H913842-H913810 bearing: complete specifications & equivalents
The H913842-H913810 is a ANSI ABMA 19.2 radial bearing sized 61.912 x 146.05 x 41.275 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 61.912 mm |
| Outer diameter D | 146.05 mm |
| Width B | 41.275 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel |
| Basic dynamic load rating C | 220 kN |
| Basic static load rating C0 | 234 kN |
| Limiting speed (mechanical) | 2400 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 3170 g |
| Manufacturer designation | NTN 4T-H913842/H913810 |
| Standard | ANSI ABMA 19.2 |
| Catalog version | NTN 2203E 2026-09-25 |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN 2203E 2026-09-25) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN 2203E 2026-09-25); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 4t-inch-series range
| Bore d | 2.437 in |
|---|---|
| Outer diameter D | 5.75 in |
| Width B | 1.625 in |
| ISO bore code | 42 |
| Radial section height (D−d)/2 | 42.1 mm |
| Smallest bore in 4t-inch-series | 12.7 mm |
| Largest outer diameter in 4t-inch-series | 260 mm |
| Width range across 4t-inch-series | 10.998–77.788 mm |
| Bore position in 4t-inch-series (smallest first) | 78 of 148 |
| Bore above smallest 4t-inch-series size | 49.212 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| H913842 | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; brand-specific OEM equivalents (NSK/FAG/NTN) pending multi-source data. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the H913842-H913810 model number is decoded
The NTN 2203E inch table prints 4T-H913842/H913810 at 61.912 mm bore (2.437 in), 146.05 mm cup OD and 41.275 mm assembled T, with a grease limiting speed of 2,400 r/min and an oil ceiling of 3,200 r/min. Letter prefixes inherited from the inch convention mark the load family: LM reads as light-medium, HM as heavy-medium, LL as extra-light, J-prefixed codes as metric-envelope families — H913842 sits in the heavy H family. Imperial cross-check for the drawing: 61.912×146.05×41.275 mm converts to 2.437 × 5.75 × 1.625 in; the ABMA envelope swaps with like-numbered inch parts but the 220/234 kN ratings are NTN-specific. Housing fitment sequence for 4T-H913842/H913810: press the H913810 cup square into the 146.05 mm seat first, then bring the H913842 cone (on its 61.912 mm shaft) into adjustment — the two references are separate engineering parts that happen to ship as one set. NTN grades inch 4T bearings as open bearings without integral seals; at 61.912 mm bore the application supplies sealing and the grease fill or oil feed.
Typical equipment & failure modes
Common applications
- paper-machine and calender roll supports
- off-highway and forestry machine axles
- marine winch and deck-machinery shafts
- crusher and screening-plant eccentric shafts
Known failure patterns
- rib-face scoring when the thrust share of the combined load exceeds what the cone rib of this size carries
- preload loss and noise after one bearing of the adjusted pair is replaced without resetting end play
- false brinelling on a stationary pair exposed to vibration during transport or standby
- cage fatigue when the pair runs continuously near the grease limiting speed without oil cooling
- edge loading when shaft deflection exceeds the few arc-minutes an adjusted pair tolerates
Selection pitfalls — read before you substitute
- Mount the 61.912 mm cone by induction heating (max 120 °C) and the 146.05 mm cup with a press sleeve; at 3170 g a cocked ring brinells the raceway directly.
- The heavy H family at 61.912 mm bore (146.05×41.275 mm assembled) is one of several inch families sharing similar bores; cross-series swaps change OD, T and contact angle, so match the full H913842/H913810 reference at purchase.
- An unloaded 4T-H913842/H913810 near 2,400 r/min lets rollers skid and smear the cone rib; spring-preload lightly loaded high-speed pairs.
- Replacing one half of an adjusted pair without resetting end play negates the 41.275 mm T logic: re-adjust the set and re-verify the contact pattern rather than reusing the old spacer stack.
- Grease packs must leave free volume inside the 41.275 mm-wide set; over-greasing a pair churning near the oil-band speed of 3,200 r/min raises temperature and destroys the setting.
- The 220/234 kN ratings here are NTN Ball and Roller Bearings CAT.No.2203E figures for 4T-H913842/H913810; internal geometry legitimately differs between inch-series makers, so re-verify ratings, adjustment and the exact cone/cup references before substituting another brand on a rated drive.
Frequently asked questions
What are the dimensions and catalogue ratings of NTN 4T-H913842/H913810?
4T-H913842/H913810 is an inch-series single-row tapered roller bearing to the ABMA boundary plan: 61.912 mm bore (2.437 in), 146.05 mm outside diameter and 41.275 mm assembled width T (5.75 × 1.625 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 220 kN, C0 234 kN, grease limiting speed 2,400 r/min, oil speed 3,200 r/min, mass about 3170 g. It is an open, separable cone/cup set with a pressed-steel cage.
Are the cone and cup of 4T-H913842/H913810 interchangeable separately?
Yes — ABMA inch parts are individually interchangeable: the H913842 cone or the H913810 cup can be replaced by an identical reference from NTN or another ABMA-dimensioned maker. Pairing the cone with a different cup reference is a different catalogue row: OD, assembled T and the 220/234 kN ratings change with the cup.
What is the difference between 4T-H913842/H913810 and a metric ISO 355 tapered bearing?
4T-H913842/H913810 follows the ABMA inch boundary plan with cone/cup references; ISO 355 bearings use metric dimension-series numbers (302, 322, …). Even where a metric size looks close to 61.912×146.05×41.275 mm, the envelopes and contact angles differ — the two systems are not drop-in interchangeable; check every boundary value before substituting.
What does the 4T prefix on 4T-H913842/H913810 mean?
4T is NTN's tapered roller bearing quality mark, stamped on cone and cup in the factory. It identifies NTN's 4T programme and is not a dimension or variant code, so interchange lists quote the bare H913842/H913810 references; the 4T spelling is retained among this page's search aliases.
Why does 4T-H913842/H913810 list two speeds, 2,400 and 3,200 r/min?
The lower figure, 2,400 r/min, is the grease-lubricated limiting speed — the mechanical ceiling for the cage, rollers and cone-rib contact. With oil lubrication NTN rates 4T-H913842/H913810 at 3,200 r/min because oil removes rib-contact heat better. Real limits still depend on pair adjustment, oil flow and cooling.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN 2203E 2026-09-25 on 2026-10-01. Read our editorial & correction policy.