JHM911244-JHM911211 bearing: complete specifications & equivalents
The JHM911244-JHM911211 is a ANSI ABMA 19.2 radial bearing sized 60 x 130 x 34.1 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 60 mm |
| Outer diameter D | 130 mm |
| Width B | 34.1 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel |
| Basic dynamic load rating C | 173 kN |
| Basic static load rating C0 | 186 kN |
| Limiting speed (mechanical) | 2700 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 2010 g |
| Manufacturer designation | NTN 4T-JHM911244/JHM911211 |
| Standard | ANSI ABMA 19.2 |
| Catalog version | NTN 2203E 2026-09-25 |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN 2203E 2026-09-25) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN 2203E 2026-09-25); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 4t-inch-series range
| Bore d | 2.362 in |
|---|---|
| Outer diameter D | 5.118 in |
| Width B | 1.343 in |
| ISO bore code | 44 |
| Radial section height (D−d)/2 | 35 mm |
| Smallest bore in 4t-inch-series | 12.7 mm |
| Largest outer diameter in 4t-inch-series | 260 mm |
| Width range across 4t-inch-series | 10.998–77.788 mm |
| Bore position in 4t-inch-series (smallest first) | 76 of 148 |
| Bore above smallest 4t-inch-series size | 47.3 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| JHM911244 | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; brand-specific OEM equivalents (NSK/FAG/NTN) pending multi-source data. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the JHM911244-JHM911211 model number is decoded
4T-JHM911244/JHM911211 is an NTN inch-series single-row tapered roller bearing: a separable cone-and-cup pair on the ABMA inch boundary plan, 60×130×34.1 mm (assembled width T), for a shaft of about 60 mm (2.362 in). Cone and cup of 4T-JHM911244/JHM911211 are separately stocked parts: a worn JHM911211 cup can be replaced against the existing JHM911244 cone, provided the new cup carries the identical reference — pairing across references changes the 34.1 mm assembled width and the rating. Catalogue mass of the 4T-JHM911244/JHM911211 cone-plus-cup set is 2010 g; shaft and housing shoulders must carry that mass square to the axis during fitting. The printed 173/186 kN ratings belong to the assembled JHM911244+JHM911211 pair; a sibling row using the same cone with a different cup carries its own rating row because the raceway track shifts with the cup. Minimum load matters at speed: an unloaded 4T-JHM911244/JHM911211 run near 2,700 r/min lets the rollers skid; lightly spring-preload high-speed pair arrangements.
Typical equipment & failure modes
Common applications
- crusher and screening-plant eccentric shafts
- heavy truck and bus drive-axle differentials
- plant gearboxes on inch-dimensioned shaft lines
- large conveyor head pulleys in bulk-handling plant
Known failure patterns
- cone-rib and roller large-end smearing when the adjusted pair runs with preload but starved lubricant film
- preload loss and noise after one bearing of the adjusted pair is replaced without resetting end play
- false brinelling on a stationary pair exposed to vibration during transport or standby
- cage damage from a mounting blow transmitted through the roller complement
- water-induced pitting when the open bearing sees washdown without external seals
Selection pitfalls — read before you substitute
- Mount the 60 mm cone by induction heating (max 120 °C) and the 130 mm cup with a press sleeve; at 2010 g a cocked ring brinells the raceway directly.
- The J-prefixed JHM911244 code belongs to a metric-envelope inch family: its 60 mm bore is a round metric figure, yet the part still follows ABMA cone/cup numbering — do not substitute an ISO 355 metric 302/322 bearing of the same bore without checking OD, T and contact angle.
- Do not confuse T (34.1 mm, the assembled cone-plus-cup width) with the cone width when drawing spacers; an abutment sized to T leaves the cup unseated.
- Inch and metric bores collide on paper — 60 mm is 2.362 in, not a round metric size; a metric bearing that seems 0.1 mm off will not seat on the inch shaft.
- Grease packs must leave free volume inside the 34.1 mm-wide set; over-greasing a pair churning near the oil-band speed of 3,600 r/min raises temperature and destroys the setting.
- The 173/186 kN ratings here are NTN Ball and Roller Bearings CAT.No.2203E figures for 4T-JHM911244/JHM911211; internal geometry legitimately differs between inch-series makers, so re-verify ratings, adjustment and the exact cone/cup references before substituting another brand on a rated drive.
Frequently asked questions
What are the dimensions and catalogue ratings of NTN 4T-JHM911244/JHM911211?
4T-JHM911244/JHM911211 is an inch-series single-row tapered roller bearing to the ABMA boundary plan: 60 mm bore (2.362 in), 130 mm outside diameter and 34.1 mm assembled width T (5.118 × 1.343 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 173 kN, C0 186 kN, grease limiting speed 2,700 r/min, oil speed 3,600 r/min, mass about 2010 g. It is an open, separable cone/cup set with a pressed-steel cage.
Are the cone and cup of 4T-JHM911244/JHM911211 interchangeable separately?
Yes — ABMA inch parts are individually interchangeable: the JHM911244 cone or the JHM911211 cup can be replaced by an identical reference from NTN or another ABMA-dimensioned maker. Pairing the cone with a different cup reference is a different catalogue row: OD, assembled T and the 173/186 kN ratings change with the cup.
What is the difference between 4T-JHM911244/JHM911211 and a metric ISO 355 tapered bearing?
4T-JHM911244/JHM911211 follows the ABMA inch boundary plan with cone/cup references; ISO 355 bearings use metric dimension-series numbers (302, 322, …). Even where a metric size looks close to 60×130×34.1 mm, the envelopes and contact angles differ — the two systems are not drop-in interchangeable; check every boundary value before substituting.
What does the 4T prefix on 4T-JHM911244/JHM911211 mean?
4T is NTN's tapered roller bearing quality mark, stamped on cone and cup in the factory. It identifies NTN's 4T programme and is not a dimension or variant code, so interchange lists quote the bare JHM911244/JHM911211 references; the 4T spelling is retained among this page's search aliases.
Why does 4T-JHM911244/JHM911211 list two speeds, 2,700 and 3,600 r/min?
The lower figure, 2,700 r/min, is the grease-lubricated limiting speed — the mechanical ceiling for the cage, rollers and cone-rib contact. With oil lubrication NTN rates 4T-JHM911244/JHM911211 at 3,600 r/min because oil removes rib-contact heat better. Real limits still depend on pair adjustment, oil flow and cooling.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN 2203E 2026-09-25 on 2026-10-01. Read our editorial & correction policy.