairing across references changes the 44.45 mm assembled width and the rating. The 34.6 mm radial section over the 80.962 mm bore positions the contact line of the pair; abutment shoulders and spacers are dimensioned from that geometry, not from the bore alone. Housing fitment sequence for 4T-740/742: press the 742 cup square into the 150.089 mm seat first, then bring the 740 cone (on its 80.962 mm shaft) into adjustment — the two references are separate engineering parts that happen to ship as one set. NTN grades inch 4T bearings as open bearings without integral seals; at 80.962 mm bore the application supplies sealing and the grease fill or oil feed.
Typical equipment & failure modes
Common applications
- crusher and screening-plant eccentric shafts
- heavy truck and bus drive-axle differentials
- plant gearboxes on inch-dimensioned shaft lines
- large conveyor head pulleys in bulk-handling plant
Known failure patterns
- rib-face scoring when the thrust share of the combined load exceeds what the cone rib of this size carries
- flaking on one cone only when a bent shaft loads the O/X pair unevenly
- cup creep and housing fretting when the cup seat is cut too loose for the rotating load
- pressed-steel cage pocket wear from roller skid at light radial load and high speed
- edge loading when shaft deflection exceeds the few arc-minutes an adjusted pair tolerates
Selection pitfalls — read before you substitute
- Mount the 80.962 mm cone by induction heating (max 120 °C) and the 150.089 mm cup with a press sleeve; at 3440 g a cocked ring brinells the raceway directly.
- The pure-numeric inch family at 80.962 mm bore (150.089×44.45 mm assembled) is one of several inch families sharing similar bores; cross-series swaps change OD, T and contact angle, so match the full 740/742 reference at purchase.
- Open 4T-740/742 sets have no seals: a hub or gearbox needs external sealing or the 2,400 r/min grease figure is meaningless once water reaches the cone rib.
- Never drive the 150.089 mm cup home through the rollers: fitting force goes through the ring faces only, or brinell marks release as noise within the first running hours.
- An unloaded 4T-740/742 near 2,400 r/min lets rollers skid and smear the cone rib; spring-preload lightly loaded high-speed pairs.
- The 289/360 kN ratings here are NTN Ball and Roller Bearings CAT.No.2203E figures for 4T-740/742; internal geometry legitimately differs between inch-series makers, so re-verify ratings, adjustment and the exact cone/cup references before substituting another brand on a rated drive.
Frequently asked questions
What are the dimensions and catalogue ratings of NTN 4T-740/742?
4T-740/742 is an inch-series single-row tapered roller bearing to the ABMA boundary plan: 80.962 mm bore (3.187 in), 150.089 mm outside diameter and 44.45 mm assembled width T (5.909 × 1.75 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 289 kN, C0 360 kN, grease limiting speed 2,400 r/min, oil speed 3,200 r/min, mass about 3440 g. It is an open, separable cone/cup set with a pressed-steel cage.
Are the cone and cup of 4T-740/742 interchangeable separately?
Yes — ABMA inch parts are individually interchangeable: the 740 cone or the 742 cup can be replaced by an identical reference from NTN or another ABMA-dimensioned maker. Pairing the cone with a different cup reference is a different catalogue row: OD, assembled T and the 289/360 kN ratings change with the cup.
What is the difference between 4T-740/742 and a metric ISO 355 tapered bearing?
4T-740/742 follows the ABMA inch boundary plan with cone/cup references; ISO 355 bearings use metric dimension-series numbers (302, 322, …). Even where a metric size looks close to 80.962×150.089×44.45 mm, the envelopes and contact angles differ — the two systems are not drop-in interchangeable; check every boundary value before substituting.
What does the 4T prefix on 4T-740/742 mean?
4T is NTN's tapered roller bearing quality mark, stamped on cone and cup in the factory. It identifies NTN's 4T programme and is not a dimension or variant code, so interchange lists quote the bare 740/742 references; the 4T spelling is retained among this page's search aliases.
Why does 4T-740/742 list two speeds, 2,400 and 3,200 r/min?
The lower figure, 2,400 r/min, is the grease-lubricated limiting speed — the mechanical ceiling for the cage, rollers and cone-rib contact. With oil lubrication NTN rates 4T-740/742 at 3,200 r/min because oil removes rib-contact heat better. Real limits still depend on pair adjustment, oil flow and cooling.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN 2203E 2026-09-25 on 2026-10-01. Read our editorial & correction policy.