757-752 bearing: complete specifications & equivalents
The 757-752 is a ANSI ABMA 19.2 radial bearing sized 82.55 x 161.925 x 47.625 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 82.55 mm |
| Outer diameter D | 161.925 mm |
| Width B | 47.625 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel |
| Basic dynamic load rating C | 299 kN |
| Basic static load rating C0 | 385 kN |
| Limiting speed (mechanical) | 2300 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 4420 g |
| Manufacturer designation | NTN 4T-757/752 |
| Standard | ANSI ABMA 19.2 |
| Catalog version | NTN 2203E 2026-09-25 |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN 2203E 2026-09-25) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN 2203E 2026-09-25); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 4t-inch-series range
| Bore d | 3.25 in |
|---|---|
| Outer diameter D | 6.375 in |
| Width B | 1.875 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 39.7 mm |
| Smallest bore in 4t-inch-series | 12.7 mm |
| Largest outer diameter in 4t-inch-series | 260 mm |
| Width range across 4t-inch-series | 10.998–77.788 mm |
| Bore position in 4t-inch-series (smallest first) | 99 of 148 |
| Bore above smallest 4t-inch-series size | 69.85 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 757 | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; brand-specific OEM equivalents (NSK/FAG/NTN) pending multi-source data. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 757-752 model number is decoded
NTN supplies this 3.25 in (82.55 mm) shaft position as 4T-757/752: cone 757, cup 752, profiled rollers and a pressed-steel cage, rated 299 kN basic dynamic and 385 kN static. The 4T prefix is NTN's tapered roller quality mark stamped on both parts; it is a brand mark, not a size code, so cross-references quote 757/752 without it. The 3.6 kN of dynamic capacity per millimetre of bore summarises the 299 kN rating over the 82.55 mm bore — sanity-check any interchange candidate against this ratio and the 47.625 mm T. Housing fitment sequence for 4T-757/752: press the 752 cup square into the 161.925 mm seat first, then bring the 757 cone (on its 82.55 mm shaft) into adjustment — the two references are separate engineering parts that happen to ship as one set. With a rotating shaft a k5/m5 cone seat and an easy-push cup seat are typical practice for 4T-757/752; reverse the fit logic when the cup rotates.
Typical equipment & failure modes
Common applications
- paper-machine and calender roll supports
- off-highway and forestry machine axles
- marine winch and deck-machinery shafts
- crusher and screening-plant eccentric shafts
Known failure patterns
- cone-rib and roller large-end smearing when the adjusted pair runs with preload but starved lubricant film
- cup creep and housing fretting when the cup seat is cut too loose for the rotating load
- flaking on one cone only when a bent shaft loads the O/X pair unevenly
- pressed-steel cage pocket wear from roller skid at light radial load and high speed
- fretting corrosion on a loose cone seat that creeps under rotating load
Selection pitfalls — read before you substitute
- Mount the 82.55 mm cone by induction heating (max 120 °C) and the 161.925 mm cup with a press sleeve; at 4420 g a cocked ring brinells the raceway directly.
- The pure-numeric inch family at 82.55 mm bore (161.925×47.625 mm assembled) is one of several inch families sharing similar bores; cross-series swaps change OD, T and contact angle, so match the full 757/752 reference at purchase.
- Grease packs must leave free volume inside the 47.625 mm-wide set; over-greasing a pair churning near the oil-band speed of 3,100 r/min raises temperature and destroys the setting.
- An unloaded 4T-757/752 near 2,300 r/min lets rollers skid and smear the cone rib; spring-preload lightly loaded high-speed pairs.
- Inch and metric bores collide on paper — 82.55 mm is 3.25 in, not a round metric size; a metric bearing that seems 0.1 mm off will not seat on the inch shaft.
- The 299/385 kN ratings here are NTN Ball and Roller Bearings CAT.No.2203E figures for 4T-757/752; internal geometry legitimately differs between inch-series makers, so re-verify ratings, adjustment and the exact cone/cup references before substituting another brand on a rated drive.
Frequently asked questions
What are the dimensions and catalogue ratings of NTN 4T-757/752?
4T-757/752 is an inch-series single-row tapered roller bearing to the ABMA boundary plan: 82.55 mm bore (3.25 in), 161.925 mm outside diameter and 47.625 mm assembled width T (6.375 × 1.875 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 299 kN, C0 385 kN, grease limiting speed 2,300 r/min, oil speed 3,100 r/min, mass about 4420 g. It is an open, separable cone/cup set with a pressed-steel cage.
Are the cone and cup of 4T-757/752 interchangeable separately?
Yes — ABMA inch parts are individually interchangeable: the 757 cone or the 752 cup can be replaced by an identical reference from NTN or another ABMA-dimensioned maker. Pairing the cone with a different cup reference is a different catalogue row: OD, assembled T and the 299/385 kN ratings change with the cup.
What is the difference between 4T-757/752 and a metric ISO 355 tapered bearing?
4T-757/752 follows the ABMA inch boundary plan with cone/cup references; ISO 355 bearings use metric dimension-series numbers (302, 322, …). Even where a metric size looks close to 82.55×161.925×47.625 mm, the envelopes and contact angles differ — the two systems are not drop-in interchangeable; check every boundary value before substituting.
What does the 4T prefix on 4T-757/752 mean?
4T is NTN's tapered roller bearing quality mark, stamped on cone and cup in the factory. It identifies NTN's 4T programme and is not a dimension or variant code, so interchange lists quote the bare 757/752 references; the 4T spelling is retained among this page's search aliases.
Why does 4T-757/752 list two speeds, 2,300 and 3,100 r/min?
The lower figure, 2,300 r/min, is the grease-lubricated limiting speed — the mechanical ceiling for the cage, rollers and cone-rib contact. With oil lubrication NTN rates 4T-757/752 at 3,100 r/min because oil removes rib-contact heat better. Real limits still depend on pair adjustment, oil flow and cooling.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN 2203E 2026-09-25 on 2026-10-01. Read our editorial & correction policy.