HM907643-HM907614 bearing: complete specifications & equivalents
The HM907643-HM907614 is a ANSI ABMA 19.2 radial bearing sized 50.8 x 111.125 x 30.162 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 50.8 mm |
| Outer diameter D | 111.125 mm |
| Width B | 30.162 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel |
| Basic dynamic load rating C | 115 kN |
| Basic static load rating C0 | 136 kN |
| Limiting speed (mechanical) | 3200 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 1360 g |
| Manufacturer designation | NTN 4T-HM907643/HM907614 |
| Standard | ANSI ABMA 19.2 |
| Catalog version | NTN 2203E 2026-09-25 |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN 2203E 2026-09-25) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN 2203E 2026-09-25); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 4t-inch-series range
| Bore d | 2 in |
|---|---|
| Outer diameter D | 4.375 in |
| Width B | 1.187 in |
| ISO bore code | 43 |
| Radial section height (D−d)/2 | 30.2 mm |
| Smallest bore in 4t-inch-series | 12.7 mm |
| Largest outer diameter in 4t-inch-series | 260 mm |
| Width range across 4t-inch-series | 10.998–77.788 mm |
| Bore position in 4t-inch-series (smallest first) | 64 of 148 |
| Bore above smallest 4t-inch-series size | 38.099999999999994 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| HM907643 | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; brand-specific OEM equivalents (NSK/FAG/NTN) pending multi-source data. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the HM907643-HM907614 model number is decoded
4T-HM907643/HM907614 belongs to the NTN inch 4T tapered roller range (heavy-medium HM family); cone and cup are ordered by their own references and are individually interchangeable with like-numbered parts. Cone and cup of 4T-HM907643/HM907614 are separately stocked parts: a worn HM907614 cup can be replaced against the existing HM907643 cone, provided the new cup carries the identical reference — pairing across references changes the 30.162 mm assembled width and the rating. Imperial cross-check for the drawing: 50.8×111.125×30.162 mm converts to 2 × 4.375 × 1.187 in; the ABMA envelope swaps with like-numbered inch parts but the 115/136 kN ratings are NTN-specific. The printed 115/136 kN ratings belong to the assembled HM907643+HM907614 pair; a sibling row using the same cone with a different cup carries its own rating row because the raceway track shifts with the cup. Contact-pattern check with marking blue: a pattern biased to one roller end means the 50.8 mm pair is misadjusted and the set will edge-load in service.
Typical equipment & failure modes
Common applications
- mining and quarry conveyor drive pulleys
- machine-tool headstocks on inch spindles
- pump and blower drive shafts with combined load
- truck and trailer axle hubs on inch-dimensioned axles
Known failure patterns
- cone-rib and roller large-end smearing when the adjusted pair runs with preload but starved lubricant film
- cup creep and housing fretting when the cup seat is cut too loose for the rotating load
- flaking on one cone only when a bent shaft loads the O/X pair unevenly
- pressed-steel cage pocket wear from roller skid at light radial load and high speed
- water-induced pitting when the open bearing sees washdown without external seals
Selection pitfalls — read before you substitute
- Hub and pinion positions of this 50.8 mm class are adjusted in pairs; verify end play against the axle or gearbox drawing and re-torque after bedding-in instead of trusting the first setting on 4T-HM907643/HM907614.
- The heavy-medium HM family is proportioned for a high thrust share; swapping to a lighter LM or pure-numeric series at the same 50.8 mm bore cuts axial capacity even when the envelope fits — re-verify the load split before downgrading.
- Replacing one half of an adjusted pair without resetting end play negates the 30.162 mm T logic: re-adjust the set and re-verify the contact pattern rather than reusing the old spacer stack.
- Open 4T-HM907643/HM907614 sets have no seals: a hub or gearbox needs external sealing or the 3,200 r/min grease figure is meaningless once water reaches the cone rib.
- Never drive the 111.125 mm cup home through the rollers: fitting force goes through the ring faces only, or brinell marks release as noise within the first running hours.
- The 115/136 kN ratings here are NTN Ball and Roller Bearings CAT.No.2203E figures for 4T-HM907643/HM907614; internal geometry legitimately differs between inch-series makers, so re-verify ratings, adjustment and the exact cone/cup references before substituting another brand on a rated drive.
Frequently asked questions
What are the dimensions and catalogue ratings of NTN 4T-HM907643/HM907614?
4T-HM907643/HM907614 is an inch-series single-row tapered roller bearing to the ABMA boundary plan: 50.8 mm bore (2 in), 111.125 mm outside diameter and 30.162 mm assembled width T (4.375 × 1.187 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 115 kN, C0 136 kN, grease limiting speed 3,200 r/min, oil speed 4,200 r/min, mass about 1360 g. It is an open, separable cone/cup set with a pressed-steel cage.
Are the cone and cup of 4T-HM907643/HM907614 interchangeable separately?
Yes — ABMA inch parts are individually interchangeable: the HM907643 cone or the HM907614 cup can be replaced by an identical reference from NTN or another ABMA-dimensioned maker. Pairing the cone with a different cup reference is a different catalogue row: OD, assembled T and the 115/136 kN ratings change with the cup.
What is the difference between 4T-HM907643/HM907614 and a metric ISO 355 tapered bearing?
4T-HM907643/HM907614 follows the ABMA inch boundary plan with cone/cup references; ISO 355 bearings use metric dimension-series numbers (302, 322, …). Even where a metric size looks close to 50.8×111.125×30.162 mm, the envelopes and contact angles differ — the two systems are not drop-in interchangeable; check every boundary value before substituting.
What does the 4T prefix on 4T-HM907643/HM907614 mean?
4T is NTN's tapered roller bearing quality mark, stamped on cone and cup in the factory. It identifies NTN's 4T programme and is not a dimension or variant code, so interchange lists quote the bare HM907643/HM907614 references; the 4T spelling is retained among this page's search aliases.
Why does 4T-HM907643/HM907614 list two speeds, 3,200 and 4,200 r/min?
The lower figure, 3,200 r/min, is the grease-lubricated limiting speed — the mechanical ceiling for the cage, rollers and cone-rib contact. With oil lubrication NTN rates 4T-HM907643/HM907614 at 4,200 r/min because oil removes rib-contact heat better. Real limits still depend on pair adjustment, oil flow and cooling.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN 2203E 2026-09-25 on 2026-10-01. Read our editorial & correction policy.