HM807046-HM807010 bearing: complete specifications & equivalents
The HM807046-HM807010 is a ANSI ABMA 19.2 radial bearing sized 50.8 x 104.775 x 36.512 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 50.8 mm |
| Outer diameter D | 104.775 mm |
| Width B | 36.512 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel |
| Basic dynamic load rating C | 153 kN |
| Basic static load rating C0 | 189 kN |
| Limiting speed (mechanical) | 3600 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 1480 g |
| Manufacturer designation | NTN 4T-HM807046/HM807010 |
| Standard | ANSI ABMA 19.2 |
| Catalog version | NTN 2203E 2026-09-25 |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN 2203E 2026-09-25) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN 2203E 2026-09-25); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 4t-inch-series range
| Bore d | 2 in |
|---|---|
| Outer diameter D | 4.125 in |
| Width B | 1.437 in |
| ISO bore code | 46 |
| Radial section height (D−d)/2 | 27 mm |
| Smallest bore in 4t-inch-series | 12.7 mm |
| Largest outer diameter in 4t-inch-series | 260 mm |
| Width range across 4t-inch-series | 10.998–77.788 mm |
| Bore position in 4t-inch-series (smallest first) | 64 of 148 |
| Bore above smallest 4t-inch-series size | 38.099999999999994 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| HM807046-010 | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 50.8×104.775×36.512 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the HM807046-HM807010 model number is decoded
4T-HM807046/HM807010 is the NTN 4T catalogue entry for a 50.8×104.775×36.512 mm inch tapered roller bearing — an ABMA-dimensioned cone/cup set, not an ISO 355 metric bearing, even though the table quotes metric equivalents. The 4T prefix is NTN's tapered roller quality mark stamped on both parts; it is a brand mark, not a size code, so cross-references quote HM807046/HM807010 without it. Catalogue mass of the 4T-HM807046/HM807010 cone-plus-cup set is 1480 g; shaft and housing shoulders must carry that mass square to the axis during fitting. Housing fitment sequence for 4T-HM807046/HM807010: press the HM807010 cup square into the 104.775 mm seat first, then bring the HM807046 cone (on its 50.8 mm shaft) into adjustment — the two references are separate engineering parts that happen to ship as one set. The rollers run with their large ends against the cone's guide rib; lubricant must reach that rib face of 4T-HM807046/HM807010, not only the raceway, or the pair smears on the first overloaded start.
Typical equipment & failure modes
Common applications
- construction-equipment pivot and wheel positions
- mining and quarry conveyor drive pulleys
- machine-tool headstocks on inch spindles
- pump and blower drive shafts with combined load
Known failure patterns
- cone-rib and roller large-end smearing when the adjusted pair runs with preload but starved lubricant film
- cup creep and housing fretting when the cup seat is cut too loose for the rotating load
- flaking on one cone only when a bent shaft loads the O/X pair unevenly
- cage fatigue when the pair runs continuously near the grease limiting speed without oil cooling
- edge loading when shaft deflection exceeds the few arc-minutes an adjusted pair tolerates
Selection pitfalls — read before you substitute
- Hub and pinion positions of this 50.8 mm class are adjusted in pairs; verify end play against the axle or gearbox drawing and re-torque after bedding-in instead of trusting the first setting on 4T-HM807046/HM807010.
- The heavy-medium HM family is proportioned for a high thrust share; swapping to a lighter LM or pure-numeric series at the same 50.8 mm bore cuts axial capacity even when the envelope fits — re-verify the load split before downgrading.
- Shaft and housing fillets must clear the ring chamfers of HM807046 and HM807010; use undercut shoulders so the rings seat on the face, not on a radius.
- Shaft and housing fillets must clear the ring chamfers of HM807046 and HM807010; use undercut shoulders so the rings seat on the face, not on a radius.
- Quote the full HM807046/HM807010 pair at ordering: the HM807046 cone also ships against sibling cups, and a cup from another reference changes the 36.512 mm assembled width and the rating.
- The 153/189 kN ratings here are NTN Ball and Roller Bearings CAT.No.2203E figures for 4T-HM807046/HM807010; internal geometry legitimately differs between inch-series makers, so re-verify ratings, adjustment and the exact cone/cup references before substituting another brand on a rated drive.
Frequently asked questions
What are the dimensions and catalogue ratings of NTN 4T-HM807046/HM807010?
4T-HM807046/HM807010 is an inch-series single-row tapered roller bearing to the ABMA boundary plan: 50.8 mm bore (2 in), 104.775 mm outside diameter and 36.512 mm assembled width T (4.125 × 1.437 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 153 kN, C0 189 kN, grease limiting speed 3,600 r/min, oil speed 4,800 r/min, mass about 1480 g. It is an open, separable cone/cup set with a pressed-steel cage.
Are the cone and cup of 4T-HM807046/HM807010 interchangeable separately?
Yes — ABMA inch parts are individually interchangeable: the HM807046 cone or the HM807010 cup can be replaced by an identical reference from NTN or another ABMA-dimensioned maker. Pairing the cone with a different cup reference is a different catalogue row: OD, assembled T and the 153/189 kN ratings change with the cup.
What is the difference between 4T-HM807046/HM807010 and a metric ISO 355 tapered bearing?
4T-HM807046/HM807010 follows the ABMA inch boundary plan with cone/cup references; ISO 355 bearings use metric dimension-series numbers (302, 322, …). Even where a metric size looks close to 50.8×104.775×36.512 mm, the envelopes and contact angles differ — the two systems are not drop-in interchangeable; check every boundary value before substituting.
What does the 4T prefix on 4T-HM807046/HM807010 mean?
4T is NTN's tapered roller bearing quality mark, stamped on cone and cup in the factory. It identifies NTN's 4T programme and is not a dimension or variant code, so interchange lists quote the bare HM807046/HM807010 references; the 4T spelling is retained among this page's search aliases.
Why does 4T-HM807046/HM807010 list two speeds, 3,600 and 4,800 r/min?
The lower figure, 3,600 r/min, is the grease-lubricated limiting speed — the mechanical ceiling for the cage, rollers and cone-rib contact. With oil lubrication NTN rates 4T-HM807046/HM807010 at 4,800 r/min because oil removes rib-contact heat better. Real limits still depend on pair adjustment, oil flow and cooling.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN 2203E 2026-09-25 on 2026-10-01. Read our editorial & correction policy.