L319249-L319210 bearing: complete specifications & equivalents
The L319249-L319210 is a ANSI ABMA 19.2 radial bearing sized 95.25 x 130.175 x 20.638 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 95.25 mm |
| Outer diameter D | 130.175 mm |
| Width B | 20.638 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel |
| Basic dynamic load rating C | 90 kN |
| Basic static load rating C0 | 147 kN |
| Limiting speed (mechanical) | 2500 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 786 g |
| Manufacturer designation | NTN 4T-L319249/L319210 |
| Standard | ANSI ABMA 19.2 |
| Catalog version | NTN 2203E 2026-09-25 |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN 2203E 2026-09-25) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN 2203E 2026-09-25); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 4t-inch-series range
| Bore d | 3.75 in |
|---|---|
| Outer diameter D | 5.125 in |
| Width B | 0.813 in |
| ISO bore code | 49 |
| Radial section height (D−d)/2 | 17.5 mm |
| Smallest bore in 4t-inch-series | 12.7 mm |
| Largest outer diameter in 4t-inch-series | 260 mm |
| Width range across 4t-inch-series | 10.998–77.788 mm |
| Bore position in 4t-inch-series (smallest first) | 113 of 148 |
| Bore above smallest 4t-inch-series size | 82.55 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| L319249 | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; brand-specific OEM equivalents (NSK/FAG/NTN) pending multi-source data. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the L319249-L319210 model number is decoded
The NTN 2203E inch table prints 4T-L319249/L319210 at 95.25 mm bore (3.75 in), 130.175 mm cup OD and 20.638 mm assembled T, with a grease limiting speed of 2,500 r/min and an oil ceiling of 3,300 r/min. The 4T prefix is NTN's tapered roller quality mark stamped on both parts; it is a brand mark, not a size code, so cross-references quote L319249/L319210 without it. Grease relubrication at the 2,500 r/min limiting speed targets the cone-rib contact; sustaining 3,300 r/min needs an oil supply directed at the large roller ends. The printed 90/147 kN ratings belong to the assembled L319249+L319210 pair; a sibling row using the same cone with a different cup carries its own rating row because the raceway track shifts with the cup. Back-to-back (O) and face-to-face (X) arrangements of two 4T-L319249/L319210 sets react differently to shaft bending; choose the orientation for the moment load before locking shoulder geometry.
Typical equipment & failure modes
Common applications
- crusher and screening-plant eccentric shafts
- heavy truck and bus drive-axle differentials
- plant gearboxes on inch-dimensioned shaft lines
- large conveyor head pulleys in bulk-handling plant
Known failure patterns
- cone-rib and roller large-end smearing when the adjusted pair runs with preload but starved lubricant film
- cup creep and housing fretting when the cup seat is cut too loose for the rotating load
- flaking on one cone only when a bent shaft loads the O/X pair unevenly
- pressed-steel cage pocket wear from roller skid at light radial load and high speed
- water-induced pitting when the open bearing sees washdown without external seals
Selection pitfalls — read before you substitute
- Mount the 95.25 mm cone by induction heating (max 120 °C) and the 130.175 mm cup with a press sleeve; at 786 g a cocked ring brinells the raceway directly.
- The light L family at 95.25 mm bore (130.175×20.638 mm assembled) is one of several inch families sharing similar bores; cross-series swaps change OD, T and contact angle, so match the full L319249/L319210 reference at purchase.
- Do not confuse T (20.638 mm, the assembled cone-plus-cup width) with the cone width when drawing spacers; an abutment sized to T leaves the cup unseated.
- ABMA makes the 95.25×130.175 mm envelope interchangeable, not the ratings: NTN prints 90/147 kN for this execution and another make of the same number can differ in roller complement.
- Open 4T-L319249/L319210 sets have no seals: a hub or gearbox needs external sealing or the 2,500 r/min grease figure is meaningless once water reaches the cone rib.
- The 90/147 kN ratings here are NTN Ball and Roller Bearings CAT.No.2203E figures for 4T-L319249/L319210; internal geometry legitimately differs between inch-series makers, so re-verify ratings, adjustment and the exact cone/cup references before substituting another brand on a rated drive.
Frequently asked questions
What are the dimensions and catalogue ratings of NTN 4T-L319249/L319210?
4T-L319249/L319210 is an inch-series single-row tapered roller bearing to the ABMA boundary plan: 95.25 mm bore (3.75 in), 130.175 mm outside diameter and 20.638 mm assembled width T (5.125 × 0.813 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 90 kN, C0 147 kN, grease limiting speed 2,500 r/min, oil speed 3,300 r/min, mass about 786 g. It is an open, separable cone/cup set with a pressed-steel cage.
Are the cone and cup of 4T-L319249/L319210 interchangeable separately?
Yes — ABMA inch parts are individually interchangeable: the L319249 cone or the L319210 cup can be replaced by an identical reference from NTN or another ABMA-dimensioned maker. Pairing the cone with a different cup reference is a different catalogue row: OD, assembled T and the 90/147 kN ratings change with the cup.
What is the difference between 4T-L319249/L319210 and a metric ISO 355 tapered bearing?
4T-L319249/L319210 follows the ABMA inch boundary plan with cone/cup references; ISO 355 bearings use metric dimension-series numbers (302, 322, …). Even where a metric size looks close to 95.25×130.175×20.638 mm, the envelopes and contact angles differ — the two systems are not drop-in interchangeable; check every boundary value before substituting.
What does the 4T prefix on 4T-L319249/L319210 mean?
4T is NTN's tapered roller bearing quality mark, stamped on cone and cup in the factory. It identifies NTN's 4T programme and is not a dimension or variant code, so interchange lists quote the bare L319249/L319210 references; the 4T spelling is retained among this page's search aliases.
Why does 4T-L319249/L319210 list two speeds, 2,500 and 3,300 r/min?
The lower figure, 2,500 r/min, is the grease-lubricated limiting speed — the mechanical ceiling for the cage, rollers and cone-rib contact. With oil lubrication NTN rates 4T-L319249/L319210 at 3,300 r/min because oil removes rib-contact heat better. Real limits still depend on pair adjustment, oil flow and cooling.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN 2203E 2026-09-25 on 2026-10-01. Read our editorial & correction policy.